Home › Drivetrain › AC60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT › 2015.08–2016.01
RM3270E _52 Drivetrain _041680 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0201469 AUTOMATIC TRANSMISSION UNIT A

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  REASSEMBLY  


PROCEDURE

Hide 1. BEARING POSITION

C327929N01
5.177,0.094 5.333,0.292 0.156,0.198 10 false C 1.688,0.969 1.844,1.167 0.156,0.198 10 false B 0.469,1.385 0.625,1.583 0.156,0.198 10 false A 1.031,4.979 1.188,5.177 0.156,0.198 10 false D 0.844,3.375 1,3.573 0.156,0.198 10 false E 2.094,3.01 2.25,3.208 0.156,0.198 10 false F 3.333,2.677 3.49,2.875 0.156,0.198 10 false G 4.74,2.281 4.896,2.479 0.156,0.198 10 false H 3.198,4.667 3.354,4.865 0.156,0.198 10 false I 5.583,3.948 5.74,4.146 0.156,0.198 10 false J 2.823,6.531 2.979,6.729 0.156,0.198 10 false L 1,7 1.156,7.198 0.156,0.198 10 false K

Bearing and Race Diameter:
Mark Front Race Diameter Inside / Outside (mm (in.)) Thrust Bearing Diameter Inside / Outside (mm (in.)) Rear Race Diameter Inside / Outside (mm (in.))
A 74.2 (2.921) / 87.74 (3.454) 71.9 (2.831) / 85.6 (3.370) -
B 40.0 (1.575) / 52.8 (2.079) 34.6 (1.362) / 52.0 (2.047) -
C 22.0 (0.866) / 44.8 (1.764) 21.3 (0.839) / 41.1 (1.618) -
D 38.4 (1.512) / 56.5 (2.224) 33.3 (1.311) / 56.6 (2.228) -
E - 40.83 (1.607) / 52.8 (2.079) 39.6 (1.559) / 52.8 (2.079)
F - 37.1 (1.461) / 61.2 (2.409) 44.0 (1.732) / 62.8 (2.472)
G 65.8 (2.591) / 86.3 (3.398) 63.3 (2.492) / 78.8 (3.102) -
H 66.3 (2.610) / 78.9 (3.106) 63.3 (2.492) / 78.8 (3.102) -
I - 55.7 (2.193) / 76.4 (3.008) 53.7 (2.114) / 74.0 (2.913)
J 33.4 (1.315) / 49.0 (1.929) 32.1 (1.264) / 49.35 (1.943) 32.1 (1.264) / 49.0 (1.929)
K - 21.0 (0.827) / 41.5 (1.634) 23.13 (0.911) / 41.5 (1.634)
L - 43.55 (1.715) / 61.0 (2.402) 47.1 (1.854) / 67.1 (2.642)


Hide 35639B 2.INSTALL BRAKE PLATE STOPPER SPRING

a.
C321216

Install the 2 brake plate stopper springs to the automatic transmission case sub-assembly.

NOTICE:

The shapes of the parts are different. Refer to the illustration when installing the parts.



Hide 35629A 3.INSTALL NO. 4 BRAKE PISTON

a.

Coat 2 new O-rings with ATF, and install them to the brake reaction sleeve.


b.

Coat 2 new O-rings with ATF, and install them to the No. 4 brake piston.


c.
C109328C02
1.083,0.469 0.917,0.167 0.917,0.167 0.698,0.167 false 2,0.365 1.906,0.188 1.906,0.188 1.688,0.188 false 1.49,0.104 1.802,0.302 0.313,0.198 10 false *1 0.469,0.083 0.781,0.281 0.313,0.198 10 false *2
*1 No. 4 Brake Piston
*2 Brake Reaction Sleeve


Install the No. 4 brake piston to the brake reaction sleeve.

NOTICE:

Be careful not to damage the O-rings.



Hide 35626 4.INSTALL BRAKE REACTION SLEEVE

a.
C322239C01
0.99,1.323 1.188,0.438 1.188,0.438 1.354,0.438 false 1.26,1.542 1.583,0.698 1.583,0.698 1.792,0.698 false 1.406,0.365 1.604,0.604 0.198,0.24 10 false *1 1.854,0.625 2.052,0.865 0.198,0.24 10 false *2
*1 Brake Reaction Sleeve
*2 No. 4 Brake Piston


With the No. 4 brake piston underneath (the rear side), install the brake reaction sleeve and No. 4 brake piston to the automatic transmission case sub-assembly.

NOTICE:

Be careful not to damage the O-rings.



Hide 35623H 5.INSTALL 1ST AND REVERSE BRAKE PISTON

a.
C321231

Coat a new O-ring with ATF, and install it to the 1st and reverse brake piston.


b.

Install the 1st and reverse brake piston to the automatic transmission case sub-assembly while making sure that the protrusion of the 1st and reverse brake piston is positioned as shown in the illustration.

NOTICE:

Be careful not to damage the O-ring.



c.
C322246

Install the 1st and reverse brake return spring sub-assembly to the automatic transmission case sub-assembly.


d.

Place the 1st and reverse brake return spring sub-assembly onto the 1st and reverse brake piston.


e.
C322240C02
0.781,2.083 0.542,0.531 0.542,0.531 0.344,0.531 true 1.052,2 0.854,0.198 0.854,0.198 0.656,0.198 true 0.146,0.438 0.458,0.635 0.313,0.198 10 false *a 0.323,0.115 0.781,0.313 0.458,0.198 10 false SST
*a Protective Tape


Place SST on the 1st and reverse brake return spring sub-assembly, and compress the 1st and reverse brake return spring sub-assembly.

SST
09380-60011  (09381-06030, 09381-05040, 09381-06040, 09381-06080, 09381-05050, 09381-06120, 09381-06130, 09381-06140)


f.

Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.

NOTICE:

Be careful not to damage the 1st and reverse brake return spring sub-assembly and automatic transmission case sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 35760 6.INSTALL REAR PLANETARY GEAR ASSEMBLY

a.
C327925C01
0.854,0.5 1.344,0.5 false 0.865,0.771 1.354,0.771 false 0.823,2.125 1.313,2.125 false 0.823,2.427 1.313,2.427 false 0.677,0.396 0.99,0.552 0.313,0.156 10 false *1 0.688,0.667 1,0.823 0.313,0.156 10 false *2 0.656,2.021 0.969,2.177 0.313,0.156 10 false *3 0.656,2.323 0.969,2.479 0.313,0.156 10 false *4
*1 Thrust Needle Roller Bearing K
*2 Thrust Bearing Race K
*3 Thrust Needle Roller Bearing L
*4 Thrust Bearing Race L


Coat the thrust bearing race with ATF and install it to the automatic transmission case sub-assembly.

Thrust Needle Roller Bearing and Thrust Bearing Race Diameter:
Item Inside (mm (in.)) Outside (mm (in.))
Thrust Needle Roller Bearing K 21.0 (0.827) 41.5 (1.634)
Thrust Bearing Race K 23.13 (0.911) 41.5 (1.634)
Thrust Needle Roller Bearing L 43.55 (1.715) 61.0 (2.402)
Thrust Bearing Race L 47.1 (1.854) 67.1 (2.642)


NOTICE:

Be sure to install the thrust needle roller bearing and thrust bearing race in the correct direction.



b.

Coat the 2 thrust needle roller bearings and thrust bearing races with ATF and install them to the rear planetary gear assembly.


c.

Install the rear planetary gear assembly to the automatic transmission case sub-assembly.


Hide 35684 7.INSTALL NO. 4 BRAKE DISC

a.
C327917C01
1.979,0.219 2.656,0.219 false 1.979,0.406 2.656,0.406 false 1.99,2.51 2.365,2.51 2.365,2.51 2.365,0.406 false 1.979,0.771 2.365,0.771 false 1.979,1.125 2.365,1.125 false 1.979,1.469 2.365,1.469 false 1.979,1.823 2.365,1.823 false 1.979,2.167 2.365,2.167 false 0.51,0.573 1.188,0.573 false 1.188,2.313 0.813,2.313 0.813,2.313 0.813,0.573 false 0.813,0.927 1.198,0.927 false 0.813,1.271 1.198,1.271 false 0.813,1.604 1.198,1.604 false 0.813,1.958 1.198,1.958 false 2,2.708 2.677,2.708 false 2.688,0.104 3,0.26 0.313,0.156 10 false *1 2.688,0.302 3,0.458 0.313,0.156 10 false *2 0.354,0.469 0.667,0.625 0.313,0.156 10 false *3 2.729,2.583 3.042,2.74 0.313,0.156 10 false *1
*1 No. 4 Brake Flange
*2 No. 4 Brake Disc
*3 No. 4 Brake Plate


Install the 2 No. 4 brake flanges, 7 No. 4 brake discs and 6 No. 4 brake plates to the automatic transmission case sub-assembly.

NOTICE:
·

Make sure that the No. 4 brake discs, No. 4 brake plates and No. 4 brake flanges are installed in the correct order.

·

Install the thicker No. 4 brake flange first, and then install the thinner one.




Hide 35713 8.INSTALL INTERMEDIATE SHAFT

a.
C322215C01
0.927,0.781 1.49,0.781 false 0.927,1.052 1.49,1.052 false 0.708,0.698 1.021,0.896 0.313,0.198 10 false *1 0.708,0.979 1.021,1.177 0.313,0.198 10 false *2
*1 Thrust Needle Roller Bearing J
*2 Thrust Bearing Race J (Rear Race)


Coat the thrust needle roller bearing and thrust bearing race with ATF and install them to the intermediate shaft.

Thrust Needle Roller Bearing and Thrust Bearing Race Diameter:
Item Inside (mm (in.)) Outside (mm (in.))
Thrust Needle Roller Bearing J 32.1 (1.264) 49.35 (1.943)
Thrust Bearing Race J
(Rear Race)
32.1 (1.264) 49.0 (1.929)



b.

Install the intermediate shaft to the automatic transmission case sub-assembly.


Hide 35761 9.INSTALL REAR PLANETARY RING GEAR

a.
C321211C01
2.125,0.594 2.615,0.594 false 2.167,1.677 2.656,1.677 false 2.688,0.51 3,0.708 0.313,0.198 10 false *1 2.719,1.594 3.031,1.792 0.313,0.198 10 false *2
*1 Rear Planetary Ring Gear Flange Sub-assembly
*2 Rear Planetary Ring Gear


Install the rear planetary ring gear to the rear planetary ring gear flange sub-assembly.


b.
C321210C01
2.396,0.563 2.708,0.563 false 2.771,0.479 3.083,0.677 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, install the snap ring to the rear planetary ring gear flange sub-assembly with rear planetary ring gear.

NOTICE:

Be careful not to damage the rear planetary ring gear flange sub-assembly with rear planetary ring gear.


HINT:

Tape the screwdriver tip before use.



Hide 35077D 10.INSTALL REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY WITH REAR PLANETARY RING GEAR

a.
C322235C01
0.958,0.896 1.479,0.896 false 0.75,0.813 1.063,1.01 0.313,0.198 10 false *1
*1 Thrust Bearing Race J (Front Race)


Coat the thrust bearing race with ATF and install it to the rear planetary ring gear flange sub-assembly with rear planetary ring gear.

Thrust Bearing Race Diameter:
Item Inside (mm (in.)) Outside (mm (in.))
Thrust Bearing Race J
(Front Race)
33.4 (1.315.) 49.0 (1.929)


NOTICE:

Be sure to install the thrust bearing race in the correct direction.



b.

Install the rear planetary ring gear flange sub-assembly with rear planetary ring gear to the automatic transmission case sub-assembly.


Hide 35797B 11.INSTALL ONE-WAY CLUTCH INNER RACE

a.
C322253C01
2.021,0.552 2.802,0.552 false 2.24,1.323 2.75,1.323 false 2.896,0.469 3.208,0.667 0.313,0.198 10 false *1 2.813,1.26 3.125,1.458 0.313,0.198 10 false *2
*1 One-way Clutch Inner Race
*2 No. 3 One-way Clutch Assembly


Install the one-way clutch inner race to the No. 3 one-way clutch assembly.

HINT:

Rotate the one-way clutch inner race clockwise to install it.



Hide 35770C 12.INSTALL NO. 3 ONE-WAY CLUTCH ASSEMBLY WITH ONE-WAY CLUTCH INNER RACE

a.
C322217

Install the No. 3 one-way clutch assembly with one-way clutch inner race to the automatic transmission case sub-assembly.


b.
C322917C01
1.125,0.792 1.281,1.021 1.281,1.021 1.406,1.021 true 1.448,0.938 1.76,1.094 0.313,0.156 10 false *1 1.927,1.313 2.24,1.469 0.313,0.156 10 false *a 1.188,1.406 1.5,1.563 0.313,0.156 10 false *b
*1 Snap Ring
*a 19°
*b 49°
V100135

Front Side


Using SST, install the snap ring to the automatic transmission case sub-assembly.

SST
09350-30020  (09350-07060)

NOTICE:
·

Install the snap ring so that the tapered side is facing out.

·

Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.




Hide 35621V 14.INSTALL NO. 1 BRAKE PISTON

a.

Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.


b.
C322214

With the No. 1 brake piston return spring sub-assembly installed to the No. 1 brake piston, align the 2 claws of the No. 1 brake piston return spring sub-assembly with the 2 claws of the No. 1 brake cylinder, and then install the No. 1 brake piston to the No. 1 brake cylinder.


Hide 35698 15.INSTALL NO. 1 BRAKE CYLINDER WITH NO. 1 BRAKE PISTON

a.
C322221

Install the No. 1 brake cylinder with No. 1 brake piston to the automatic transmission case sub-assembly while making sure that the 2 claws of the No. 1 brake cylinder with No. 1 brake piston are positioned as shown in the illustration.


Hide 35608J 16.INSTALL NO. 1 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C322219

Align the 2 claws of the No. 1 brake piston return spring sub-assembly with the 2 claws of the No. 1 brake cylinder, and then install the No. 1 brake piston return spring sub-assembly to the No. 1 brake piston.


b.
C321202C02
1.021,1.438 0.823,0.865 0.823,0.865 0.552,0.865 true 3.135,0.188 3.344,0.458 0.208,0.271 10 false *a 0.219,0.792 0.677,0.99 0.458,0.198 10 false SST
*a Turn


Place SST on the No. 1 brake piston return spring sub-assembly, and compress the No. 1 brake piston return spring sub-assembly with a press.

SST
09380-60011  (09381-06010, 09381-06040, 09381-06050, 09381-06070, 09381-06090, 09381-06100, 09381-06110, 09381-06120)


c.
C322919C01
0.333,1.625 0.646,1.781 0.313,0.156 10 false *a 0.427,0.917 0.74,1.073 0.313,0.156 10 false *b
*a 22.5°
*b 37.5°


Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.

NOTICE:
·

Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.

·

Be careful not to damage the automatic transmission case sub-assembly.



HINT:

Tape the screwdriver tip before use.



Hide 35681A 17.INSTALL NO. 1 BRAKE DISC

a.
C327908C01
0.469,0.792 1.156,0.792 false 1.948,0.25 2.635,0.25 false 1.958,0.573 2.646,0.573 false 1.938,2.031 2.323,2.031 2.323,2.031 2.323,0.573 false 1.958,1.052 2.323,1.052 false 1.958,1.531 2.323,1.531 false 1.156,2.229 0.813,2.229 0.813,2.229 0.813,0.792 false 0.813,1.271 1.156,1.271 false 0.813,1.76 1.156,1.76 false 2.698,0.479 3.01,0.635 0.313,0.156 10 false *2 0.302,0.698 0.615,0.854 0.313,0.156 10 false *3 2.688,0.146 3,0.302 0.313,0.156 10 false *1
*1 No. 1 Brake Flange
*2 No. 1 Brake Disc
*3 No. 1 Brake Plate


Install the No. 1 brake flange, 4 No. 1 brake discs and 4 No. 1 brake plates to the automatic transmission case sub-assembly.

NOTICE:

Make sure that the No. 1 brake discs, No. 1 brake plates and No. 1 brake flange are installed in the correct order.



b.
C322918C01
1.479,0.167 1.792,0.323 0.313,0.156 10 false *a 2.125,0.219 2.438,0.375 0.313,0.156 10 false *b
*a 22.5°
*b 37.5°


Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.

NOTICE:
·

Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.

·

Be careful not to damage the automatic transmission case sub-assembly.



HINT:

Tape the screwdriver tip before use.



Hide 35719B 19.INSTALL PLANETARY SUN GEAR

a.
C321200

Install the planetary sun gear to the automatic transmission case sub-assembly.


Hide 35750 20.INSTALL CENTER PLANETARY GEAR ASSEMBLY

a.
C322234C01
0.927,0.417 1.417,0.417 false 0.708,0.333 1.021,0.531 0.313,0.198 10 false *1
*1 Thrust Bearing Race I


Coat the thrust bearing race with ATF and install it to the center planetary gear assembly.

Thrust Bearing Race Diameter:
Item Inside (mm (in.)) Outside (mm (in.))
Thrust Bearing Race I 53.7 (2.114) 74.0 (2.913)



b.

Install the center planetary gear assembly to the automatic transmission case sub-assembly.


Hide 35763 21.INSTALL CENTER PLANETARY RING GEAR

a.
C321198C01
2.25,0.479 2.729,0.479 false 2.323,1.438 2.74,1.438 false 2.823,0.406 3.135,0.604 0.313,0.198 10 false *1 2.813,1.354 3.125,1.552 0.313,0.198 10 false *2
*1 Center Planetary Ring Gear Flange
*2 Center Planetary Ring Gear


Install the center planetary ring gear to the center planetary ring gear flange.


b.
C321197C01
1.417,0.417 1.854,0.417 false 1.927,0.323 2.24,0.521 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, install the snap ring to the center planetary ring gear flange with center planetary ring gear.

NOTICE:

Be careful not to damage the center planetary ring gear flange with center planetary ring gear.


HINT:

Tape the screwdriver tip before use.



Hide 35769 22.INSTALL CENTER PLANETARY RING GEAR FLANGE WITH CENTER PLANETARY RING GEAR

a.
C322233C01
0.813,0.354 1.375,0.354 false 0.823,1.208 1.385,1.208 false 0.625,0.271 0.938,0.469 0.313,0.198 10 false *1 0.615,1.135 0.927,1.333 0.313,0.198 10 false *2
*1 Thrust Needle Roller Bearing H
*2 Thrust Needle Roller Bearing I


Coat the 2 thrust needle roller bearings with ATF and install them to the center planetary ring gear flange with center planetary ring gear.

Thrust Needle Roller Bearing Diameter:
Item Inside (mm (in.)) Outside (mm (in.))
Thrust Needle Roller Bearing H 63.3 (2.492) 78.8 (3.102)
Thrust Needle Roller Bearing I 55.7 (2.193) 76.4 (3.008)


NOTICE:

Be sure to install the thrust needle roller bearing in the correct direction.



b.

Install the center planetary ring gear flange with center planetary ring gear to the automatic transmission case sub-assembly.


Hide 35682A 23.INSTALL NO. 2 BRAKE DISC

a.
C327907C01
1.896,0.25 2.542,0.25 false 1.896,0.49 2.542,0.49 false 1.896,2.063 2.25,2.063 2.25,2.063 2.25,0.49 false 0.542,0.698 1.167,0.698 false 1.896,0.896 2.25,0.896 false 1.896,1.281 2.25,1.281 false 1.896,1.667 2.25,1.667 false 1.167,1.885 0.854,1.885 0.854,1.885 0.854,0.698 false 1.896,2.26 2.563,2.26 false 0.854,1.49 1.156,1.49 false 0.854,1.094 1.156,1.094 false 2.594,0.156 2.906,0.313 0.313,0.156 10 false *1 2.594,0.396 2.906,0.552 0.313,0.156 10 false *2 0.375,0.604 0.688,0.76 0.313,0.156 10 false *3 2.615,2.167 2.927,2.323 0.313,0.156 10 false *1
*1 No. 2 Brake Flange
*2 No. 2 Brake Disc
*3 No. 2 Brake Plate


Install the 2 No. 2 brake flanges, 5 No. 2 brake discs and 4 No. 2 brake plates to the automatic transmission case sub-assembly.

NOTICE:
·

Make sure that the No. 2 brake discs, No. 2 brake plates and No. 2 brake flanges are installed in the correct order.

·

Install the thicker No. 2 brake flange first, and then install the thinner one.




Hide 35622G 24.INSTALL NO. 2 BRAKE PISTON

a.

Coat 2 new O-rings with ATF and install them to the No. 2 brake piston.


b.
C322213

With the No. 2 brake piston return spring sub-assembly installed to the No. 2 brake piston, align the claw of the No. 2 brake piston return spring sub-assembly with the claw of the No. 2 brake cylinder, and then install the No. 2 brake piston to the No. 2 brake cylinder.

NOTICE:

Be careful not to damage the O-rings.



Hide 35699 25.INSTALL NO. 2 BRAKE CYLINDER WITH NO. 2 BRAKE PISTON

a.
C322220

Install the No. 2 brake piston return spring sub-assembly to the automatic transmission case sub-assembly while making sure that the claw of the No. 2 brake piston return spring sub-assembly is positioned as shown in the illustration.


b.
C322222

Install the No. 2 brake cylinder with No. 2 brake piston to the automatic transmission case sub-assembly while making sure that the claw of the No. 1 brake cylinder with No. 1 brake piston is positioned as shown in the illustration.


c.
C321201C02
0.479,0.5 0.688,0.5 0.688,0.5 0.844,0.948 true 3.177,0.271 3.406,0.521 0.229,0.25 10 false *a 0.177,0.427 0.51,0.635 0.333,0.208 10 false SST
*a Turn


Place SST on the No. 2 brake cylinder, and compress the No. 2 brake piston return spring sub-assembly with a press.

SST
09380-60011  (09381-06010, 09381-06020, 09381-06040, 09381-06050, 09381-06060, 09381-06090, 09381-06100, 09381-06110, 09381-06120)


d.
C322920C01
1.385,0.125 1.698,0.281 0.313,0.156 10 false *a 2.063,0.125 2.375,0.281 0.313,0.156 10 false *a
*a 30°


Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.

NOTICE:
·

Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.

·

Be careful not to damage the automatic transmission case sub-assembly.



HINT:

Tape the screwdriver tip before use.



Hide 35076C 27.INSTALL FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

a.
C321195C01
2.125,3.396 2.625,3.396 false 2.167,2.552 2.625,2.552 false 2.167,4.052 2.604,4.052 false 2.698,2.469 3.01,2.667 0.313,0.198 10 false *1 2.698,3.313 3.01,3.51 0.313,0.198 10 false *2 2.688,3.979 3,4.177 0.313,0.198 10 false *3
*1 Front Planetary Ring Gear
*2 Snap Ring
*3 Front Planetary Ring Gear Flange Sub-assembly


Set the snap ring onto the front planetary ring gear flange sub-assembly. Using needle-nose pliers, insert the snap ring into the front planetary ring gear while squeezing it, and then expand the snap ring to install it.

NOTICE:

Make sure the snap ring is securely inserted into the groove of the front planetary ring gear.



Hide 35743 28.INSTALL FRONT PLANETARY RING GEAR WITH FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

a.
C322232C01
0.875,0.313 1.406,0.313 false 0.875,1.219 1.406,1.219 false 0.667,0.25 0.979,0.448 0.313,0.198 10 false *1 0.667,1.146 0.906,1.354 0.24,0.208 10 false *2
*1 Thrust Needle Roller Bearing G
*2 Thrust Bearing Race H


Coat the thrust needle roller bearing and thrust bearing race with ATF and install them to the front planetary ring gear with front planetary ring gear flange sub-assembly.

Thrust Needle Roller Bearing and Thrust Bearing Race Diameter:
Item Inside (mm (in.)) Outside (mm (in.))
Thrust Needle Roller Bearing G 63.3 (2.492) 78.8 (3.102)
Thrust Bearing Race H 66.3 (2.610) 78.9 (3.106)


NOTICE:

Be sure to install the thrust needle roller bearing and thrust bearing race in the correct direction.



b.

Install the front planetary ring gear with front planetary ring gear flange sub-assembly to the automatic transmission case sub-assembly.


Hide 35720 29.INSTALL FRONT PLANETARY GEAR ASSEMBLY

a.
C322231C01
0.833,0.25 1.438,0.25 false 0.885,1.073 1.354,1.073 false 0.635,0.177 0.948,0.375 0.313,0.198 10 false *1 0.656,1.01 0.969,1.208 0.313,0.198 10 false *2
*1 Thrust Bearing Race F
*2 Thrust Bearing Race G


Coat the 2 thrust bearing races with ATF and install them to the front planetary gear assembly.

Thrust Bearing Race Diameter:
Item Inside (mm (in.)) Outside (mm (in.))
Thrust Bearing Race F 44.0 (1.732) 62.8 (2.472)
Thrust Bearing Race G 65.8 (2.591) 86.3 (3.398)


NOTICE:

Be sure to install the thrust bearing race in the correct direction.



b.

Install the front planetary gear assembly to the automatic transmission case sub-assembly.


Hide 35709J 30.INSTALL SUN GEAR INPUT DRUM SUB-ASSEMBLY

a.
C322230C01
0.865,0.385 1.5,0.385 false 0.823,1.083 1.458,1.083 false 0.656,0.323 0.969,0.521 0.313,0.198 10 false *1 0.646,1.01 0.958,1.208 0.313,0.198 10 false *2
*1 Thrust Bearing Race E
*2 Thrust Needle Roller Bearing F


Coat the thrust needle roller bearing and thrust bearing race with ATF and install them to the sun gear input drum sub-assembly.

Thrust Needle Roller Bearing and Thrust Bearing Race Diameter:
Item Inside (mm (in.)) Outside (mm (in.))
Thrust Bearing Race E 40.83 (1.607) 52.8 (2.079)
Thrust Needle Roller Bearing F 37.1 (1.461) 61.2 (2.409)


NOTICE:

Be sure to install the thrust needle roller bearing and thrust bearing race in the correct direction.



b.

Install the sun gear input drum sub-assembly to the automatic transmission case sub-assembly.


Hide 35061 31.INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY

a.
C322229C01
0.802,0.323 1.479,0.323 false 0.792,1.115 1.469,1.115 false 0.604,0.25 0.917,0.448 0.313,0.198 10 false *1 0.604,1.042 0.917,1.24 0.313,0.198 10 false *2
*1 Thrust Needle Roller Bearing D
*2 Thrust Needle Roller Bearing E


Coat the 2 thrust needle roller bearings with ATF and install them to the forward clutch hub sub-assembly.

Thrust Needle Roller Bearing Diameter:
Item Inside (mm (in.)) Outside (mm (in.))
Thrust Needle Roller Bearing D 33.3 (1.311) 56.6 (2.228)
Thrust Needle Roller Bearing E 39.6 (1.559) 52.8 (2.079)


NOTICE:

Be sure to install the thrust needle roller bearing in the correct direction.



b.

Install the forward clutch hub sub-assembly to the automatic transmission case sub-assembly.


Hide 35631 32.INSTALL MULTIPLE DISC CLUTCH HUB

a.
C322228C01
0.875,0.333 1.438,0.333 false 0.917,1.104 1.375,1.104 false 0.688,0.26 1,0.458 0.313,0.198 10 false *1 0.688,1.031 1,1.229 0.313,0.198 10 false *2
*1 Thrust Bearing Race C
*2 Thrust Bearing Race D


Coat the 2 thrust bearing races with ATF and install them to the multiple disc clutch hub.

Thrust Bearing Race Diameter:
Item Inside (mm (in.)) Outside (mm (in.))
Thrust Bearing Race C 22.6 (0.866) 44.8 (1.764)
Thrust Bearing Race D 38.4 (1.512) 56.5 (2.224)


NOTICE:

Be sure to install the thrust bearing race in the correct direction.



b.

Install the multiple disc clutch hub to the automatic transmission case sub-assembly.


Hide 35652C 33.INSTALL DIRECT CLUTCH PISTON

a.

Coat 2 new O-rings with ATF, and install them to the direct clutch piston.


b.
C322898

Install the direct clutch piston to the direct clutch drum sub-assembly.

NOTICE:

Be careful not to damage the O-rings.



Hide 35669 34.INSTALL NO. 2 CLUTCH BALANCER

a.
C321222C01
2.156,0.344 2.427,0.344 false 2.021,1.021 2.479,1.021 false 2.5,0.281 2.813,0.479 0.313,0.198 10 false *1 2.542,0.948 2.854,1.146 0.313,0.198 10 false *2
*1 No. 2 Clutch Balancer
*2 Direct Clutch Return Spring Sub-assembly


Install the direct clutch return spring sub-assembly to the direct clutch piston.


b.

Coat a new O-ring with ATF, and install it to the No. 2 clutch balancer.


c.

Install the No. 2 clutch balancer to the direct clutch drum sub-assembly.

NOTICE:

Be careful not to damage the O-ring.



d.
C322223N03
1.094,0.677 0.781,0.167 0.781,0.167 1.396,0.333 true 0.469,0.094 0.854,0.281 0.385,0.188 10 false SST

Place SST on the No. 2 clutch balancer, and compress the direct clutch return spring sub-assembly with a press.

SST
09380-60011  (09381-06030, 09381-06040, 09381-06080, 09381-06100, 09381-06110)

NOTICE:

Stop pressing when the spring sheet is lowered to the place 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.



e.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:

Do not expand the snap ring excessively.



Hide 35667A 35.INSTALL NO. 2 CLUTCH DISC (DIRECT CLUTCH DISC)

a.
C327906C01
2.104,0.333 2.656,0.333 false 2.094,0.625 2.646,0.625 false 2.083,2.146 2.396,2.146 2.396,2.146 2.396,0.625 false 2.083,1.021 2.396,1.021 false 2.094,1.406 2.396,1.406 false 2.083,1.781 2.396,1.781 false 0.635,0.802 1.188,0.802 false 1.177,2.323 0.865,2.323 0.865,2.323 0.865,0.802 false 0.865,1.958 1.177,1.958 false 0.865,1.583 1.177,1.583 false 0.865,1.198 1.177,1.198 false 2.708,0.229 3.021,0.385 0.313,0.156 10 false *1 2.698,0.531 3.01,0.688 0.313,0.156 10 false *2 0.469,0.708 0.781,0.865 0.313,0.156 10 false *3
*1 Direct Clutch Flange
*2 No. 2 Clutch Disc
*3 No. 2 Clutch Plate


Install the 5 No. 2 clutch plates, 5 No. 2 clutch discs and direct clutch flange to the direct clutch drum sub-assembly.

NOTICE:

Make sure that the No. 2 clutch discs, No. 2 clutch plates and direct clutch flange are installed in the correct order.



b.
C321219C01
2.521,0.604 2.74,0.604 false 2.802,0.531 3.115,0.729 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, install the snap ring to the direct clutch drum sub-assembly.

NOTICE:

Be careful not to damage the direct clutch drum sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 35675C 36.INSPECT CLEARANCE OF NO. 2 CLUTCH (DIRECT CLUTCH)

Hide 35612B 37.INSTALL FORWARD CLUTCH PISTON

a.

Coat a new O-ring with ATF, and install it to the input shaft sub-assembly.


b.

Coat a new O-ring with ATF, and install it to the forward clutch piston.


c.
C327914

Install the forward clutch piston to the input shaft sub-assembly.

NOTICE:

Be careful not to damage the O-rings.



Hide 35668 38.INSTALL NO. 1 CLUTCH BALANCER

a.

Coat a new O-ring with ATF, and install it to the No. 1 clutch balancer.


b.
C321229C01
2.208,0.385 2.604,0.385 false 2.104,0.948 2.635,0.948 false 2.677,0.313 2.99,0.51 0.313,0.198 10 false *1 2.708,0.885 3.021,1.083 0.313,0.198 10 false *2
*1 No. 1 Clutch Balancer
*2 Forward Clutch Return Spring Sub-assembly


Install the forward clutch return spring sub-assembly and No. 1 clutch balancer to the input shaft sub-assembly.

NOTICE:

Be careful not to damage the O-ring.



c.
C321228N01
2.625,1.188 3.031,1.729 3.031,1.729 2.74,0.781 false 2.938,1.771 3.26,1.958 0.323,0.188 10 true SST

Place SST on the No. 1 clutch balancer, and compress the forward clutch return spring sub-assembly with a press.

SST
09387-00110  

NOTICE:

Stop pressing when the spring sheet is lowered to the place 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.



d.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:

Do not expand the snap ring excessively.



Hide 35633B 39.INSTALL NO. 1 CLUTCH DISC (FORWARD CLUTCH DISC)

a.
C321227C02
0.635,0.646 1.344,0.646 false 0.813,0.646 0.813,1.896 0.813,1.896 1.385,1.896 false 0.813,1.563 1.354,1.563 false 0.823,1.271 1.365,1.271 false 0.813,0.958 1.354,0.958 false 2.396,0.51 2.396,1.75 2.396,1.75 2.094,1.75 false 2.104,0.844 2.396,0.844 false 2.083,0.51 2.646,0.51 false 2.104,1.146 2.396,1.146 false 2.104,1.458 2.396,1.458 false 2.146,0.281 2.635,0.281 false 0.427,0.563 0.74,0.76 0.313,0.198 10 false *3 2.729,0.438 3.042,0.635 0.313,0.198 10 false *2 2.719,0.177 3.031,0.375 0.313,0.198 10 false *1
*1 Forward Clutch Flange
*2 No. 1 Clutch Disc
*3 No. 1 Clutch Plate


Install the 5 No. 1 clutch plates, 5 No. 1 clutch discs and forward clutch flange to the input shaft sub-assembly.

NOTICE:

Make sure that the No. 1 clutch discs, No. 1 clutch plates and forward clutch flange are installed in the correct order.



b.
C321226C01
2.188,0.458 2.604,0.458 false 2.688,0.385 3,0.583 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, install the snap ring.

NOTICE:

Be careful not to damage the input shaft sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 35635 40.INSPECT CLEARANCE OF NO. 1 CLUTCH (FORWARD CLUTCH)

Hide 35617 41.INSTALL CLUTCH DRUM OIL SEAL RING

a.
C322944

Coat 3 new clutch drum oil seal rings with ATF and install them to the input shaft sub-assembly.

NOTICE:

Do not expand the clutch drum oil seal ring ends excessively.


HINT:

After installing the clutch drum oil seal rings, check that they rotate smoothly.



Hide 35605A 42.INSTALL DIRECT CLUTCH DRUM SUB-ASSEMBLY

a.
C322943C01
2.177,0.521 2.625,0.521 false 2.021,1.781 2.635,1.781 false 2.667,0.417 2.979,0.573 0.313,0.156 10 false *1 2.677,1.688 2.99,1.844 0.313,0.156 10 false *2
*1 Direct Clutch Drum Sub-assembly
*2 Input Shaft Sub-assembly


Install the direct clutch drum sub-assembly to the input shaft sub-assembly.


Hide 43.INSTALL CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

a.
C327915C01
0.938,0.74 1.417,0.74 false 0.938,1.052 1.469,1.052 false 0.969,2.344 1.479,2.344 false 0.76,0.646 1.073,0.802 0.313,0.156 10 false *1 0.76,0.958 1.073,1.115 0.313,0.156 10 false *2 0.792,2.25 1.104,2.406 0.313,0.156 10 false *3
*1 Thrust Needle Roller Bearing A
*2 Thrust Needle Roller Bearing B
*3 Thrust Needle Roller Bearing C


Coat the 3 thrust needle roller bearings with ATF and install them to the clutch drum and input shaft assembly.

Thrust Needle Roller Bearing Diameter:
Item Inside (mm (in.)) Outside (mm (in.))
Thrust Needle Roller Bearing A 71.9 (2.831) 85.6 (3.370)
Thrust Needle Roller Bearing B 34.6 (1.362) 52.0 (2.047)
Thrust Needle Roller Bearing C 21.3 (0.839) 41.1 (1.618)


NOTICE:

Be sure to install the thrust needle roller bearing in the correct direction.



b.

Install the clutch drum and input shaft assembly to the automatic transmission case sub-assembly.


Hide 44.INSTALL OIL PUMP ASSEMBLY

a.
C322900C01
0.625,0.302 1.49,0.302 false 0.625,0.677 1.438,0.677 false 0.646,1.292 1.052,1.292 false 0.417,0.229 0.729,0.427 0.313,0.198 10 false *1 0.417,0.594 0.729,0.792 0.313,0.198 10 false *2 0.427,1.219 0.74,1.417 0.313,0.198 10 false *3
*1 Thrust Bearing Race B
*2 Thrust Bearing Race A
*3 Oil Pump O-ring


Coat the 2 thrust bearing races with ATF and install them to the oil pump assembly.

Race Diameter:
Item Inside (mm (in.)) Outside (mm (in.))
Thrust Bearing Race B 40.0 (1.575) 52.8 (2.079)
Thrust Bearing Race A 74.2 (2.921) 87.74 (3.454)


NOTICE:

Be sure to install the thrust bearing race in the correct direction.



b.

Coat a new oil pump O-ring with ATF, and install it to the oil pump assembly.


c.

Set the oil pump assembly on the input shaft, and align the bolt holes of the oil pump assembly with the automatic transmission case sub-assembly.

NOTICE:

Be careful not to damage the oil pump O-ring.



d.

Temporarily install the oil pump assembly to the automatic transmission case sub-assembly.


e.
C321186

Install the oil pump assembly with the 10 bolts.

Torque:
21.1 N*m (215 kgf*cm, 16 ft.*lbf)


Hide 35506F 45.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C321239N02
1.083,3.635 0.469,2.427 0.469,2.427 1.177,1.021 true 0.115,2.354 0.573,2.552 0.458,0.198 10 false SST

Using SST and a hammer, drive in 2 new manual valve lever shaft oil seals to the automatic transmission case sub-assembly.

SST
09350-30020  (09350-07110)

Standard depth:

-0.5 to 0.5 mm (-0.0196 to 0.0196 in.)



b.

Coat the lip of the manual valve lever shaft oil seal with MP grease.


Hide 35505 46.INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY

a.
C321240C01
0.844,0.646 0.948,0.208 0.948,0.208 1.177,0.208 false 0.656,1.708 0.875,1.708 0.875,1.708 1.115,1.219 false 1.26,0.146 1.573,0.344 0.313,0.198 10 false *1 0.458,1.625 0.771,1.823 0.313,0.198 10 false *2
*1 Manual Valve Lever Sub-assembly
*2 Spacer


Install a new spacer to the manual valve lever sub-assembly.


b.

Install the manual valve lever shaft to the automatic transmission case sub-assembly through the manual valve lever sub-assembly.


c.
C322929

Using a hammer, drive in a new spring pin.


d.

Turn the spacer and manual valve lever shaft to align the smaller hole on the spacer with the indent on the manual valve lever sub-assembly.


e.
C322928

Using a 3 mm pin punch and a hammer, stake the spacer.


f.

Check that the spacer does not turn.


g.

Make sure that the shaft rotates smoothly.


Hide 35556 47.INSTALL PARKING LOCK PAWL SHAFT

a.

Install the E-ring to the parking lock pawl shaft.


b.
C321182C02
1.354,0.344 1.625,0.344 false 0.802,0.438 0.979,0.438 0.979,0.438 1.75,1.167 true 0.479,0.698 0.667,0.698 0.667,0.698 1.771,1.333 true 0.438,1.021 0.573,1.021 0.573,1.021 1.781,1.854 true 1.115,0.271 1.344,0.448 0.229,0.177 10 true *1 0.594,0.354 0.823,0.531 0.229,0.177 10 true *2 0.292,0.615 0.521,0.792 0.229,0.177 10 true *3 0.26,0.938 0.49,1.115 0.229,0.177 10 true *4
*1 Parking Lock Pawl
*2 E-ring
*3 Parking Lock Pawl Shaft
*4 Spring


Install the parking lock pawl, parking lock pawl shaft and spring to the automatic transmission case sub-assembly.


Hide 35501 48.INSTALL PARKING LOCK ROD SUB-ASSEMBLY

a.
C321181

Install the parking lock rod sub-assembly to the manual valve lever sub-assembly.


Hide 35595 49.INSTALL PARKING LOCK PAWL BRACKET

a.
C321180

Install the parking lock pawl bracket to the automatic transmission case sub-assembly with the 3 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Move the manual valve lever sub-assembly to P, and check the output shaft is locked by the parking lock pawl.


Hide 35159 50.INSTALL BRAKE DRUM GASKET

a.
C321179

Coat 2 new brake drum gaskets with ATF and install them to the automatic transmission case sub-assembly.


Hide 35145C 51.INSTALL TRANSMISSION CASE GASKET

a.
C318514

Coat 2 new transmission case gaskets with ATF and install them to the automatic transmission case sub-assembly.


Hide 35410 52.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.
C322901C02
1.021,0.542 1.125,0.167 1.125,0.167 1.354,0.167 true 1.427,0.719 1.823,0.146 1.823,0.146 2.042,0.146 true 1.406,0.073 1.719,0.271 0.313,0.198 10 false *1 2.135,0.073 2.448,0.271 0.313,0.198 10 false *2 1.854,1.208 2.01,1.406 0.156,0.198 10 false A 2.188,1.24 2.344,1.438 0.156,0.198 10 false A 2.833,1.823 2.99,2.021 0.156,0.198 10 false A 2.885,2.74 3.042,2.938 0.156,0.198 10 false A 0.938,3.146 1.094,3.344 0.156,0.198 10 false A 0.948,1.25 1.104,1.448 0.156,0.198 10 false A 0.49,1.302 0.646,1.5 0.156,0.198 10 false B 0.375,1.99 0.531,2.188 0.156,0.198 10 false B 0.281,2.802 0.438,3 0.156,0.198 10 false B 0.281,2.281 0.438,2.479 0.156,0.198 10 false C 2.906,2.198 3.063,2.396 0.156,0.198 10 false C 1.208,2.073 1.365,2.271 0.156,0.198 10 true A
*1 Manual Valve Lever Sub-assembly
*2 Manual Valve


Insert the manual valve lever sub-assembly into the groove on the end of the manual valve and install the transmission valve body assembly to the automatic transmission case sub-assembly with the 12 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)

Bolt Length:
Item Length
Bolt A 25 mm (0.984 in.)
Bolt B 36 mm (1.42 in.)
Bolt C 50 mm (1.97 in.)



b.
C320631

Install the detent spring and detent spring cover to the transmission valve body assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 35330 53.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.

Coat a new O-ring with ATF, and install it to the valve body oil strainer assembly.


b.
C320630

Install the valve body oil strainer assembly to the transmission valve body assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 82125J 54.INSTALL TRANSMISSION WIRE

a.
C181076

Coat 2 new O-rings with ATF, and install them to the 2 temperature sensors.


b.
C318508

Coat a new O-ring with ATF, and install it to the transmission wire.


c.
C322258

Install the transmission wire to the automatic transmission case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


d.
C318506C04
2.198,1.229 2.365,0.302 2.365,0.302 2.615,0.302 true 2.115,1.198 1.958,0.417 1.958,0.417 1.76,0.417 true 0.656,2.927 0.854,2.927 0.854,2.927 1.083,2.313 true 1.948,3.083 1.604,3.083 1.604,3.083 1.198,2.406 true 2.708,0.25 3.031,0.51 0.323,0.26 10 false *1 1.521,0.333 1.833,0.531 0.313,0.198 10 false *2 0.458,2.854 0.771,3.052 0.313,0.198 10 false *2 2.042,3.021 2.354,3.219 0.313,0.198 10 false *1 1.146,2.792 1.302,2.99 0.156,0.198 10 false B 2.563,1.167 2.719,1.365 0.156,0.198 10 true A
*1 Temperature Sensor Clamp
*2 Temperature Sensor


Connect the 7 solenoid valve connectors.


e.

Install the 2 temperature sensors and 2 temperature sensor clamps to the transmission valve body assembly with the bolt.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 35106 55.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

a.
C323864

Install the 4 transmission oil cleaner magnets to the automatic transmission oil pan sub-assembly as shown in the illustration.


b.

Install a new automatic transmission oil pan gasket to the automatic transmission oil pan sub-assembly.


c.
C323966

Install the automatic transmission oil pan sub-assembly with automatic transmission oil pan gasket to the automatic transmission case sub-assembly with the 10 bolts.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)

NOTICE:
C157303C07
1.875,3.479 2.51,3.479 true 0.906,3.844 1.542,3.844 true 0.698,0.24 1.01,0.438 0.313,0.198 10 false *a 1.604,0.24 1.917,0.438 0.313,0.198 10 false *b 2.344,2.615 2.656,2.813 0.313,0.198 10 false *c 2.479,0.24 2.792,0.438 0.313,0.198 10 false *b 0.698,3.75 1.01,3.948 0.313,0.198 10 false *1 2.604,3.396 2.917,3.594 0.313,0.198 10 false *2
*1 Sleeve
*2 Automatic Transmission Case Sub-assembly
*a Correct
*b Incorrect
*c Protrusion


·

Make sure that automatic transmission oil pan gasket seal surface and automatic transmission oil pan sub-assembly contact surface are free of oil and foreign matter.

·

Install the automatic transmission oil pan gasket so that there is no slack in the automatic transmission oil pan gasket, and the entire seal surface is level.

·

Make sure that the 8 protrusions are properly engaged to the automatic transmission oil pan sub-assembly.

·

When installing the automatic transmission oil pan sub-assembly, make sure that the automatic transmission oil pan gasket is not pinched between the sleeve and the seal surface of the automatic transmission case sub-assembly.




d.

Install the drain plug and a new gasket to the automatic transmission oil pan sub-assembly.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


e.

Using a 5 mm hexagon socket wrench, install a new gasket and overflow plug to the automatic transmission oil pan sub-assembly.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 35111 56.INSTALL AUTOMATIC TRANSMISSION HOUSING

a.

Clean and degrease the bolts and bolt holes with non-residue solvent.


b.
C327919

Install the automatic transmission housing to the automatic transmission case sub-assembly with the 8 bolts.

Torque:
33.9 N*m (346 kgf*cm, 25 ft.*lbf)


c.

Apply adhesive to 2 or 3 threads on the end of the 4 bolts.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



d.
C327920N01
0.667,1.594 0.823,1.792 0.156,0.198 10 true B 2.448,1.656 2.604,1.854 0.156,0.198 10 true B 0.958,1.708 1.115,1.906 0.156,0.198 10 true A 2.115,1.802 2.271,2 0.156,0.198 10 true A

Install 4 bolts to the automatic transmission housing.

Torque:
for Bolt A (M10 bolt) : 33.9 N*m (346 kgf*cm, 25 ft.*lbf)
for Bolt B (M12 bolt) : 56.8 N*m (579 kgf*cm, 42 ft.*lbf)


Hide 35157B 57.INSTALL REAR TRANSFER CASE ADAPTER OIL RECEIVER

a.
C322939

Install the rear transfer case adapter oil receiver to the transfer adapter sub-assembly.


b.

Using snap ring pliers, install the snap ring to the transfer adapter sub-assembly.


Hide 36117A 58.INSTALL TRANSFER ADAPTER OIL SEAL

a.
C327916N01
1.385,1.26 2.198,1.427 2.198,1.427 1.302,0.99 true 2.271,1.344 2.729,1.542 0.458,0.198 10 false SST

Using SST and a hammer, drive in a new transfer adapter oil seal to the transfer adapter sub-assembly.

SST
09950-60010  (09951-00650)
09950-70010  (09951-07150)

Standard depth:

0 to 0.5 mm (0 to 0.0197 in.)



b.

Coat the lip of the transfer adapter oil seal with MP grease.


Hide 36107A 59.INSTALL TRANSFER ADAPTER SUB-ASSEMBLY

a.
C327923

Using a plastic-faced hammer, tap 2 new straight pins into the transfer adapter sub-assembly.

Standard Protrusion Height:

5.7 to 6.3 mm (0.225 to 0.248 in.)


HINT:

It is not necessary to remove the straight pins they are being replaced.



b.

Clean and degrease the threads of the 10 bolts, bolt holes and the contact surfaces of the automatic transmission case sub-assembly and transfer adapter sub-assembly with non-residue solvent.


c.
C322940C01
0.542,0.813 1.188,0.813 true 0.354,0.719 0.667,0.875 0.313,0.156 10 false *a
*a Seal Packing


Apply seal packing to the transfer adapter sub-assembly as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Apply seal packing in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface.

·

After applying seal packing, install the transfer adapter sub-assembly to the automatic transmission case sub-assembly within 3 minutes and tighten the bolts within 10 minutes.




d.

Apply adhesive to 2 or 3 threads on the end of the 10 bolts.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



e.
C324560N01
1.063,1.365 1.219,1.563 0.156,0.198 10 true A 0.99,1.833 1.146,2.031 0.156,0.198 10 false A 2.552,1.823 2.708,2.021 0.156,0.198 10 false A 1.76,1.771 1.917,1.969 0.156,0.198 10 true A 2.385,1.385 2.542,1.583 0.156,0.198 10 true A 0.99,1.063 1.146,1.26 0.156,0.198 10 true B 2.469,1.073 2.625,1.271 0.156,0.198 10 true B 2.313,0.458 2.469,0.656 0.156,0.198 10 true B 1.729,0.146 1.885,0.344 0.156,0.198 10 true B 1.125,0.438 1.271,0.594 0.146,0.156 10 true B

Install the transfer adapter sub-assembly to the automatic transmission case sub-assembly with the 10 bolts.

Torque:
33.9 N*m (346 kgf*cm, 25 ft.*lbf)

Bolt Length:
Item Length
Bolt A 40 mm (1.57 in.)
Bolt B 50 mm (1.97 in.)



Hide 60.INSTALL OIL COOLER TUBE UNION

a.

Coat 2 new O-rings with ATF and install them to the 2 oil cooler tube unions.


b.
C321247C02
0.979,1.969 0.719,0.875 0.719,0.875 0.531,0.875 true 0.208,0.781 0.667,0.979 0.458,0.198 10 false SST 1.646,0.927 1.958,1.125 0.313,0.198 10 false *a 3.073,2.052 3.292,2.26 0.219,0.208 10 true *b 2.958,2.521 3.177,2.729 0.219,0.208 10 true *c
*a Torque Wrench Fulcrum Length
*b 18° to 22°
*c -2° to 2°


Using SST, install the 2 oil cooler tube unions to the automatic transmission case sub-assembly.

SST
09268-78010  

Torque:
Specified tightening torque : 29.4 N*m (300 kgf*cm, 22 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 34.5 mm (1.3583 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 24.7 N*m (252 kgf*cm, 18 ft.*lbf)




Hide 35104A 61.INSTALL AUTOMATIC TRANSMISSION CASE PLUG

a.

Coat 6 new O-rings with ATF, and install them to the 6 automatic transmission case plugs.


b.
C321170

Install the 6 automatic transmission case plugs to the automatic transmission case sub-assembly.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


c.

Coat a new O-ring with ATF, and install it to the automatic transmission case plug.


d.
C321171

Using a T55 "TORX" socket wrench, install the automatic transmission case plug to the automatic transmission case sub-assembly.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 35108C 62.INSTALL REFILL PLUG

a.

Coat a new O-ring with ATF, and install it to the refill plug.


b.
C323948

Install the refill plug to the transfer adaptor sub-assembly.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 84540 63.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

HINT:

Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch assembly as the detent spring may become detached from the manual valve lever shaft.


a.

Clean the bolt and bolt hole.


b.

Apply adhesive to 2 or 3 threads on the end of the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

Install the bolt within 3 minutes of applying adhesive.



c.
C323972

Temporarily install the park/neutral position switch assembly to the automatic transmission case sub-assembly with the bolt.


d.

Install the lock washer and nut to the park/neutral position switch assembly.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


e.

Temporarily install the transmission control shaft lever LH to the manual valve lever shaft with the spring washer and nut.


f.
C326305N01
1.01,0.031 1.167,0.229 0.156,0.198 10 true N

Turn the transmission control shaft lever LH clockwise until it stops, and then return the transmission control shaft lever LH counterclockwise 2 notches to N.


g.
D025795C16
1.958,0.781 1.833,0.104 1.833,0.104 1.719,0.104 true 1.969,1.573 1.042,1.417 1.042,1.417 0.802,1.417 true 1.469,0.031 1.74,0.208 0.271,0.177 10 false *a 0.573,1.313 0.823,1.51 0.25,0.198 10 false *b
*a Neutral Basic Line
*b Groove


Align the neutral basic line with the groove as shown in the illustration, and tighten the bolt.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


h.

Using a screwdriver, bend the tabs of the lock washer.

NOTICE:
·

Be careful not to damage the park/neutral position switch assembly.

·

Bend at least 2 of the lock washer tabs.



HINT:

Tape the screwdriver tip before use.



Hide 35573 64.INSTALL TRANSMISSION CONTROL SHAFT LEVER LH

a.
C324555

Install the transmission control shaft lever LH to the manual valve lever shaft with the spring washer and nut.

Torque:
15.7 N*m (160 kgf*cm, 12 ft.*lbf)


Hide 89413B 65.INSTALL TRANSMISSION REVOLUTION SENSOR

a.

Coat a new O-ring with ATF, and install it to the transmission revolution sensor (NT).


b.
C323955

Install the transmission revolution sensor (NT) to the automatic transmission case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.
C323956

Coat a new O-ring with ATF, and install it to the transmission revolution sensor (SP2).


d.

Install the transmission revolution sensor (SP2) to the automatic transmission case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 35104V 66.INSTALL BREATHER PLUG HOSE

a.
C327921C01
0.823,0.406 0.823,0.115 0.823,0.115 1.031,0.115 false 1.615,0.885 1.615,0.594 1.615,0.594 1.781,0.594 false 2.729,1.302 2.729,1.01 2.729,1.01 2.896,1.01 false 2.396,1.771 2.688,1.771 false 1.094,0 1.406,0.156 0.313,0.156 10 false *1 1.844,0.479 2.156,0.635 0.313,0.156 10 false *2 2.948,0.896 3.26,1.052 0.313,0.156 10 false *3 2.24,1.677 2.552,1.833 0.313,0.156 10 false *4
*1 Breather Plug Sub-assembly
*2 Breather Plug Hose
*3 Breather Plug
*4 O-ring


Install the breather plug sub-assembly and breather plug to the breather plug hose.


b.

Coat a new O-ring with ATF, and install it to the breather plug.


c.
C322937

Install the breather plug hose to the automatic transmission case sub-assembly.

NOTICE:

Be careful not to damage the O-rings.