When the defogger switch on the air conditioning control assembly is pressed, the operation signal is transmitted to the air conditioning amplifier assembly via LIN communication. When the air conditioning amplifier assembly receives the signal, it turns on the DEFOGGER relay to operate the window defogger system.
Inspect the fuses for circuits related to this system before performing the following procedure.
The window defogger system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the window defogger system after confirming that the communication system is functioning properly.
Click hereVehicle Exterior>WINDOW / GLASS>WINDOW DEFOGGER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check the air conditioning system.
Both the window defogger system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly via the same communication line.
The air conditioning system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the defogger indicator illuminates when the defogger switch is on.
Defogger indicator illuminates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, perform the Active Test.
Click hereVehicle Exterior>WINDOW / GLASS>WINDOW DEFOGGER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Defogger Relay (Rear) | DEFOGGER relay | OFF or ON | - |
| Tester Display |
|---|
| Defogger Relay (Rear) |
Back window glass (defogger wire) warms up.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air conditioning amplifier assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
Check that the window defogger system operates normally.
The window defogger system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Back Door Glass [Defogger Wire]) |
Disconnect the back door glass (defogger wire) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Vb1-1 - Body ground | Ignition switch ON, defogger switch on | 11 to 14 V |
| Ignition switch ON, defogger switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the DEFOGGER relay from the No. 6 instrument panel relay block assembly.
Inspect the DEFOGGER relay.
Click hereVehicle Exterior>WINDOW / GLASS>RELAY(for Window Defogger)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to DEFOGGER Relay) |
Remove the DEFOGGER relay from the No. 6 instrument panel relay block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DEFOGGER relay terminal 1 - Body ground | Ignition switch ON | 11 to 14 V |
| DEFOGGER relay terminal 5 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the DEFOGGER relay from the No. 6 instrument panel relay block assembly.
Disconnect the G37 air conditioning amplifier assembly connector.
Disconnect the Vb1 back door glass (defogger wire) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DEFOGGER relay terminal 2 - G37-38 (RDFG) | Always | Below 1 Ω |
| DEFOGGER relay terminal 3 - Vb1-1 | Always | Below 1 Ω |
| DEFOGGER relay terminal 2 or G37-38 (RDFG) - Body ground | Always | 10 kΩ or higher |
| DEFOGGER relay terminal 3 or Vb1-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG