Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System)
RM3270E _58 Vehicle Interior _041706 THEFT DETERRENT / KEYLESS ENTRY _0212882 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  B2784  Antenna Coil Open / Short  


DESCRIPTION

When an open or short circuit is detected in the transponder key amplifier coil built into the transponder key ECU assembly, the transponder key ECU assembly stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2784 Antenna Coil Open / Short The antenna coil in the transponder key coil is open/shorted (1 trip detection logic*).
·

Harness or connector

·

Transponder key coil

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2784 Antenna Coil Status

WIRING DIAGRAM

E318145E04
4.052,0.969 4.667,1.167 0.615,0.198 10 false ANT1 4.063,1.885 4.677,2.083 0.615,0.198 10 false ANT2 3.802,0.969 4.417,1.167 0.615,0.198 10 false 4 3.729,1.885 4.344,2.083 0.615,0.198 10 false 15 1.49,0.969 2.104,1.167 0.615,0.198 10 false ANT1 1.469,1.885 2.083,2.083 0.615,0.198 10 false ANT2 0.667,2.479 1.281,2.677 0.615,0.198 10 false G137 0.667,2.615 2.469,2.833 1.802,0.219 10 false Transponder Key Coil 6.031,1.385 6.646,1.583 0.615,0.198 10 false IC 6.083,0.406 6.698,0.604 0.615,0.198 10 false 5 V 4.24,2.958 4.854,3.156 0.615,0.198 10 false G127 4.25,3.115 6.917,3.313 2.667,0.198 10 false Transponder Key ECU Assembly 2,0.979 2.615,1.177 0.615,0.198 10 false 1 2.01,1.906 2.625,2.104 0.615,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.



Result:
Result Proceed to
B2784 is not output A
B2784 is output B



A

B

3.CHECK CONNECTION OF CONNECTOR
3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the transponder key coil.


Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.



Result:
Result Proceed to
B2784 is not output A
B2784 is output B



A

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

B

6.CHECK TRANSPONDER KEY COIL (OUTPUT)
6.CHECK TRANSPONDER KEY COIL (OUTPUT)
a.

Using an oscilloscope, check the waveform.

B329326C26
3.323,0.073 3.813,0.281 0.49,0.208 4.115,1.167 3.813,0.792 true 3.177,1.167 3.323,0.771 true 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 1,1.448 1.313,1.646 0.313,0.198 10 false *b 1,3.542 1.313,3.74 0.313,0.198 10 false *c 6.542,2.479 7.083,2.781 0.542,0.302 10 false GND 6.552,4.552 7.094,4.854 0.542,0.302 10 false GND 3.979,1.188 4.521,1.49 0.542,0.302 10 false ANT1 3.031,1.188 3.573,1.49 0.542,0.302 10 false ANT2 3.417,0.094 3.875,0.292 0.458,0.198 10 false G137
*a Component with harness connected
(Transponder Key Coil)
*b Waveform 1
*c Waveform 2 - -


Waveform 1
Item Content
Tester Connection G137-1 (ANT1) - Body ground
Tool Setting 2 V/DIV., 2 s./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder

Waveform 2
Item Content
Tester Connection G137-5 (ANT2) - Body ground
Tool Setting 2 V/DIV., 2 s./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY COIL AND BODY GROUND)
7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY COIL AND BODY GROUND)
a.

Disconnect the G127 transponder key ECU assembly connector.


b.

Disconnect the G137 transponder key coil connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G127-4 (ANT1) - G137-1 (ANT1) Always Below 1 Ω
G127-15 (ANT2) - G137-5 (ANT2) Always Below 1 Ω
G127-4 (ANT1) - Body ground Always 10 kΩ or higher
G137-1 (ANT1) - Body ground Always 10 kΩ or higher
G127-15 (ANT2) - Body ground Always 10 kΩ or higher
G137-5 (ANT2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC
9.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.



Result:
Result Proceed to
B2784 is not output A
B2784 is output B



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B