Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH › 2015.08–2016.01
RM3270E _59 Vehicle Exterior _041719 WIPER / WASHER _0213518 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 84650 1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY

a.

Check the front wiper intermittent operation.

i.
E288057C14
0.167,1.083 0.667,1.333 0.5,0.25 2.698,1.073 3.198,1.323 0.5,0.25 1.031,1.479 0.823,1.833 true 2.177,1.167 2.375,0.625 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 0.292,1.125 0.75,1.323 0.458,0.198 10 false G20 2.313,0.438 2.604,0.604 0.292,0.167 10 false +1 0.688,1.896 0.979,2.063 0.292,0.167 10 false EW 2.823,1.115 3.281,1.313 0.458,0.198 10 false G21
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal G21-2 (+1) and a negative (-) lead to terminal G20-7 (EW).


ii.

Turn the ignition switch to ON.


iii.

Turn the wiper switch to the INT position.


iv.

Operate the intermittent wiper and check the voltage between terminals G21-2 (+1) and G20-7 (EW).

OK:

Voltage changes as shown in the illustration.


E136493E65
2.625,0.104 3.104,0.271 0.479,0.167 10 false FAST: 1.927,0.385 2.615,0.563 0.688,0.177 10 false 11 to 14 V 2.344,0.885 2.594,1.063 0.25,0.177 10 false 0 V 3.177,1.385 3.531,1.563 0.354,0.177 10 false Start 0.083,0.5 1.802,0.875 1.719,0.375 10 false Voltage between terminals G21-2 (+1) and G20-7 (EW): 0.771,1.375 1.854,1.552 1.083,0.177 10 false Wiper Operation: 3.354,1 4.542,1.198 1.188,0.198 10 false 1.6 +/- 1 second 5.792,1 7.021,1.198 1.229,0.198 10 false 10.7 +/- 5 seconds 2.729,1.385 3.083,1.563 0.354,0.177 10 false Stop 5.583,1.385 5.938,1.563 0.354,0.177 10 false Start 4.792,1.385 5.146,1.563 0.354,0.177 10 false Stop 4.438,0.104 4.979,0.302 0.542,0.198 10 false SLOW:

If the result is not as specified, replace the windshield wiper switch assembly.



b.

Check the front washer operation.

i.
E288057C15
0.167,1.083 0.667,1.333 0.5,0.25 2.698,1.073 3.198,1.323 0.5,0.25 1.031,1.479 0.844,1.833 true 1.5,1.479 1.729,1.854 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 0.292,1.125 0.75,1.323 0.458,0.198 10 false G20 1.656,1.896 1.948,2.063 0.292,0.167 10 false WF 0.729,1.875 1.021,2.042 0.292,0.167 10 false EW 2.823,1.115 3.281,1.313 0.458,0.198 10 false G21
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal G20-4 (WF) and a negative (-) lead to terminal G20-7 (EW).


ii.

Turn the ignition switch to ON.


iii.

Turn the washer switch on and off, and check the voltage between terminals G20-4 (WF) and G20-7 (EW).

OK:

Voltage changes as shown in the following illustration.


E226602E63
4.104,1.323 4.021,1.521 false 4.74,1.333 4.865,1.51 false 0.979,0.875 2.854,1.229 1.875,0.354 10 false Voltage between terminals 1.698,0.281 2.958,0.552 1.26,0.271 10 false Washer Switch: 2.604,1.531 4.354,1.771 1.75,0.24 10 false Approximately 0.5 seconds 4.708,1.531 6.708,1.729 2,0.198 10 false Approximately 2.2 seconds 2.948,0.823 3.708,1 0.76,0.177 10 false 11 to 14 V 3.365,1.167 3.74,1.313 0.375,0.146 10 false 0 V 3.292,0.479 3.688,0.635 0.396,0.156 10 false Off 3.354,0.188 3.729,0.365 0.375,0.177 10 false On 0.969,1.063 4.948,1.26 3.979,0.198 10 false G20-4 (WF) and G20-7 (EW):

If the result is not as specified, replace the windshield wiper switch assembly.



c.

Check the rear washer operation.

i.
E288057C21
0.167,1.083 0.667,1.333 0.5,0.25 2.698,1.073 3.198,1.323 0.5,0.25 1.031,1.479 0.844,1.833 true 1.823,1.5 1.823,1.844 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 0.292,1.125 0.75,1.323 0.458,0.198 10 false G20 1.74,1.896 2.031,2.063 0.292,0.167 10 false WR 0.729,1.875 1.021,2.042 0.292,0.167 10 false EW 2.823,1.115 3.281,1.313 0.458,0.198 10 false G21
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal G21-10 (WR) and a negative (-) lead to terminal G20-7 (EW).


ii.

Turn the ignition switch to ON.


iii.

Turn the rear washer switch on and off, and check the voltage between terminals G21-10 (WR) and G20-7 (EW).

OK:

Voltage changes as shown in the following illustration.


E226602E67
4.104,1.323 4.021,1.521 false 4.74,1.333 4.865,1.51 false 0.979,0.875 2.854,1.229 1.875,0.354 10 false Voltage between terminals 1.698,0.281 2.958,0.552 1.26,0.271 10 false Washer Switch: 2.604,1.531 4.354,1.771 1.75,0.24 10 false Approximately 0.5 seconds 4.708,1.531 6.708,1.729 2,0.198 10 false Approximately 2.2 seconds 2.948,0.823 3.708,1 0.76,0.177 10 false 11 to 14 V 3.365,1.167 3.74,1.313 0.375,0.146 10 false 0 V 3.292,0.479 3.688,0.635 0.396,0.156 10 false Off 3.354,0.188 3.729,0.365 0.375,0.177 10 false On 0.969,1.063 4.948,1.26 3.979,0.198 10 false G21-10 (WR) and G20-7 (EW):

If the result is not as specified, replace the windshield wiper switch assembly.