Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
63489
1.INSTALL REAR ROOF RACK LEG CUSHION LH
Attach the claw to install the rear roof rack leg cushion LH.
Attach the guide to install the No. 3 roof carrier support LH.
Using a T30 "TORX" socket wrench, install the 2 screws.
63487A
2.INSTALL FRONT ROOF RACK LEG CUSHION LH
Attach the claw to install the front roof rack leg cushion LH.
Attach the guide to install the No. 1 roof carrier support LH.
Using a T30 "TORX" socket wrench, install the 2 screws.
63439A
3.INSTALL NO. 3 ROOF CARRIER SEAL LH
When installing the No. 3 roof carrier seal LH, heat the roof rack assembly LH using a heat light.
| Item | Temperature |
|---|---|
| Roof Rack Assembly LH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Clean the roof rack assembly LH.
Using a heat light, heat the roof rack assembly LH surface.
Remove the double-sided tape from the roof rack assembly LH.
Wipe off any tape adhesive residue with cleaner.
Install a new No. 3 roof carrier seal LH.
Using a heat light, heat the roof rack assembly LH.
Remove the peeling paper from the face of the No. 3 roof carrier seal LH.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the No. 3 roof carrier seal LH as shown in the illustration.
Press the No. 3 roof carrier seal LH firmly to install it.
63437A
4.INSTALL NO. 2 ROOF CARRIER SEAL
When installing the No. 2 roof carrier seal, heat the roof rack assembly LH using a heat light.
| Item | Temperature |
|---|---|
| Roof Rack Assembly LH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Clean the roof rack assembly LH.
Using a heat light, heat the roof rack assembly LH surface.
Remove the double-sided tape from the roof rack assembly LH.
Wipe off any tape adhesive residue with cleaner.
Install a new No. 2 roof carrier seal.
Using a heat light, heat the roof rack assembly LH.
Remove the peeling paper from the face of the No. 2 roof carrier seal.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the No. 2 roof carrier seal as shown in the illustration.
Press the No. 2 roof carrier seal firmly to install it.
63435F
5.INSTALL NO. 1 ROOF CARRIER SEAL
When installing the No. 1 roof carrier seal, heat the roof rack assembly LH using a heat light.
| Item | Temperature |
|---|---|
| Roof Rack Assembly LH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Clean the roof rack assembly LH.
Using a heat light, heat the roof rack assembly LH surface.
Remove the double-sided tape from the roof rack assembly LH.
Wipe off any tape adhesive residue with cleaner.
Install a new No. 1 roof carrier seal.
Using a heat light, heat the roof rack assembly LH.
Remove the peeling paper from the face of the No. 1 roof carrier seal.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the No. 1 roof carrier seal as shown in the illustration.
Press the No. 1 roof carrier seal firmly to install it.
63485
6.INSTALL CENTER ROOF RACK LEG CUSHION
Install the center roof rack leg cushion.
63444A
7.INSTALL ROOF RACK PROTECTOR LH
Install the roof rack protector LH.
63494
8.INSTALL REAR ROOF RACK LEG COVER LH
Attach the claw and guide to install a new rear roof rack leg cover LH.
63492
9.INSTALL FRONT ROOF RACK LEG COVER LH
Attach the claw and guide to install a new front roof rack leg cover LH.