The cooling unit with fan motor sub-assembly is operated by signals from the air conditioning amplifier. Rear blower motor speed signals are transmitted in accordance with changes in the duty ratio.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When the servo motor or air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
Check the operation by referring to the table below.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Blower Motor | Blower with fan motor sub-assembly | Min.: 0
Max.: 31 |
- |
| Tester Display |
|---|
| Blower Motor |
Blower with fan motor sub-assembly operates and changes speed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear blower with fan motor sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REAR BLOWER MOTOR>REMOVAL
Inspect the rear blower with fan motor sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REAR BLOWER MOTOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Air Conditioning Control Assembly) |
Disconnect the air conditioning control assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N35-6 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N35-1 (+B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N35 air conditioning control assembly connector.
Disconnect the G37 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N35-3 (SI) - G37-23 (RCRL) | Always | Below 1 Ω |
| N35-3 (SI) or G37-23 (RCRL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N31 rear blower with fan motor sub-assembly connector.
Disconnect the N35 air conditioning control assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N31-2 (B) - N35-2 (VM) | Always | Below 1 Ω |
| N31-1 (L) - Body ground | Always | Below 1 Ω |
| N31-2 (B) or N35-2 (VM) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Air Conditioning Control Assembly) |
Using an oscilloscope, check the waveform.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | N35-3 (SI) - Body ground |
| Tool Setting | 2 V/DIV., 500 μs/DIV. |
| Condition | ·
Engine switch on (IG) ·
Blower switch: LO |
Waveform is as shown in the illustration.
Waveform varies with the blower level.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER MOTOR CONTROLLER(for Rear Side)>REMOVAL
NG
Replace the air conditioning control assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER MOTOR CONTROLLER(for Rear Side)>REMOVAL
Check if the same malfunction recurs when the sonar function is operated.
Malfunction does not reoccur (returns to normal).
| Proceed to |
|---|
| OK |
| NG |
OK
NG