Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
Replace any other damaged parts as necessary.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the RH side.
71693
1.REMOVE REAR SEAT LOWER CUSHION HINGE COVER RH
|
Remove in this Direction |
Remove the screw.
Pull up in removal direction shown in the illustration to detach the claw and guide and remove the rear seat lower cushion hinge cover RH.
72525D
2.REMOVE NO. 2 RECLINING ADJUSTER RELEASE HANDLE RH
| *1 | Rear Seatback Lock Release Button |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the rear seatback lock release button.
Pull the No. 2 reclining adjuster release handle RH in the removal direction (1) to pull it out of the rear seat lower cushion hinge cover RH.
Pull and remove the No. 2 reclining adjuster release handle RH in the removal direction (2).
72525A
3.REMOVE RECLINING ADJUSTER RELEASE HANDLE RH
|
Remove in this Direction |
|
Protective Tape |
With the reclining adjuster release handle RH pulled up.
Using a thin-bladed screwdriver with its tip wrapped in protective tape, detach the claw and remove the reclining adjuster release handle RH while moving it in the removal direction shown in the illustration.
71843A
4.REMOVE REAR NO. 2 SEAT RECLINING COVER RH
Remove the screw.
|
Remove in this Direction |
Remove the screw.
Pull in remove direction (1) shown in the illustration to detach the claw and guide and remove the Rear No. 2 seat reclining cover RH.
79393
5.REMOVE REAR NO. 2 SEATBACK CUSHION
Remove the bolt and rear No. 2 seatback cushion.
71931C
6.REMOVE REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY
While sliding the part in the direction indicated by the arrow shown in the illustration to detach the J hook.
|
Remove in this Direction |
Detach the claw and pull in the removal direction shown in the illustration to remove the 2 rear No. 2 seat headrest support assemblies.
7.REMOVE SEATBACK COVER WITH PAD
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Pull out the rear end of the seatback cover with pad in removal direction (1) shown in the illustration.
Lift in removal direction (2) shown in the illustration to remove the seatback cover with pad.
79023
8.REMOVE NO. 2 SEATBACK COVER SUB-ASSEMBLY RH
Remove the 3 hog rings and No. 2 seatback cover sub-assembly RH.
9.REMOVE SEAT COVER WIRE
Remove the seat cover wire.
79952
10.REMOVE NO. 2 SEAT CUSHION COVER
Pull out the rear seat cushion lock hook sub-assembly RH from the rear end of the seat cushion cover with pad.
While sliding the part in the direction indicated by the arrow shown in the illustration to detach the J hook.
Remove the clip.
Remove the screw.
| *A | for Front Side |
Remove the 2 screws.
| *A | for Rear Side |
Remove the No. 2 seat cushion cover with 2 screws.
72065A
11.REMOVE REAR SEAT CUSHION LOCK HOOK SUB-ASSEMBLY RH
| *1 | Rear Seat Cushion Band RH. |
Remove the rear seat cushion band RH and rear seat cushion lock hook sub-assembly RH.
79378A
12.REMOVE NO. 3 SEAT CUSHION HINGE COVER RH
|
Remove in this Direction |
Detach the clip.
Pull up in remove direction shown in the illustration to detach the claw and guide and remove the No. 3 seat cushion hinge cover RH.
13.REMOVE SEAT CUSHION COVER WITH PAD
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Pull up both sides of the seat cushion cover with pad in the removal direction (1).
Lift up the front end of the seat cushion cover with pad in the removal direction (2) to remove it.
79021
14.REMOVE NO. 2 CUSHION COVER SUB-ASSEMBLY RH
Remove the 6 hog rings and disconnect the 2 straps of the No. 2 cushion cover sub-assembly RH from the No. 2 seat cushion pad RH.
Remove the 8 hog rings and No. 2 cushion cover sub-assembly RH.
15.REMOVE SEAT COVER WIRE
Remove the seat cover wire.
71693
16.REMOVE REAR SEAT LOWER CUSHION HINGE COVER RH
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
While rotating the part in removal direction (1) shown in the illustration, detach the claw.
While rotating the part in removal direction (2) shown in the illustration, detach the claw and remove the rear seat lower cushion hinge cover RH.
79117A
17.REMOVE REAR NO. 2 SEAT CUSHION CARPET RH
|
Remove in this Direction |
Move the rear No. 2 seat leg assembly RH as shown in the illustration.
Detach the clip and remove the rear No. 2 seat cushion carpet RH.
73580A
18.REMOVE REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY
79030B
19.REMOVE REAR NO. 2 SEAT LEG ASSEMBLY RH
| *1 | Protective Tape |
|
Remove in this Direction |
Move a screwdriver with its tip wrapped with protective tape in the direction indicated by the arrow to widen and remove the 3 wiring harness clamps as shown in the illustration.
| *1 | Cable End |
|
Remove in this Direction |
for RH side:
Detach the casing cap.
Turn the cable end in the removal direction shown in the illustration and disconnect the cable end.
| *1 | Cable End |
|
Remove in this Direction |
for LH side:
Detach the casing cap.
Turn the cable end in the removal direction shown in the illustration and disconnect the cable end.
| *1 | Protective Tape |
|
Remove in this Direction |
Move a screwdriver with its tip wrapped with protective tape in the direction indicated by the arrow to widen and remove the hook of the spring clamp as shown in the illustration.
Remove the 2 bolts and rear No. 2 seat leg assembly RH.
79236A
20.REMOVE NO. 2 SEAT LEG COVER
| *1 | Protective Tape |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Using a screwdriver with its tip wrapped with protective tape, pry the No. 2 seat leg cover in the removal direction (1) to detach the guide and clip.
Pry in the removal direction (2) to detach the claw and remove the No. 2 seat leg cover.
72695B
21.REMOVE REAR SEAT LOCK CONTROL CABLE RH
|
Protective Tape |
Move a screwdriver with its tip wrapped with protective tape in the direction indicated by the arrow shown in the illustration to remove the spring.
Detach the clamp.
| *1 | Cable End |
|
Remove in this Direction |
Detach the casing cap.
Turn the cable end in the removal direction shown in the illustration and disconnect the cable end to remove the rear seat lock control cable RH.
71691B
22.REMOVE REAR OUTER SEAT LOCK COVER RH
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Pull in the removal direction (1) shown in the illustration to detach the guide.
Pull in the removal direction (2) shown in the illustration to remove the rear outer seat lock cover RH.
71303B
23.REMOVE REAR NO. 2 SEAT HINGE SUB-ASSEMBLY RH
|
Remove in this Direction |
Remove the 2 bolts.
Pull in the removal direction shown in the illustration to remove the rear No. 2 seat hinge sub-assembly RH.
Remove the spring carefully, as it is still under tension.
79203A
24.REMOVE NO. 2 SEATBACK FRAME SUB-ASSEMBLY RH
| *A | for RH side |
| *B | for LH side |
Using a T55 "TORX" socket wrench, remove the 4 "TORX" bolts and rear No. 2 seat hinge sub-assembly RH.