Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM3270E _59 Vehicle Exterior _041717 DOOR / HATCH _0205696 POWER BACK DOOR SYSTEM U

DOOR / HATCH  POWER BACK DOOR SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Back Door or Entry & Start / Data List.


f.

According to the display on the GTS, read the Data List.

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Lock Status Back door condition signal Lock or Unlock Lock: Back door locked
Unlock: Back door unlocked
-
Half Latch SW Half latch switch signal ON or OFF ON: Back door lock motor open-latched
OFF: Back door lock motor full-latched or half-latched
Refer to "POWER BACK DOOR OPERATION TIMING CHART"*1
Closer Position SW Initial switch signal ON or OFF ON: Back door lock sector gear in center position (Initial switch on)
OFF: Back door lock sector gear out of center position (Initial switch off)
Refer to "POWER BACK DOOR OPERATION TIMING CHART"*1
Pawl Position Switch Pawl switch signal ON or OFF ON: Back door lock motor open-latched
OFF: Back door lock motor except open-latched
Refer to "POWER BACK DOOR OPERATION TIMING CHART"*1
Courtesy SW Back door courtesy switch signal ON or OFF ON: Back door open
OFF: Back door closed
Refer to "POWER BACK DOOR OPERATION TIMING CHART"*1
PBD Touch Sensor (Right) Power back door sensor assembly RH signal ON, OFF or Open ON: Power back door sensor assembly RH pressed
OFF: Power back door sensor assembly RH not pressed
Open: Power back door sensor assembly RH circuit open
-
PBD Touch Sensor (Left) Power back door sensor assembly LH signal ON, OFF or Open ON: Power back door sensor assembly LH pressed
OFF: Power back door sensor assembly LH not pressed
Open: Power back door sensor assembly LH circuit open
-
PBD Main SW Power back door main switch signal ON or OFF ON: Power back door main switch pushed
OFF: Power back door main switch not pushed
-
PBD Close SW Back door control switch signal ON or OFF ON: Back door control switch pushed
OFF: Back door control switch not pushed
-
IG SW Engine switch signal ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
"OFF" is also displayed for this item when the engine switch is on (ACC).
PBD Position (3/4-Open) Load signal detected during back door closing operation (3/4 - Open) Caution or OK Caution: Load detected between back door 3/4 and fully open position during back door closing operation
OK: No load detected between back door 3/4 and fully open position during back door closing operation
-
PBD Position (2/4-3/4) Load signal detected during back door closing operation (2/4 - 3/4) Caution or OK Caution: Load detected between back door 2/4 and 3/4 open position during back door closing operation
OK: No load detected between back door 2/4 and 3/4 open position during back door closing operation
-
PBD Position (1/4-2/4) Load signal detected during back door closing operation (1/4 - 2/4) Caution or OK Caution: Load detected between back door 1/4 and 2/4 open position during back door closing operation
OK: No load detected between back door 1/4 and 2/4 open position during back door closing operation
-
PBD Position (Close-1/4) Load signal detected during back door closing operation (Close - 1/4) Caution or OK Caution: Load detected between back door fully closed and 1/4 open position during back door closing operation
OK: No load detected between back door fully closed and 1/4 open position during back door closing operation
-
Closed Position Initialization Back door fully closed position memorized signal Not Initialized or Initialized Not Initialized: Back door fully closed position not memorized
Initialized: Back door fully closed position memorized
-
PBD SW Operation Power back door switch operation ON or 0.8 s Current customize setting displayed -
PBD Buzz In Use Power back door warning buzzer operation condition signal OFF or ON Current customize setting displayed The warning buzzer that sounds when the power back door is operating cannot be customized (even if this function is set to "OFF", the buzzer will still sound).
PBD Assist Open Operation Function that enables or disables the power back door assist open operation. When PBD Assist Open is set to on (enabled) the back door will open automatically when the back door opener switch assembly (opener switch) is operated. OFF or ON Current customize setting displayed -
PBD Assist Close Operation Function that enables or disables the power back door assist close operation. When PBD Assist Close is set to on (enabled) the back door will close automatically when the back door is closed by hand. OFF or ON Current customize setting displayed -
Door Unlock with 1 Motion. Door or doors to be unlocked when back door locked and power back door operated by pressing electrical key transmitter sub-assembly (power back door button)/Back Door or ALL DOORS.*2 Back Door or ALL DOORS Current customize setting displayed Not applicable
Wireless Power Back Door Open Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly).*3 Lock:OFF/Unlock:OFF, Lock:OFF/Unlock:ON, Lock:OFF/Unlock:Twice, Lock:OFF/Unlock:0.8s, Lock:Twice/Unlock:Twice or Lock:0.8s/Unlock:0.8 Current customize setting displayed -
Power Back Door Opening Adjust Function that can be used to set the power back door opening angle at 5 different positions. Min, Small, Middle, Large or Max Current customize setting displayed -
#Codes Number of DTCs Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0
-
HINT:

*1: Refer to "POWER BACK DOOR OPERATION TIMING CHART"

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>SYSTEM DESCRIPTION

*2: Although the item is displayed on the GTS, it is not applicable to this vehicle.

*3: "Lock:Twice/Unlock:Twice" and "Lock:0.8s/Unlock:0.8s" are not applicable to this vehicle.



Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tr/B-Door Unlock SW Back door opener switch assembly (open switch) signal ON or OFF ON: Back door opener switch assembly (open switch) on
OFF: Back door opener switch assembly (open switch) off
-


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Back Door / Active Test.


f.

Perform the "Active Test" according to the display on the GTS.

Body Electrical > Back Door > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Latch Release Latch release operation ON or OFF -
PBD Open/Close Power back door motor operation Forward, Reverse or OFF -
PBD Buzzer Power back door warning buzzer sound ON or OFF -