Home › Engine / Hybrid System › 1GD-FTV ENGINE MECHANICAL › ENGINE UNIT
RM3270E _51 Engine / Hybrid System _041672 1GD-FTV ENGINE MECHANICAL _0205129 ENGINE UNIT G

1GD-FTV ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13506 1.INSPECT NO. 1 CHAIN SUB-ASSEMBLY

a.
A345790C01
1.635,1.188 1.948,1.344 0.313,0.156 10 false *a 2.844,1.813 3.156,2.01 0.313,0.198 10 false 16 0.479,1.813 0.656,2.01 0.177,0.198 10 false 1 0.656,1.813 0.833,2.01 0.177,0.198 10 false 2 0.854,1.813 1.031,2.01 0.177,0.198 10 false 3 1.031,1.813 1.208,2.01 0.177,0.198 10 false 4 1.219,1.813 1.396,2.01 0.177,0.198 10 false 5 1.406,1.813 1.583,2.01 0.177,0.198 10 false 6
*a Measuring Point


Using a spring scale, pull the No. 1 chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 16 pins.

Maximum chain elongation:

144.7 mm (5.70 in.)


HINT:

Perform the measurement at 3 random places.


If the elongation is more than the maximum, replace the No. 1 chain sub-assembly.


Hide 13507 2.INSPECT NO. 2 CHAIN SUB-ASSEMBLY

a.
A345791C01
1.646,1.198 1.958,1.354 0.313,0.156 10 false *a 2.896,1.813 3.208,2.01 0.313,0.198 10 false 16 0.469,1.813 0.646,2 0.177,0.188 10 false 1 0.635,1.813 0.813,2 0.177,0.188 10 false 2 0.802,1.813 0.979,2 0.177,0.188 10 false 3 0.969,1.813 1.146,2 0.177,0.188 10 false 4 1.135,1.813 1.313,2 0.177,0.188 10 false 5 1.292,1.813 1.469,2 0.177,0.188 10 false 6
*a Measuring Point


Using a spring scale, pull the No. 2 chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 16 pins.

Maximum chain elongation:

121.6 mm (4.79 in.)


HINT:

Perform the measurement at 3 random places.


If the elongation is more than the maximum, replace the No. 2 chain sub-assembly.


Hide 13540 3.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
A347238C01
0.635,1.25 0.635,0.656 true 1.615,1.719 1.615,1.125 true 2.49,1.656 2.708,1.271 2.708,1.271 2.875,1.271 true 0.563,1.26 0.875,1.417 0.313,0.156 10 false *a 1.552,1.75 1.865,1.906 0.313,0.156 10 false *b 2.927,1.188 3.24,1.344 0.313,0.156 10 false *c
*a No. 1 Chain Tensioner Assembly Body
*b Spring
*c Plunger


·

When the pin is removed from the No. 1 chain tensioner assembly, the plunger and spring may come off of the No. 1 chain tensioner assembly body, but this is not a malfunction.

·

Before installing the plunger and spring to the No. 1 chain tensioner assembly body, check that they are free of foreign matter and not damaged.



a.
A346658C01
1.646,0.698 2.406,0.698 true 2.448,0.615 2.76,0.771 0.313,0.156 10 false *a
*a Plunger


Push the plunger and check that it moves smoothly.

If necessary, replace the No. 1 chain tensioner assembly.


Hide 13550 4.INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A345792C01
2.385,1.146 2.625,0.573 2.625,0.573 2.823,0.573 true 1.885,1.74 2.51,1.979 2.51,1.979 2.708,1.979 true 2.76,1.896 3.073,2.052 0.313,0.156 10 false *a 2.865,0.5 3.177,0.656 0.313,0.156 10 false *b
*a Stopper Plate
*b Plunger


Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.

If necessary, replace the No. 2 chain tensioner assembly.


Hide 13523 5.INSPECT CAMSHAFT TIMING SPROCKET

a.

Wrap the No. 2 chain sub-assembly around the camshaft timing sprocket.


b.
A345793

Using a vernier caliper, measure the camshaft timing sprocket diameter with the No. 2 chain sub-assembly.

Minimum sprocket with chain diameter:

97.79 mm (3.85 in.)


If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and camshaft timing sprocket.

HINT:

The vernier caliper must contact the No. 2 chain sub-assembly rollers for the measurement.



Hide 13521 6.INSPECT CRANKSHAFT TIMING SPROCKET

a.

Wrap the No. 1 chain sub-assembly around the crankshaft timing sprocket.


b.
A345794

Using a vernier caliper, measure the crankshaft timing sprocket diameter with the No. 1 chain sub-assembly.

Minimum sprocket with chain diameter:

71.26 mm (2.81 in.)


If the diameter is less than the minimum, replace the No. 1 chain sub-assembly and crankshaft timing sprocket.

HINT:

The vernier caliper must contact the No. 1 chain sub-assembly rollers for the measurement.



Hide 13613 7.INSPECT INJECTION PUMP DRIVE GEAR

a.

for No. 1 Chain Sub-assembly Side:

i.

Wrap the No. 1 chain sub-assembly around the injection pump drive gear.


ii.
A345796

Using a vernier caliper, measure the injection pump drive gear diameter with the No. 1 chain sub-assembly.

Minimum gear with chain diameter:

71.26 mm (2.81 in.)


If the diameter is less than the minimum, replace the No. 1 chain sub-assembly and injection pump drive gear.

HINT:

The vernier caliper must contact the No. 1 chain sub-assembly rollers for the measurement.




b.

for No. 2 Chain Sub-assembly Side:

i.

Wrap the No. 2 chain sub-assembly around the injection pump drive gear.


ii.
A345795

Using a vernier caliper, measure the injection pump drive gear diameter with the No. 2 chain sub-assembly.

Minimum gear with chain diameter:

52.32 mm (2.06 in.)


If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and injection pump drive gear.

HINT:

The vernier caliper must contact the No. 2 chain sub-assembly rollers for the measurement.




Hide 13559 8.INSPECT NO. 1 CHAIN TENSIONER SLIPPER

a.
A345797C01
3.052,1.135 3.365,1.292 0.313,0.156 10 false *a
*a Depth


Measure the depth of wear of the No. 1 chain tensioner slipper.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the No. 1 chain tensioner slipper.


Hide 9.INSPECT NO. 2 CHAIN TENSIONER SLIPPER

a.
A345798C01
3.042,1.125 3.354,1.281 0.313,0.156 10 false *a
*a Depth


Measure the depth of wear of the No. 2 chain tensioner slipper.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the No. 2 chain tensioner slipper.


Hide 13561 10.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A345799C01
2.885,1.042 3.198,1.198 0.313,0.156 10 false *a
*a Depth


Measure the depth of wear of the No. 1 chain vibration damper.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the No. 1 chain vibration damper.


Hide 13562 11.INSPECT NO. 2 CHAIN VIBRATION DAMPER

a.
A345800C01
3.042,1.146 3.354,1.302 0.313,0.156 10 false *a
*a Depth


Measure the depth of wear of the No. 2 chain vibration damper.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the No. 2 chain vibration damper.


Hide 13566B 12.INSPECT TIMING CHAIN GUIDE

a.
A343586C01
3.135,1.313 3.354,1.479 0.219,0.167 10 false *a
*a Depth


Measure the depth of wear of the timing chain guide.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the timing chain guide.


Hide 17111 13.INSPECT INTAKE MANIFOLD

a.
A345801

Using a precision straightedge and feeler gauge, measure the warpage of the surface where the intake manifold contacts the cylinder head sub-assembly.

Maximum warpage:

0.10 mm (0.00394 in.)


If the warpage is more than the maximum, replace the intake manifold.


Hide 17141 14.INSPECT EXHAUST MANIFOLD

a.
A345802

Using a precision straightedge and feeler gauge, measure the warpage of the surface where the exhaust manifold contacts the cylinder head sub-assembly.

Maximum warpage:

0.10 mm (0.00394 in.)


If the warpage is more than the maximum, replace the exhaust manifold.


Hide 13511 15.INSPECT CAMSHAFT

a.

Inspect the camshaft runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.00118 in.)


If the circle runout is more than the maximum, replace the camshaft.

HINT:

Check the oil clearance after replacing the camshaft.




b.

Inspect the cam lobes.

i.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

41.425 to 41.525 mm (1.631 to 1.635 in.)


Minimum cam lobe height:

41.375 mm (1.629 in.)


If the cam lobe height is less than the minimum, replace the camshaft.



c.

Inspect the camshaft journals.

i.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 34.449 to 34.465 mm (1.356 to 1.357 in.)
Other journals 22.990 to 23.007 mm (0.905 to 0.906 in.)


If the journal diameter is not as specified, check the oil clearance.



Hide 13512 16.INSPECT NO. 2 CAMSHAFT

a.

Inspect the No. 2 camshaft runout.

i.

Place the No. 2 camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.00118 in.)


If the circle runout is more than the maximum, replace the No. 2 camshaft.

HINT:

Check the oil clearance after replacing the No. 2 camshaft.




b.

Inspect the cam lobes.

i.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

41.694 to 41.794 mm (1.641 to 1.645 in.)


Minimum cam lobe height:

41.644 mm (1.640 in.)


If the cam lobe height is less than the minimum, replace the No. 2 camshaft.



c.

Inspect the No. 2 camshaft journals.

i.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 34.449 to 34.465 mm (1.356 to 1.357 in.)
Other journals 22.990 to 23.007 mm (0.905 to 0.906 in.)


If the journal diameter is not as specified, check the oil clearance.



Hide 17.INSPECT CAMSHAFT OIL CLEARANCE

a.

Clean the No. 1 camshaft bearing cap, No. 2 camshaft bearing caps, camshaft journals and No. 2 camshaft journals.


b.

Place the camshaft and No. 2 camshaft on the cylinder head sub-assembly.


c.
A347311C01
0.594,0.406 0.771,0.406 0.771,0.406 1.635,1.156 true 0.427,0.302 0.74,0.458 0.313,0.156 10 false *a
*a Plastigage


Lay a strip of Plastigage across each of the camshaft journals.


d.

Install the No. 1 camshaft bearing cap and No. 2 camshaft bearing caps to the cylinder head sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

NOTICE:

Do not turn the camshaft and No. 2 camshaft.



e.

Remove the No. 1 camshaft bearing cap and No. 2 camshaft bearing caps from the cylinder head sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY


f.
A347310

Measure the Plastigage at its widest point.

Standard Oil Clearance:
Item Specified Condition
No. 1 journal 0.040 to 0.077 mm (0.00157 to 0.00303 in.)
Other journals 0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Maximum Oil Clearance:
Item Specified Condition
No. 1 journal 0.117 mm (0.00461 in.)
Other journals 0.102 mm (0.00402 in.)


If the camshaft oil clearance is more than the maximum, replace the camshaft. If necessary, replace the cylinder head sub-assembly.


g.

Completely remove the Plastigage from the camshaft journals.


Hide 11101A 18.INSPECT CYLINDER HEAD SET BOLT

a.

w/ Washer:

i.
A345806C01
0.563,1.896 0.563,1.344 true 2.385,0.375 2.698,0.531 0.313,0.156 10 false *a 0.5,1.927 0.813,2.083 0.313,0.156 10 false *b
*a Measuring Area
*b Washer


Using a vernier caliper, measure the thread outside diameter of the cylinder head set bolt.

Minimum diameter:

11.4 mm (0.449 in.)


If the diameter is less than the minimum, replace the cylinder head set bolt.



b.

w/o Washer:

i.
A345805C01
2.625,0.385 2.938,0.542 0.313,0.156 10 false *a
*a Measuring Area


Using a vernier caliper, measure the thread outside diameter of the cylinder head set bolt.

Minimum diameter:

12.8 mm (0.504 in.)


If the diameter is less than the minimum, replace the cylinder head set bolt and cylinder head set bolt spacer.



Hide 13801 19.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Turn the roller by hand and check that it turns smoothly.

If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.


Hide 13750 20.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the adjuster free from dirt and foreign matter.

·

Use only clean engine oil.



a.

Place the valve lash adjuster assembly into a container full of new engine oil.

A345808C01
1.073,0.594 1.635,0.594 true 2.833,0.594 3.396,0.594 true 1.042,1.031 1.656,1.031 true 1.083,1.281 1.656,1.281 true 0.979,1.802 1.646,1.802 true 0.917,2.177 1.646,2.177 true 1.042,2.375 1.646,2.375 true 4.26,1.021 4.458,1.021 4.458,1.021 5.021,1.323 true 0.823,0.198 1.135,0.354 0.313,0.156 10 false *a 2.521,0.198 2.833,0.354 0.313,0.156 10 false *b 1.708,0.938 2.021,1.094 0.313,0.156 10 false *c 1.708,1.177 2.021,1.333 0.313,0.156 10 false *d 1.708,1.708 2.021,1.865 0.313,0.156 10 false *e 1.708,2.094 1.969,2.302 0.26,0.208 10 false *f 1.708,2.281 2,2.531 0.292,0.25 10 false *g 1.688,0.5 2.146,0.698 0.458,0.198 10 false SST 3.448,0.5 3.906,0.698 0.458,0.198 10 false SST 3.969,0.927 4.427,1.125 0.458,0.198 10 false SST
*a CORRECT *b INCORRECT
*c Taper Part *d Plunger
*e Low Pressure Chamber *f Check Ball
*g High Pressure Chamber - -



b.

Insert the tip of SST into the plunger and use the tip to press down on the check ball inside the plunger.

SST
09276-75010  


c.

Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding high-pressure air from the compression chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.



e.

After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.

OK:

Plunger is very difficult to move.


If the result is not as specified, replace the valve lash adjuster assembly.