Home › Vehicle Interior › DOOR LOCK › DOOR CONTROL SWITCH › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041705 DOOR LOCK _0205679 DOOR CONTROL SWITCH G

DOOR LOCK  DOOR CONTROL SWITCH  INSPECTION  


PROCEDURE

Hide 84820 1.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

a.
B361186C09
2.177,3.615 2.469,3.021 true 2.406,4.375 2.177,3.927 true 2.333,0.583 2.333,0.25 2.333,0.25 0.417,0.25 true 2.135,0.417 2.135,0.25 true 1.5,0.833 1.5,0.25 true 1.333,0.688 1.333,0.25 true 0.865,1.052 0.875,0.25 true 0.542,0.917 0.542,0.365 0.542,0.365 0.542,0.25 true 0.667,1.146 0.667,0.25 true 2.542,2.906 2.844,3.104 0.302,0.198 10 false ILL+ 2.375,4.396 2.771,4.583 0.396,0.188 10 false ILL- 0.198,0.156 0.813,0.354 0.615,0.198 10 false *b 0.417,2.906 0.667,3.073 0.25,0.167 10 false *a
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)
*b LED Illumination


Check that the LED illuminates. (except Models with Jam Protection Function on Driver Door Window Only)

i.

Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Battery connection Result
Battery positive (+) - 3 (ILL+)
Battery negative (-) - 13 (ILL-)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



b.
B408987C01
1.333,0.844 1.333,0.271 true 0.542,1.073 0.542,0.271 true 0.677,1.313 0.677,0.271 true 0.875,1.219 0.875,0.271 true 0.542,0.271 1.771,0.271 false 2.677,4.24 2.479,4.24 2.479,4.24 2.229,3.802 true 1.781,3.51 2.031,2.74 2.031,2.74 2.344,2.74 true 1.833,0.188 2.146,0.385 0.313,0.198 10 false *b 2.385,2.677 2.854,2.896 0.469,0.219 10 false ILL- 2.729,4.167 3.198,4.385 0.469,0.219 10 false ILL+ 0.792,2.698 1.104,2.896 0.313,0.198 10 false *a
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)
*b LED Illumination


Check that the LED illuminates. (for Models with Jam Protection Function on Driver Door Window Only)

i.

Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Battery connection Result
Battery positive (+) - 17 (ILL+)
Battery negative (-) - 5 (ILL-)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



c.
B408989C01
0.667,1.302 0.667,0.448 0.667,0.448 0.5,0.448 true 0.865,1.229 0.865,0.375 0.865,0.375 1.063,0.375 true 1.333,3.521 1.333,2.583 1.333,2.583 1.594,2.583 true 2.229,3.521 2.229,2.583 2.229,2.583 2.49,2.583 true 2.438,3.563 2.771,3.563 true 0.302,0.354 0.615,0.552 0.313,0.198 10 false *a 1.115,0.302 1.427,0.5 0.313,0.198 10 false *b 1.646,2.51 1.917,2.708 0.271,0.198 10 false UL 2.542,2.51 2.813,2.708 0.271,0.198 10 false L 2.823,3.49 3.094,3.688 0.271,0.198 10 false E 0.833,2.646 1.146,2.844 0.313,0.198 10 false *c
*a Lock
*b Unlock
*c Component without harness connected
(Power Window Regulator Master Switch Assembly)


Measure the resistance according to the value(s) in the table below. (w/o Smart Entry and Start System)

Standard Resistance:
Tester Connection Condition Specified Condition
8 (L) - 9 (E) Lock switch pushed Below 1 Ω
8 (L) - 9 (E) Lock switch not pushed 10 kΩ or higher
2 (UL) - 9 (E) Unlock switch pushed Below 1 Ω
2 (UL) - 9 (E) Unlock switch not pushed 10 kΩ or higher


If the result is not as specified, replace the power window regulator master switch assembly.