Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function)
RM3270E _58 Vehicle Interior _041706 THEFT DETERRENT / KEYLESS ENTRY _0212879 SMART ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  B27A8  Open in Outside Luggage Compartment Electrical Key Antenna Circuit  


DESCRIPTION

When the back door opener switch assembly is pressed, the certification ECU (smart key control ECU assembly) generates a request signal and sends it through the No. 2 indoor electrical key antenna assembly (back door).

The electrical key antenna transmits the received signal within an area of approximately 0.7 m (2.30 ft.) from the back door in order to detect the person carrying the electrical key transmitter sub-assembly.

DTC B27A8 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (back door) (between terminals CLG8 and ANTE8, or terminals CG8B and CLGB).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27A8 Open in Outside Luggage Compartment Electrical Key Antenna Circuit An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (back door) (CLG8 - ANTE8, CG8B - CLGB) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·

Harness or connector

·

No. 2 indoor electrical key antenna assembly (back door)

·

Certification ECU (smart key ECU assembly)


DTC Output Confirmation Operation:

Any time



*: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Vehicle Condition when Malfunction Detected
Entry lock/unlock operation cannot be performed for back door -

Related Data List and Active Test
DTC No. Data List and Active Test
B27A8 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B405295E05
5.094,2.573 6.604,3.146 1.51,0.573 10 false Certification ECU (Smart Key ECU Assembly) 4.938,2.021 5.25,2.229 0.313,0.208 10 false G17 4.948,0.865 5.26,1.073 0.313,0.208 10 false G17 6.5,2.021 6.813,2.229 0.313,0.208 10 false G16 6.531,1.802 6.844,2.01 0.313,0.208 10 false 10 5.823,1.177 6.135,1.385 0.313,0.208 10 false IC 5,1.771 5.313,1.979 0.313,0.208 10 false 24 5.031,0.635 5.344,0.844 0.313,0.208 10 false 8 5.302,0.75 6.063,1 0.76,0.25 10 false CLG8 5.313,1.885 6.073,2.135 0.76,0.25 10 false CG8B 1.313,1.927 2.073,2.177 0.76,0.25 10 false CLGB 1.229,0.771 2.073,1.021 0.844,0.25 10 false ANTE8 1.813,0.781 2.125,0.99 0.313,0.208 10 false 1 1.833,1.927 2.146,2.135 0.313,0.208 10 false 3 0.74,2.542 1.052,2.75 0.313,0.208 10 false V11 0.729,2.719 3.583,3.208 2.854,0.49 10 false No. 2 Indoor Electrical Key Antenna Assembly (Back Door) 6.292,2.021 7.052,2.271 0.76,0.25 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (back door).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (BACK DOOR))

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (BACK DOOR))
a.

Disconnect the G17 certification ECU (smart key ECU assembly) connector.


b.

Disconnect V11 No. 2 indoor electrical key antenna assembly (back door) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-8 (CLG8) - V11-1 (ANTE8) Always Below 1 Ω
G17-24 (CG8B) - V11-3 (CLGB) Always Below 1 Ω
G17-8 (CLG8) or V11-1 (ANTE8) - Body ground Always 10 kΩ or higher
G17-24 (CG8B) or V11-3 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (BACK DOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (BACK DOOR))
a.

Connect the G17 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-10 (E) - Body ground Always Below 1 Ω



c.

Using an oscilloscope, check the waveform.

B418156C03
2.5,0.365 2.927,0.594 0.427,0.229 4.385,0.375 4.813,0.604 0.427,0.229 2.854,4.458 3.01,4.458 3.01,4.458 3.302,3.76 true 1.719,2.01 1.875,2.01 1.875,2.01 2.167,1.313 true 5.625,0.646 5.427,0.646 5.427,0.646 4.948,1.281 true 5.76,2.115 5.5,2.115 5.5,2.115 4.969,1.417 true 0.323,0.188 0.635,0.344 0.313,0.156 10 false *a 2.563,2.875 2.875,3.031 0.313,0.156 10 false *b 2.646,4.365 2.958,4.521 0.313,0.156 10 false *c 2.583,0.385 2.927,0.573 0.344,0.188 10 false G16 4.479,0.385 4.823,0.573 0.344,0.188 10 false G17 2.313,3.615 2.76,3.771 0.448,0.156 10 false GND 1.573,1.906 1.917,2.094 0.344,0.188 10 false E 5.833,2.021 6.396,2.219 0.563,0.198 10 false CG8B 5.688,0.542 6.25,0.74 0.563,0.198 10 false CLG8
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Back door opener switch assembly is pressed - -


OK:
Tester Connection Condition Tool Setting Specified Condition
G17-8 (CLG8) - G16-10 (E) Procedure:
1.

Engine switch off

2.

All doors closed


- Not pulse generation
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Back door opener switch assembly off → on.


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)
G17-24 (CG8B) - G16-10 (E) Procedure:
1.

Engine switch off

2.

All doors closed


- Not pulse generation
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Back door opener switch assembly off → on.


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

4.REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (BACK DOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (BACK DOOR)
a.

Temporarily replace the No. 2 indoor electrical key antenna assembly (back door) with a new or known good one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Back Door)>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A8 is not output.



Result:
Proceed to
OK
NG



OK

END (NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (BACK DOOR) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)