Home › Drivetrain › AXLE AND DIFFERENTIAL › DIFFERENTIAL OIL › 2015.08–2016.01
RM3270E _52 Drivetrain _041686 AXLE AND DIFFERENTIAL _0217061 DIFFERENTIAL OIL A

AXLE AND DIFFERENTIAL  DIFFERENTIAL OIL  REPLACEMENT  


PROCEDURE

Hide 1.DRAIN DIFFERENTIAL OIL

a.

for front differential:

i.

Stop the vehicle on a level surface.


ii.
A272242C04
1.646,0.906 2.094,0.813 true 0.24,4.094 0.344,3.615 0.344,3.615 0.521,3.615 true 0.24,4.333 0.5,4.448 0.5,4.448 0.667,4.448 true 0.979,3.958 1.198,4.167 1.198,4.167 1.344,4.167 true 1.49,3.719 1.875,3.813 true 0.719,4.354 1.031,4.51 0.313,0.156 10 false *1 0.573,3.531 0.885,3.688 0.313,0.156 10 false *2 1.938,3.76 2.25,3.917 0.313,0.156 10 false *3 1.396,4.073 1.854,4.271 0.458,0.198 10 false SST 2.146,0.708 2.604,0.906 0.458,0.198 10 false SST
*1 10 mm Straight Hexagon Wrench
*2 10 mm Union Nut Wrench
*3 Socket Adaptor


Using SST and a 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, remove the differential filler plug and gasket.

SST
09961-00950  


iii.

Remove the drain plug and gasket, and drain the oil.


iv.

Install a new gasket and the drain plug.

Torque:
64.7 N*m (660 kgf*cm, 48 ft.*lbf)



b.

for rear differential:

i.

Stop the vehicle on a level surface.


ii.

Remove the rear axle housing filler plug and gasket.


iii.

Remove the rear axle housing drain plug and gasket, and drain the oil.


iv.

Install a new gasket and the rear axle housing drain plug.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)



Hide 2.ADD DIFFERENTIAL OIL

a.
D025304C22
0.635,1.281 0.813,1.469 0.177,0.188 10 false *a
*a 0 to 5 mm


Add differential oil so that the oil level is within 0 to 5 mm (0 to 0.196 in.) from the bottom lip of the differential filler plug hole.

NOTICE:
·

After changing the oil, drive the vehicle, and then check the oil level again.

·

Too much or too little oil will lead to differential problems.



If necessary, fill the differential carrier with hypoid gear oil.

Recommended Viscosity:
Front Differential:

SAE 75W-85

Rear Differential:

SAE 75W-85


Differential Oil Type:
Front Differential:

Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent

Rear Differential:

Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent


Standard Front Differential Oil Capacity:

1.55 to 1.65 liters (1.64 to 1.74 US qts., 1.37 to 1.45 Imp. qts.)


Standard Rear Differential Oil Capacity:

3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.)



b.

Check for oil leakage when the oil level is low.


c.
A272243C03
1.156,0.813 1.615,0.813 true 0.958,4.021 1.177,4.281 1.177,4.281 1.323,4.281 true 1.469,3.813 1.927,3.833 true 0.552,3.76 0.365,3.76 0.365,3.76 0.24,4.177 true 0.51,4.427 0.271,4.427 true 0.573,4.354 0.885,4.51 0.313,0.156 10 false *1 0.625,3.698 0.938,3.854 0.313,0.156 10 false *2 1.99,3.75 2.302,3.906 0.313,0.156 10 false *3 0.802,0.75 1.26,0.948 0.458,0.198 10 false SST 1.385,4.198 1.844,4.396 0.458,0.198 10 false SST 2.229,1.927 2.688,2.125 0.458,0.198 10 false L3 2.458,1.021 2.885,1.229 0.427,0.208 10 false L1 2.021,0.958 2.448,1.167 0.427,0.208 10 false L2
*1 10 mm Straight Hexagon Wrench
*2 10 mm Union Nut Wrench
*3 Socket Adaptor


for front differential:

i.

Using SST and a 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, install a new gasket and the differential filler plug.

SST
09961-00950  

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)

NOTICE:
·

Make sure all the tools are connected in a straight line.

·

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.



Formula:

T' = T x L3 / (L1 + L2 + L3)

- T' = Spec. value of torque wrench

- T = Value of specified tightening torque

- L1 = Length of union nut wrench

- L2 = Length of SST

- L3 = Length of torque wrench




d.

for rear differential:

i.

Install a new gasket and the rear axle housing filler plug.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)