Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System) › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041706 THEFT DETERRENT / KEYLESS ENTRY _0212880 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  B2784  Antenna Coil Open / Short  


DESCRIPTION

When an open or short circuit is detected in the transponder key amplifier coil built into the engine switch, the certification ECU (smart key ECU assembly) stores this DTC. This DTC is also stored as a past DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2784 Antenna Coil Open / Short The transponder key amplifier coil built into the engine switch is open (see below) or shorted (determined by communication with certification ECU (smart key ECU assembly)) (1 trip detection logic*1).
·

Terminal AGND, VC5, TXCT or CODE circuit is open (includes disconnection of the engine switch).

·

The transponder key amplifier coil built into the engine switch is open.


·

Engine switch

·

Harness or connector

·

Certification ECU (smart key ECU assembly)


DTC output confirmation operation:

With the shift lever in P*2 and the key held near the engine switch, an engine start operation is performed by pressing and holding the engine switch when the key battery is depleted.



*1: Only output while a malfunction is present.

*2: for Automatic Transmission


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started when key battery is depleted by holding key near engine switch and pressing and holding engine switch with shift lever in P* -

*: for Automatic Transmission


Related Data List and Active Test
DTC No. Data List and Active Test
B2784 -

WIRING DIAGRAM

E318139E01
5.281,0.667 5.74,0.865 0.458,0.198 10 false VC5 5.281,1.188 5.74,1.385 0.458,0.198 10 false TXCT 5.271,1.708 5.729,1.906 0.458,0.198 10 false CODE 5.281,2.219 5.74,2.417 0.458,0.198 10 false AGND 4.865,0.781 5.323,0.979 0.458,0.198 10 false G17 4.906,0.563 5.365,0.76 0.458,0.198 10 false 20 4.865,1.302 5.323,1.5 0.458,0.198 10 false G17 4.948,1.083 5.406,1.281 0.458,0.198 10 false 2 4.865,1.813 5.323,2.01 0.458,0.198 10 false G17 4.948,1.594 5.406,1.792 0.458,0.198 10 false 1 4.865,2.333 5.323,2.531 0.458,0.198 10 false G16 4.917,2.104 5.375,2.302 0.458,0.198 10 false 24 1.5,0.771 1.958,0.969 0.458,0.198 10 false VC5 1.438,1.281 1.896,1.479 0.458,0.198 10 false TXCT 1.365,1.708 1.823,1.906 0.458,0.198 10 false CODE 1.375,2.219 1.833,2.417 0.458,0.198 10 false AGND 1.927,0.667 2.385,0.865 0.458,0.198 10 false 10 1.938,1.188 2.396,1.385 0.458,0.198 10 false 7 1.938,1.708 2.396,1.906 0.458,0.198 10 false 8 1.938,2.219 2.396,2.417 0.458,0.198 10 false 6 0.583,3.021 1.042,3.219 0.458,0.198 10 false G45 0.594,3.167 2.073,3.365 1.479,0.198 10 false Engine Switch 5.094,3.042 6.896,3.406 1.802,0.365 10 false Certification ECU (Smart Key ECU Assembly) 6.167,0.302 6.625,0.5 0.458,0.198 10 false 5 V 6.167,1.531 6.625,1.729 0.458,0.198 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
a.

Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the G45 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-1 (CODE) - G45-8 (CODE) Always Below 1 Ω
G17-2 (TXCT) - G45-7 (TXCT) Always Below 1 Ω
G17-20 (VC5) - G45-10 (VC5) Always Below 1 Ω
G16-24 (AGND) - G45-6 (AGND) Always Below 1 Ω
G45-8 (CODE) - Body ground Always 10 kΩ or higher
G17-1 (CODE) - Body ground Always 10 kΩ or higher
G45-7 (TXCT) - Body ground Always 10 kΩ or higher
G17-2 (TXCT) - Body ground Always 10 kΩ or higher
G45-10 (VC5) - Body ground Always 10 kΩ or higher
G17-20 (VC5) - Body ground Always 10 kΩ or higher
G45-6 (AGND) - Body ground Always 10 kΩ or higher
G16-24 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE ENGINE SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE ENGINE SWITCH
a.

Temporarily replace the engine switch with a new or known good one.

Click hereEngine / Hybrid System>1GD-FTV STARTING>ENGINE SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
HINT:

Before checking for DTCs, perform "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.



Result:
Proceed to
OK
NG



OK

END (ENGINE SWITCH WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)