Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
Replace any other damaged parts as necessary.
72620B
1.INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY
| *1 | Cable End |
|
Install in this Direction |
Turn the cable end in the installation direction shown in the illustration to install the cable end.
Attach the casing cap.
Install at the gray casing cap side.
| *1 | Wiring Harness Clamp A |
| *2 | Joint Case |
Attach the 3 wiring harness clamps to install the rear No. 1 seat lock cable assembly.
Secure wiring harness clamp A to the vertical wire of the seat cushion.
Secure the joint case between the wires.
78920B
2.INSTALL NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY LH
| *1 | Cable End |
|
Install in this Direction |
Turn the cable end in the installation direction shown in the illustration to install the cable end.
Attach the casing cap and install No. 1 fold seat lock control cable assembly LH.
78950
3.INSTALL NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY
|
Install in this Direction |
Pass the No. 1 fold seat stopper band assembly through itself to install it as shown in the illustration.
79104
4.INSTALL NO. 1 SEATBACK FRAME SUB-ASSEMBLY LH
Install the No. 1 seatback frame sub-assembly LH with 4 bolts.
| *1 | Side Frame |
| *2 | Pipe |
|
Install in this Direction |
Pass the rear No. 1 seat lock cable assembly through as shown in the illustration.
Pass it through the hole in the side frame.
Pass it under the pipe.
| *1 | Cable End |
|
Install in this Direction |
Turn the cable end in the installation direction shown in the illustration to install the cable end.
Attach the casing cap.
Install at the gray casing cap side.
72666B
5.INSTALL REAR SEAT LOCK COVER LH
Attach the claw and guide to install the rear seat lock cover LH.
71879C
6.INSTALL REAR SEAT INNER RECLINING COVER LH
|
Install in this Direction |
Attach the claw to install the rear seat inner reclining cover LH.
71878B
7.INSTALL REAR SEAT INNER RECLINING COVER RH
Attach the guide.
Install the rear seat inner reclining cover RH with screw.
71879B
8.INSTALL REAR SEAT INNER RECLINING COVER LH
Attach the claw to install the rear seat inner reclining cover LH.
71878A
9.INSTALL REAR SEAT INNER RECLINING COVER RH
Attach the claw and guide to install the rear seat inner reclining cover RH.
71876
10.INSTALL RECLINING ADJUSTER INSIDE COVER LH
Attach the claw and guide to install the reclining adjuster inside cover LH.
71875B
11.INSTALL RECLINING ADJUSTER INSIDE COVER RH
Attach the claw and guide to install the reclining adjuster inside cover RH.
12.INSTALL SEAT COVER WIRE
Install the seat cover wire.
Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.
When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.
Make sure to read the precautions before preparing the wire.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION
| A | 130 mm (5.12 in.) |
| B | 270 mm (10.63 in.) |
| C | 290 mm (11.42 in.) |
The dimensions shown in the illustration are the lengths.
79012
13.INSTALL NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY LH
When installing the No. 1 seat cushion cover sub-assembly LH, refer to the precautions in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION
Align the seam allowance in a single direction as shown in the illustration.
Set the No. 1 seat cushion cover sub-assembly LH.
| *1 | Hog Ring Pliers |
| *a | Cutout |
Using hog ring pliers, install the No. 1 seat cushion cover sub-assembly LH to the No. 1 seat cushion pad LH with 14 new hog rings in the order indicated in the illustration.
Be careful not to damage the No. 1 seat cushion cover sub-assembly LH.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seat cushion cover sub-assembly LH.
Install the hog rings at the cutouts if they are there.
| *1 | Hog Ring Pliers |
Using hog ring pliers, connect the 3 straps of the No. 1 seat cushion cover sub-assembly LH to the No. 1 seat cushion pad LH with 3 new hog rings.
Be careful not to damage the No. 1 seat cushion cover sub-assembly LH.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seat cushion cover sub-assembly LH.
14.INSTALL SEAT CUSHION COVER WITH PAD
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Push in installation direction (1) shown in the illustration to temporarily install the seat cushion cover with pad.
Install the seat cushion cover with pad in the installation direction (2) so that the rear end is held in place.
Move the No. 1 seatback frame sub-assembly LH in the direction indicated by the arrow shown in the illustration.
73330C
15.INSTALL REAR CENTER SEAT LAP TYPE BELT ASSEMBLY RH
| *a | Band |
| *b | Wire Harness |
Connect the rear center seat lap type belt assembly RH to the band as shown in the illustration.
| *a | Slit |
| *b | Wire Harness |
Pass the wire harness through the slit.
Pass the rear center seat lap type belt assembly RH through the hole of the rear seat cushion cover with pad LH as shown in the illustration.
| *a | Protruding Part |
| *b | Wire Harness |
| *c | Anchor Part |
Install the rear center seat lap type belt assembly RH with the bolt.
The anchor part of the rear center seat lap type belt assembly RH must not overlap the protruding part.
The anchor part of the rear center seat lap type belt assembly RH must not overlap the protruding part.
Pass the wire harness underneath the anchor part.
Attach the clamp.
73340C
16.INSTALL REAR CENTER SEAT LAP TYPE BELT ASSEMBLY LH
|
Install in this Direction |
Pass the rear center seat lap type belt assembly LH through the hole of the rear seat cushion cover with pad LH as shown in the illustration.
| *a | Protruding Part |
Install the rear center seat lap type belt assembly LH with the bolt.
The anchor part of the rear No. 1 seat inner belt assembly LH must not overlap the protruding part.
Attach the clamp.
|
Connector |
|
A |
Pass the wire harness through the frame hole as shown in illustration A.
Connect the connector.
|
Install in this Direction |
While closing the back of the seat cushion cover with pad as shown in the illustration, pull out the rear seat lock assembly installation part of the rear No. 1 seat lock cable assembly and the rear center seat lap type belt assembly LH from the slit.
|
Install in this Direction |
Close the fasteners as shown in the illustration.
Push in the closed fasteners as shown in the illustration.
|
Install in this Direction | - | - |
Roll up the No. 1 fold seat stopper band assembly toward the rear end of the seat cushion with pad and push it into the seat cushion with pad in the direction indicated by the arrow shown in the illustration.
While sliding the part in the direction indicated by the arrow shown in the illustration, install the J hook.
72170
17.INSTALL REAR SEAT OUTER TRACK ASSEMBLY LH
Temporarily install the rear seat outer track assembly LH with the 2 bolts until it contacts the part.
|
Install in this Direction |
Slide the rail and install the rear seat outer track assembly LH with the bolt as shown in the illustration.
72190
18.INSTALL REAR SEAT INNER TRACK ASSEMBLY LH
Temporarily install the rear seat inner track assembly LH with the 2 bolts until it contacts the part.
|
Install in this Direction |
Slide the rail and install the rear seat inner track assembly LH with the bolt as shown in the illustration.
72201B
19.INSTALL SEAT TRACK HANDLE SUB-ASSEMBLY LH
Push in the seat track handle sub-assembly LH to attach the lock spring and install the seat track handle sub-assembly as shown in the illustration.
| *1 | Seat Track Handle Sub-Assembly LH | *2 | Lock Spring |
|
Install in this Direction | - | - |
Slide the rear seat inner track assembly LH and rear seat outer track assembly in the direction indicated by the arrow shown in the illustration and install them with the 4 bolts.
Attach the claw.
72660F
20.INSTALL REAR SEAT LOCK ASSEMBLY LH
Using a T55 "TORX" socket wrench, install the 2 "TORX" bolts and rear seat lock assembly LH.
| *1 | Cable End |
|
Install in this Direction |
Turn the cable end in the installation direction shown in the illustration to install the cable end.
Attach the casing cap.
Install at the purple casing cap side.
72660F
21.INSTALL REAR SEAT LOCK ASSEMBLY LH
Using a T55 "TORX" socket wrench, install the 2 "TORX" bolts and rear seat lock assembly LH.
Attach the hook.
| *1 | Cable End |
|
Install in this Direction |
Turn the cable end in the installation direction shown in the illustration to install the cable end.
Attach the casing cap.
Install at the yellow casing cap side.
79106
22.INSTALL NO. 1 SEAT LEG SUB-ASSEMBLY LH
Install the No. 1 seat leg sub-assembly LH with 4 bolts.
72666B
23.INSTALL REAR SEAT LOCK COVER LH
Attach the guide.
Attach the clip to install the rear seat lock cover LH.
72666B
24.INSTALL REAR SEAT LOCK COVER LH
Attach the guide.
Attach the clip to install the rear seat lock cover LH.
72618
25.INSTALL REAR SEATBACK LOCK STRIKER PROTECTOR
Attach the claw and clip to install the rear seatback lock striker protector.
72616A
26.INSTALL REAR SEATBACK LOCK STRIKER COVER LH
Attach the clamp.
Attach the claw and clip to install the rear seatback lock striker cover LH.
72618
27.INSTALL REAR SEATBACK LOCK STRIKER PROTECTOR
Attach the claw and clip to install the rear seatback lock striker protector.
72616A
28.INSTALL REAR SEATBACK LOCK STRIKER COVER LH
Attach the claw and clip to install the rear seatback lock striker cover LH.
Move the No. 1 seatback frame sub-assembly LH in the direction indicated by the arrow shown in the illustration.
29.INSTALL SEAT COVER WIRE
Install the seat cover wire.
Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.
When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.
Make sure to read the precautions before preparing the wire.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION
| A | 270 mm (10.63 in.) |
| B | 290 mm (11.42 in.) |
The dimensions shown in the illustration are the lengths.
79014
30.INSTALL NO. 1 SEATBACK COVER SUB-ASSEMBLY LH
When installing the No. 1 seatback cover sub-assembly LH, refer to the precautions in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION
Align the seam allowance in a single direction as shown in the illustration.
Set the No. 1 seatback cover sub-assembly LH.
| *1 | Hog Ring Pliers |
| *a | Cutout |
Using hog ring pliers, install the No. 1 seatback cover sub-assembly LH to the No. 1 seatback pad LH with 6 new hog rings in the order indicated in the illustration.
Be careful not to damage the No. 1 seatback cover sub-assembly LH.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly LH.
Install the hog rings at the cutouts if they are there.
| *1 | Hog Ring Pliers |
Using hog ring pliers, connect the 3 straps of the No. 1 seatback cover sub-assembly LH to the No. 1 seatback pad LH with 6 new hog rings.
Be careful not to damage the No. 1 seatback cover sub-assembly LH.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly LH.
31.INSTALL SEATBACK COVER WITH PAD
|
Install in this Direction (1) |
|
Install in this Direction (2) |
|
Install in this Direction (3) |
While aligning the top, push in the seatback cover with pad in the installation direction (1).
Push in the bottom left side of the seatback cover with pad in the installation direction (2).
Pass the installation part of the rear seat center armrest assembly shown by the arrow through the slit.
Push in the bottom right side of the seatback cover with pad in the installation direction (3).
While sliding the part in the direction indicated by the arrow shown in the illustration, install the J hook.
71931B
32.INSTALL REAR SEAT NO. 1 HEADREST SUPPORT ASSEMBLY
|
Install in this Direction |
Push in the installation direction shown in the illustration to attach the claw and install the 4 rear seat No. 1 headrest support assemblies.
|
Install in this Direction |
Close the fasteners as shown in the illustration.
Push in the fasteners as shown in the illustration.
|
Install in this Direction | - | - |
While sliding the part in the direction indicated by the arrow shown in the illustration, attach the J hook.
72830
33.INSTALL REAR SEAT CENTER ARMREST ASSEMBLY
Set the plate.
While pushing the plate in the installation direction (1), attach the guide.
| *1 | Stopper Pin | - | - |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
While aligning the stopper pin position of the rear seat center armrest assembly, install the plate in the installation direction (2).
Install the rear seat center armrest assembly with bolt.
71844E
34.INSTALL REAR SEAT RECLINING COVER LH
|
Install in this Direction |
Push the rear seat reclining cover LH as shown in the illustration to attach the claw and install the rear seat reclining cover LH.
71844D
35.INSTALL REAR SEAT RECLINING COVER LH
Attach the claw and guide.
Install the rear seat reclining cover LH with screw.
72526E
36.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
| *1 | Snap Ring |
|
Install in this Direction |
Install the snap ring to the reclining adjuster release handle LH.
Push the reclining adjuster release handle LH as shown in the illustration to attach the guide and install the reclining adjuster release handle LH.
71940A
37.INSTALL REAR SEAT HEADREST ASSEMBLY
|
Apply Silicon |
Apply silicon lubricant in this range.
Install rear seat headrest assembly.
71960B
38.INSTALL REAR SEAT CENTER HEADREST ASSEMBLY
|
Apply Silicon |
Apply silicon lubricant in this range.
Install rear seat center headrest assembly.