1.INSPECT SPIRAL CABLE SUB-ASSEMBLY
As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.
Visually check for defects with the spiral cable sub-assembly.
The defects are as follows:
Scratches
Small cracks
Dents
Chips
Cracks or other damage to the connector
No defects are found.
If any of the defects is found, replace the spiral cable sub-assembly with a new one.
Check the spiral cable sub-assembly.
| *a | Component without harness connected
(spiral cable sub-assembly) |
- | - |
|
Interlock | - | - |
When rotating the spiral cable sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.
Set the spiral cable sub-assembly to the center position.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION
Measure the resistance between each terminal of the spiral cable sub-assembly according to the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G4-1 (CCS) - z4-3 | Always | 3 Ω or less |
| G4-2 (ECC) - z4-4 | ||
| G4-3 (EAU) - z2-8 | ||
| G4-5 (AU2) - z2-9 | ||
| G4-6 (AU1) - z2-11 | ||
| G4-7 (SDN) - z2-12 | ||
| G4-9 (HO) - z2-1 | ||
| G4-10 (+DP) - z2-2 | ||
| G4-11 (+DP2) - z2-3 | ||
| G4-13 (IL+2) - z2-5 | ||
| G4-14 (SUP) - z2-6 | ||
| G5-1 (D+) - z3-2 | Below 1 Ω | |
| G5-2 (D-) - z3-1 |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance as shown in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance as shown in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G4-1 (CCS) - z4-3 | Always | 3 Ω or less |
| G4-2 (ECC) - z4-4 | ||
| G4-3 (EAU) - z2-8 | ||
| G4-5 (AU2) - z2-9 | ||
| G4-6 (AU1) - z2-11 | ||
| G4-7 (SDN) - z2-12 | ||
| G4-9 (HO) - z2-1 | ||
| G4-10 (+DP) - z2-2 | ||
| G4-11 (+DP2) - z2-3 | ||
| G4-13 (IL+2) - z2-5 | ||
| G4-14 (SUP) - z2-6 | ||
| G5-1 (D+) - z3-2 | Below 1 Ω | |
| G5-2 (D-) - z3-1 |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G4-1 (CCS) - z4-3 | Always | 3 Ω or less |
| G4-2 (ECC) - z4-4 | ||
| G4-3 (EAU) - z2-8 | ||
| G4-5 (AU2) - z2-9 | ||
| G4-6 (AU1) - z2-11 | ||
| G4-7 (SDN) - z2-12 | ||
| G4-9 (HO) - z2-1 | ||
| G4-10 (+DP) - z2-2 | ||
| G4-11 (+DP2) - z2-3 | ||
| G4-13 (IL+2) - z2-5 | ||
| G4-14 (SUP) - z2-6 | ||
| G5-1 (D+) - z3-2 | Below 1 Ω | |
| G5-2 (D-) - z3-1 |
If the result is not as specified, replace the spiral cable sub-assembly.