The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the turbocharger sub-assembly removal/installation are shown below.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
25051
1.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
51410
2.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
3.DRAIN ENGINE COOLANT
4.DRAIN ENGINE OIL
17341F
5.REMOVE NO. 1 AIR HOSE
17344E
6.REMOVE NO. 4 AIR HOSE
17362B
7.REMOVE NO. 2 AIR TUBE
16571C
8.REMOVE NO. 1 RADIATOR HOSE
44360
9.DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY
44369A
10.REMOVE NO. 1 OIL RESERVOIR BRACKET
16470
11.REMOVE RADIATOR RESERVOIR
16711
12.REMOVE FAN SHROUD
17705
13.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE
Disconnect the mass air flow meter sub-assembly connector and detach the 2 harness clamps.
Detach the 4 clips.
Loosen the hose clamp and remove the air cleaner cap sub-assembly with air cleaner hose.
17801
14.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner element sub-assembly from the air cleaner case.
17701
15.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Disconnect the 3 wire harness clamps.
Remove the 3 bolts and air cleaner case sub-assembly.
16279
16.REMOVE NO. 3 WATER BY-PASS PIPE
Slide the 2 clips and disconnect the 2 water hoses from the oil cooler assembly and No. 2 water by-pass pipe.
Remove the bolt and No. 3 water by-pass pipe.
12261
17.REMOVE PCV HOSE
Slide the 2 clips.
Slide the 2 clips, detach the clamp and remove the PCV hose.
16268
18.REMOVE NO. 1 WATER BY-PASS PIPE
16284
19.DISCONNECT TURBO WATER HOSE
Slide the 2 clips and disconnect the No. 1 turbo water hose and No. 2 turbo water hose from the water outlet sub-assembly and water pump assembly.
20.DISCONNECT BRACKET OIL COOLER TUBE BRACKET AND WIRE HARNESS CLAMP BRACKET (for Automatic Transmission)
Remove the bolt and disconnect the oil cooler tube bracket.
Detach the 2 clamps and disconnect the wire harness.
21.DISCONNECT WIRE HARNESS CLAMP BRACKET (for Manual Transmission)
Remove the bolt, detach the clamp and disconnect the wire harness.
17293
22.REMOVE TURBOCHARGER STAY
Remove the 3 bolts, nut and the turbocharger stay.
15474
23.REMOVE TURBO OIL OUTLET PIPE
Slide the 2 clips and disconnect the turbo oil outlet hose from the turbo oil outlet pipe.
Remove the 2 bolts and turbo oil outlet pipe and gasket.
15407
24.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY
Remove the union bolt and gasket.
Remove the 2 nuts and the turbo oil inlet pipe sub-assembly.
Do not loosen the nut labeled A.
Remove the gasket.
17201
25.REMOVE TURBOCHARGER SUB-ASSEMBLY
Remove the 3 nuts and turbocharger sub-assembly.
Remove the gasket from the exhaust manifold.
25601
26.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY
17141
27.REMOVE EXHAUST MANIFOLD
Remove the 8 nuts, 8 plate washers, 8 collars and exhaust manifold.
Remove the gasket.
16027
28.REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY
Slide the 2 hose clips and disconnect the No. 1 turbo water hose and No. 2 turbo water hose from the turbo water pipe sub-assembly.
Remove the bolt.
Remove the 2 nuts, turbo water pipe sub-assembly and gasket.
17274
29.REMOVE COMPRESSOR INLET ELBOW
Remove the 2 bolts and compressor inlet elbow stay.
Remove the 2 nuts and compressor inlet elbow from turbocharger sub-assembly.
Using an E8 "TORX" socket wrench, remove the stud bolt shown in the illustration together with the compressor inlet elbow and gasket.
17275
30.REMOVE COMPRESSOR OUTLET ELBOW
Remove the 2 nuts and compressor outlet elbow.
Remove the gasket.
Remove the bolt and hose clamp.
31.REMOVE STUD BOLT
If a stud bolt is deformed or its threads are damaged, replace it.
Using an E5 "TORX" socket wrench, remove the 4 stud bolts shown in the illustration.
Using an E8 "TORX" socket wrench, remove the 4 stud bolts shown in the illustration.
Using an E10 "TORX" socket wrench, remove the 3 stud bolts shown in the illustration.