Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System) › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041706 THEFT DETERRENT / KEYLESS ENTRY _0212880 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  B278A  Short to GND in Immobiliser System Power Source Circuit  


DESCRIPTION

When there is a short to GND in the power supply for the transponder key amplifier of the engine switch, the certification ECU (smart key ECU assembly) stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B278A Short to GND in Immobiliser System Power Source Circuit A short to GND in the power supply of the transponder key amplifier of the engine switch (VC5 - VC5) (1 trip detection logic*1).
·

Engine switch

·

Harness or connector

·

Certification ECU (smart key ECU assembly)


DTC output confirmation operation:

With the shift lever in P*2 and the key held near the engine switch, an engine start operation is performed by pressing and holding the engine switch when the key battery is depleted.



*1: Only output while a malfunction is present.

*2: for Automatic Transmission


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started when key battery is depleted by holding key near engine switch and pressing and holding engine switch with shift lever in P* -

*: for Automatic Transmission


Related Data List and Active Test
DTC No. Data List and Active Test
B278A -

WIRING DIAGRAM

E318140E01
4.865,0.781 5.323,0.979 0.458,0.198 10 false G17 4.917,0.552 5.375,0.75 0.458,0.198 10 false 20 4.865,2.333 5.323,2.531 0.458,0.198 10 false G16 4.917,2.104 5.375,2.302 0.458,0.198 10 false 24 5.292,0.667 5.75,0.865 0.458,0.198 10 false VC5 5.292,2.219 5.75,2.417 0.458,0.198 10 false AGND 1.5,0.781 1.958,0.979 0.458,0.198 10 false VC5 1.375,2.219 1.833,2.417 0.458,0.198 10 false AGND 0.583,3.021 1.042,3.219 0.458,0.198 10 false G45 0.583,3.177 1.958,3.427 1.375,0.25 10 false Engine Switch 5.104,3.042 6.917,3.531 1.813,0.49 10 false Certification ECU (Smart Key ECU Assembly) 6.146,0.292 6.604,0.49 0.458,0.198 10 false 5 V 1.938,0.656 2.396,0.854 0.458,0.198 10 false 10 1.958,2.208 2.417,2.406 0.458,0.198 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B271009C14
1.26,0.156 1.729,0.479 0.469,0.323 1.833,1.656 2.406,2.042 true 1.208,1.656 0.635,2.052 true 1.365,0.25 1.802,0.5 0.438,0.25 10 false G45 0.125,0.125 0.385,0.375 0.26,0.25 10 false *a 2.969,3.292 3.385,3.563 0.417,0.271 10 false GND 0.323,2.021 0.719,2.25 0.396,0.229 10 false VC5 2.448,1.979 3.01,2.208 0.563,0.229 10 false AGND
*a Component with harness connector
(Engine Switch)


Using an oscilloscope, check the waveform.

HINT:

Perform this inspection on the engine switch side.


Measurement Condition
Item Content
Tester Connection G45-10 (VC5) - G45-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed

OK:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
a.

Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the G45 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-20 (VC5) - G45-10 (VC5) Always Below 1 Ω
G16-24 (AGND) - G45-6 (AGND) Always Below 1 Ω
G45-10 (VC5) - Body ground Always 10 kΩ or higher
G17-20 (VC5) - Body ground Always 10 kΩ or higher
G45-6 (AGND) - Body ground Always 10 kΩ or higher
G16-24 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the G16 and G17 certification ECU (smart key ECU assembly) connectors.


b.
E272490C07
1.51,0.135 1.969,0.406 0.458,0.271 0.948,1.958 1.417,1.406 true 2.531,1.969 2.094,1.406 true 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 1.604,0.198 1.917,0.396 0.313,0.198 10 false G45 2.958,3.281 3.333,3.458 0.375,0.177 10 false GND 2.573,1.896 3.125,2.073 0.552,0.177 10 false VC5 0.521,1.865 0.979,2.031 0.458,0.167 10 false AGND
*a Front view of wire harness connected
(to Engine Switch)


Using an oscilloscope, check the waveform.

HINT:

Perform this inspection on the engine switch side.


Measurement Condition
Item Content
Tester Connection G45-10 (VC5) - G45-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed

OK:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ASSEMBLY)