Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY
RM3270E _58 Vehicle Interior _041711 SEAT _0203011 REAR NO. 2 SEAT ASSEMBLY A

SEAT  REAR NO. 2 SEAT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·
B394717

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.

·

Replace any other damaged parts as necessary.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the RH side.



PROCEDURE

Hide 71940E 1.REMOVE NO.2 SEAT HEADREST ASSEMBLY

a.

Remove the No. 2 seat headrest assembly.


Hide 72927 2.REMOVE REAR SEAT CUSHION UNDER COVER RH

a.

Set the rear No. 2 seat assembly RH to the upright position.


b.
B402159

Remove the 2 hole plugs.


c.
B402160C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the remove direction to detach the clip to remove the rear seat cushion under cover RH.


Hide 71848D 3.REMOVE SEAT ADJUSTER COVER CAP RH

a.
B402162C01
0,0 0,0 false
V113147

Remove in this Direction


Lock the rear No. 2 seat leg assembly RH to the floor striker and set the rear No. 2 seat to the upright position.


b.

Using moulding remover A, lift in the direction indicated by the arrow shown in the illustration and pull in the removal direction to detach the claw and guide to remove seat adjuster cover cap RH.


Hide 4.REMOVE REAR NO. 2 SEAT ASSEMBLY RH

a.

Install stopper bolt in that order, as shown in the illustration.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)

NOTICE:

For the stopper bolts, use replacement parts (72702-0K220) or bolts which conform to the appropriate measurements (M8 x 1.25)


HINT:

The dimensions of each part of the stopper bolt are shown in the following chart.


Part Dimension
A 14 mm
B 24 mm or less
C 9 mm or less
D 45.4 mm
E 33.1 mm
F 1 mm or less (all around)
G 2.5 mm or less
H M8 x 1.25
I 10.5 mm or more
J 4 mm or more
K 22 mm or more
L 12 mm

B411383N01
5.073,0.115 5.229,0.313 0.156,0.198 10 false A 4.385,1.073 4.542,1.271 0.156,0.198 10 false B 4.167,1.792 4.323,1.99 0.156,0.198 10 false C 5.125,1.802 5.281,2 0.156,0.198 10 false D 4.885,2.083 5.042,2.281 0.156,0.198 10 false E 5.667,2.385 5.823,2.583 0.156,0.198 10 false G 5,2.521 5.156,2.719 0.156,0.198 10 false F 4.177,2.333 4.333,2.531 0.156,0.198 10 false J 4.51,2.719 4.667,2.917 0.156,0.198 10 false L 3.479,3.01 3.635,3.208 0.156,0.198 10 false K 6.479,3.031 6.635,3.229 0.156,0.198 10 false I 6.688,3.042 6.844,3.24 0.156,0.198 10 false H


b.
B402164

Remove the 3 bolts.


c.

Remove the 2 pop-up prevention bolts and rear No. 2 seat assembly RH.

NOTICE:
·

Protect the front seat legs.


·

Do not damage the rear No. 2 seat assembly RH, body exterior or interior parts.