Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM3270E _59 Vehicle Exterior _041717 DOOR / HATCH _0205696 POWER BACK DOOR SYSTEM C

DOOR / HATCH  POWER BACK DOOR SYSTEM  B2228  PBD Unit Motor LH Circuit  


DESCRIPTION

This DTC is output when the multiplex network door ECU detects a power back door unit assembly set LH motor malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2228 PBD Unit Motor LH Circuit Multiplex network door ECU detects power back door unit assembly set LH motor malfunction
·

Multiplex network door ECU

·

Power back door unit assembly set LH

·

Harness or connector



WIRING DIAGRAM

E365367E01
4.469,1.625 4.927,1.823 0.458,0.198 10 false V13 4.458,1.802 7.156,2.219 2.698,0.417 10 false Multiplex Network Door ECU 1.177,1.646 1.635,1.844 0.458,0.198 10 false V16 1.188,1.833 2.563,2.188 1.375,0.354 10 false Power Back Door Unit Assembly Set LH 2,0.688 2.458,0.885 0.458,0.198 10 false BD+ 4.625,0.813 5.083,1.01 0.458,0.198 10 false BD+ 4.646,1.323 5.104,1.521 0.458,0.198 10 false BD- 2.052,1.208 2.51,1.406 0.458,0.198 10 false BD- 2.427,0.573 2.583,0.771 0.156,0.198 10 false 1 2.438,1.083 2.594,1.281 0.156,0.198 10 false 2 4.396,1.094 4.552,1.292 0.156,0.198 10 false 4 4.396,0.552 4.552,0.75 0.156,0.198 10 false 3 5.208,0.948 5.667,1.146 0.458,0.198 10 false CPU

CAUTION / NOTICE / HINT

NOTICE:

If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Back Door > Clear DTCs
50002 159

b.

Check for DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Back Door > Trouble Codes
50001 159
OK:

DTC B2228 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT POWER BACK DOOR UNIT ASSEMBLY SET LH
2.INSPECT POWER BACK DOOR UNIT ASSEMBLY SET LH
a.

Fully open the back door.


b.
E357428C01
1.938,0.75 2.25,0.51 true 1.479,0.74 1.146,0.573 true 0.146,0.146 0.458,0.302 0.313,0.156 10 false *a 0.802,0.448 1.115,0.604 0.313,0.156 10 false BD+ 2.323,0.427 2.635,0.583 0.313,0.156 10 false BD-
*a Component without harness connected
(Power Back Door Unit Assembly Set LH)


Disconnect the power back door unit assembly set LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (BD+) - Body ground Always 10 kΩ or higher
2 (BD-) - Body ground Always 10 kΩ or higher
1 (BD+) - 2 (BD-) Always Below 1 MΩ



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY SET LH)

NG

REPLACE POWER BACK DOOR UNIT ASSEMBLY SET LH

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY SET LH)
a.

Disconnect the V13 multiplex network door ECU connector.


b.

Disconnect the V16 power back door unit assembly set LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V13-3 (BD+) - V16-1 (BD+) Always Below 1 Ω
V13-4 (BD-) - V16-2 (BD-) Always Below 1 Ω
V13-3 (BD+) or V16-1 (BD+) - Body ground Always 10 kΩ or higher
V13-4 (BD-) or V16-2 (BD-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR