Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041705 DOOR LOCK _0205680 FRONT DOOR LOCK G

DOOR LOCK  FRONT DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69310 1.INSPECT FRONT DOOR LOCK ASSEMBLY RH

a.
B340409C06
1.24,3.521 0.792,3.521 true 2.167,3.521 2.563,3.521 true 1.938,4.177 1.75,3.823 true 1.594,3.813 1.375,4.167 true 1.115,2.052 1.427,2.25 0.313,0.198 10 false *a 1.698,2.469 2.01,2.667 0.313,0.198 10 false *b 0.844,2.854 1.156,3.052 0.313,0.198 10 false *c 0.688,3.448 0.844,3.646 0.156,0.198 10 false L 2.646,3.448 2.958,3.646 0.313,0.198 10 false UL 1.844,4.229 2.458,4.427 0.615,0.198 10 false LSSR 1.292,4.208 1.448,4.406 0.156,0.198 10 false E
*a Unlock
*b Lock
*c Component without harness connected
(Front Door Lock Assembly RH)


Check the door lock motor operation.

i.

Apply battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock


If the result is not as specified, replace the front door lock assembly RH.



b.

Check the resistance of the door unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (LSSR) - 8 (E) Lock 10 kΩ or higher
7 (LSSR) - 8 (E) Unlock Below 1 Ω


If the result is not as specified, replace the front door lock assembly RH.



c.
B340408C12
1.969,3.813 2.156,4.219 true 1.604,3.792 1.49,4.198 true 2.177,3.76 2.552,3.76 true 0.604,0.531 0.917,0.729 0.313,0.198 10 false *a 0.406,0.958 0.719,1.156 0.313,0.198 10 false *b 0.635,1.406 0.948,1.604 0.313,0.198 10 false *c 0.792,2.865 1.104,3.063 0.313,0.198 10 false *d 2.604,3.646 2.917,3.844 0.313,0.198 10 false UL 2.146,4.26 2.302,4.458 0.156,0.198 10 false L 1.417,4.25 1.573,4.448 0.156,0.198 10 false E
*a Unlock
*b Neutral
*c Lock
*d Component without harness connected
(Front Door Lock Assembly RH)


Check the resistance of the door key lock and unlock switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (L) - 8 (E) Held to lock side Below 1 Ω
6 (L) - 8 (E)
5 (UL) - 8 (E)
Neutral 10 kΩ or higher
5 (UL) - 8 (E) Held to unlock side Below 1 Ω


If the result is not as specified, replace the front door lock assembly RH.



Hide 69320 2.INSPECT FRONT DOOR LOCK ASSEMBLY LH

a.
B380493C01
1.24,3.521 0.823,3.521 true 2.156,3.521 2.604,3.521 true 1.802,3.823 1.927,4.125 true 1.615,3.813 1.427,4.156 true 2.208,2.083 2.521,2.24 0.313,0.156 10 false *a 1.635,2.49 1.948,2.646 0.313,0.156 10 false *b 0.813,2.813 1.125,2.969 0.313,0.156 10 false *c 0.698,3.438 0.854,3.635 0.156,0.198 10 false L 2.677,3.448 2.99,3.646 0.313,0.198 10 false UL 1.927,4.177 2.083,4.375 0.156,0.198 10 false E 1.25,4.198 1.865,4.396 0.615,0.198 10 false LSSR
*a Unlock
*b Lock
*c Component without harness connected
(Front Door Lock Assembly LH)


Check the door lock motor operation.

i.

Apply battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Lock
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlock


If the result is not as specified, replace the front door lock assembly LH.



b.

Check the resistance of the door unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (E) - 8 (LSSR) Lock 10 kΩ or higher
Unlock Below 1 Ω


If the result is not as specified, replace the front door lock assembly LH.