Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY › 2015.08–2016.01
RM3270E _52 Drivetrain _041686 AXLE AND DIFFERENTIAL _0217066 REAR DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 41433A 1.INSTALL DIFFERENTIAL LOCK CAM RING

a.
C325539C01
2.229,0.542 2.594,0.542 false 2.031,2.948 2.615,2.948 false 2.646,0.458 2.958,0.656 0.313,0.198 10 false *1 2.646,2.875 2.958,3.073 0.313,0.198 10 false *2
*1 Differential Lock Position Plate
*2 Differential Lock Cam Ring


Install the differential lock cam ring and differential lock position plate to the differential case RH.


Hide 41474A 2.INSTALL DIFFERENTIAL LOCK POSITION PLATE

a.
C325538

Using a T25 ''TORX'' socket wrench, install the 3 new screws.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


Hide 41302 3.ASSEMBLE REAR DIFFERENTIAL CASE SUB-ASSEMBLY

a.
C325778C01
2.208,1.458 3.115,1.458 3.115,1.458 3.115,1.667 true 3.063,1.698 3.375,1.896 0.313,0.198 10 false *1
*1 Differential Lock Spring


Install the differential lock spring to the differential case RH.


b.
C325779C01
0.646,1.927 0.646,1.625 false 1.469,1.917 1.469,1.625 false 0.594,1.958 0.906,2.156 0.313,0.198 10 false *1 1.406,1.948 1.719,2.146 0.313,0.198 10 false *2
*1 Rear No. 2 Differential Side Gear Thrust Washer
*2 Rear No. 3 Differential Side Gear Thrust Washer


Install the rear No. 2 differential side gear thrust washer and rear No. 3 differential side gear thrust washer to the differential side gear (dog clutch).


c.
C325780

Install the differential side gear (dog clutch) to the differential case RH.


d.
C327975C02
1.406,0.938 1.406,0.51 1.406,0.51 1.604,0.51 false 2.125,0.979 2.125,0.375 2.125,0.375 2.479,0.375 false 0.75,2.167 1.094,2.167 1.094,2.167 1.094,1.583 false 1.813,2.292 1.813,1.677 false 1.115,0.677 1.115,0.302 1.115,0.302 0.802,0.302 false 0.698,1.365 0.698,1.094 0.698,1.094 0.479,1.094 false 2.594,1.031 2.896,1.031 false 2.292,1.802 2.688,1.802 false 0.542,4.063 0.813,4.063 0.813,4.063 0.813,3.604 false 2.865,3.469 2.615,3.469 2.615,3.469 2.615,3.135 false 1.688,4.333 2.094,4.333 2.094,4.333 2.292,4.104 false 1.667,0.427 1.979,0.625 0.313,0.198 10 false *1 2.552,0.281 2.865,0.479 0.313,0.198 10 false *1 0.563,2.083 0.875,2.281 0.313,0.198 10 false *1 1.771,2.323 2.083,2.521 0.313,0.198 10 false *1 0.604,0.219 0.917,0.417 0.313,0.198 10 false *2 0.292,1.01 0.604,1.208 0.313,0.198 10 false *2 2.958,0.938 3.271,1.135 0.313,0.198 10 false *2 2.76,1.719 3.073,1.917 0.313,0.198 10 false *2 0.354,3.979 0.667,4.177 0.313,0.198 10 false *4 2.938,3.385 3.25,3.583 0.313,0.198 10 false *4 1.51,4.25 1.823,4.448 0.313,0.198 10 false *3
*1 Differential Pinion
*2 Rear Differential Pinion Thrust Washer
*3 Rear Differential Pinion Shaft
*4 Rear No. 2 Differential Pinion Shaft


Install the 4 differential pinions, 4 rear differential pinion thrust washers, rear differential pinion shaft and the 2 rear No. 2 differential pinion shafts in the differential case RH.


e.
C325544

Install the 2 rear differential pinion shaft pins.


f.
C325781

Install the rear No. 1 differential side gear thrust washer to the differential side gear.


g.
C325782

Install the differential side gear.


h.
C326405C01
0.417,0.646 0.417,0.385 0.417,0.385 0.833,0.385 false 0.281,2.625 0.281,2.094 0.281,2.094 0.583,2.094 false 0.365,0.688 0.677,0.885 0.313,0.198 10 false *1 0.229,2.688 0.542,2.885 0.313,0.198 10 false *2
*1 Differential Case LH
*2 Differential Case RH


Install the differential case LH to the differential case RH.


i.
C325541

Install the 2 screws.

Torque:
4.5 N*m (46 kgf*cm, 40 in.*lbf)


j.
C326878

Measure the side gear backlash.

i.

Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the differential case.

Standard backlash:

0.05 to 0.20 mm (0.00197 to 0.00787 in.)


If the backlash is not as specified, install 2 side gear thrust washers with different thicknesses.

HINT:

Using the table below, select 3 thrust washers which will ensure that the backlash is within the specifications.


Standard Washer Thickness:
Item Thrust Washer Thickness mm (in.)
Differential side gear No. 1 differential side gear thrust washer 1.05 to 1.15 (0.0414 to 0.0452)
1.15 to 1.25 (0.0453 to 0.0492)
1.25 to 1.35 (0.0493 to 0.0531)
1.35 to 1.45 (0.0532 to 0.0570)
Differential side gear (dog clutch) No. 2 differential side gear thrust washer 1.05 to 1.15 (0.0414 to 0.0452)
1.15 to 1.25 (0.0453 to 0.0492)
1.25 to 1.35 (0.0493 to 0.0531)
1.35 to 1.45 (0.0532 to 0.0570)
No. 3 differential side gear thrust washer 1.35 to 1.45 (0.0532 to 0.0570)




Hide 4.INSTALL DIFFERENTIAL RING GEAR

a.

Clean the contact surfaces of the rear differential case sub-assembly and differential ring gear.


b.

Heat the differential ring gear in boiling water that is approximately 100°C (212°F).


c.

Carefully remove the differential ring gear from the boiling water.


d.
C326879C01
1.708,1.292 2.563,1.292 false 2.625,1.198 2.938,1.396 0.313,0.198 10 false *a
*a Matchmark


After the moisture on the differential ring gear has completely evaporated, quickly align the matchmarks on the differential ring gear and electronic differential lock case and install the differential ring gear to the electronic differential lock case.


e.

After the ring gear cools down sufficiently, apply adhesive to the 12 bolts and Temporarily install them.

Thread lock:

Toyota Genuine Adhesive 1360K, Three Bond1360K or equivalent



f.

Diametrically tighten the 12 bolts uniformly in several passes.

Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)


Hide 5.INSTALL DIFFERENTIAL LOCK PLUNGER

a.
C325540

Install the differential lock plunger to the rear differential case sub-assembly.


Hide 41451H 6.INSTALL DIFFERENTIAL LOCK COIL

a.
C325537

Install the differential lock coil to the electronic differential lock case sub-assembly.


Hide 41367 7.INSTALL DIFFERENTIAL SOLENOID WASHER

a.
C327532C02
0.646,3.25 0.958,3.25 0.958,3.25 1.313,3.448 false 0.677,3.74 1.313,3.74 false 1.969,0.948 1.792,0.948 1.792,0.948 1.656,0.74 true 2.438,0.51 2.75,0.708 0.313,0.198 10 false *a 0.344,3.177 0.802,3.375 0.458,0.198 10 false SST 0.365,3.646 0.823,3.844 0.458,0.198 10 false SST 2.021,0.854 2.333,1.052 0.313,0.198 10 false *1
*1 Differential Solenoid Washer
*a 0 to 0.15 mm


Using SST and a press, press the differential solenoid washer to the electronic differential lock case sub-assembly.

SST
09316-20011  
09950-60010  (09951-00640)

Differential solenoid washer depth:

0 to 0.15 mm (0 to 0.00590 in.)


NOTICE:

Make sure that the end face of the differential solenoid washer does not protrude from the end face of the electronic differential lock case sub-assembly.



Hide 41301A 8.INSTALL REAR DIFFERENTIAL CASE BEARING

a.
C325900N01
0.854,0.938 1.469,0.938 false 0.552,0.875 1.01,1.073 0.458,0.198 10 false SST

for LH Side (Ring Gear Side):

i.

Using SST and a press, press a new rear differential case bearing (inner) to the electronic differential lock case sub-assembly.

SST
09950-60010  (09951-00600)



b.
C325901N01
0.792,0.906 1.521,0.906 false 0.698,2.719 0.927,2.719 0.927,2.719 1.563,2.896 true 0.49,0.844 0.948,1.042 0.458,0.198 10 false SST 0.396,2.656 0.854,2.854 0.458,0.198 10 false SST

for RH Side (Differential Lock Coil Side):

i.

Using SST and a press, press a new rear differential case bearing (inner) to the electronic differential lock case sub-assembly.

SST
09950-60010  (09951-00480, 09951-00570)



Hide 9.INSPECT DIFFERENTIAL RING GEAR RUNOUT

a.

Install the differential case on the carrier, and install the 2 plate washers so that there is no play in the bearing.


b.
C325524

Install the 2 differential bearing caps with the 4 bolts.

Torque:
113 N*m (1152 kgf*cm, 83 ft.*lbf)


c.
C325517C01
2.854,1.563 3.167,1.76 0.313,0.198 10 false *a
*a 98 mm (3.86 in.)


Using a dial indicator, measure the runout of the differential ring gear.

Maximum runout:

0.07 mm (0.00276 in.)



d.

Remove the 2 differential bearing caps, 2 plate washers and electronic differential lock case sub-assembly.


Hide 41115 10.INSTALL DIFFERENTIAL OIL STORAGE RING

a.
C326884C01
0.969,1.75 1.5,1.75 false 0.885,2.708 1.563,2.708 true 2.042,2.823 2.427,2.917 2.427,2.917 2.833,2.917 true 0.656,1.677 1.115,1.875 0.458,0.198 10 false SST 0.583,2.625 1.042,2.823 0.458,0.198 10 false SST 2.896,2.833 3.208,3.031 0.313,0.198 10 false *1
*1 Differential Oil Storage Ring


Using SST and a hammer, tap in the differential oil storage ring.

SST
09316-60011  (09316-00011, 09316-00071)

NOTICE:

Be careful not to damage the differential oil storage ring.



Hide 41201B 11.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C326897N01
0.979,0.49 1.563,0.49 false 0.948,0.865 1.625,0.865 true 0.667,0.406 1.125,0.604 0.458,0.198 10 false SST 0.646,0.781 1.104,0.979 0.458,0.198 10 false SST

Using SST and a press, press the rear drive pinion front tapered roller bearing (outer) into the differential carrier.

SST
09316-60011  (09316-00011, 09316-00031)


Hide 41201A 12.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C326898N01
0.865,0.635 1.427,0.635 false 0.906,1.406 1.375,1.406 true 0.552,0.552 1.01,0.75 0.458,0.198 10 false SST 0.583,1.323 1.042,1.521 0.458,0.198 10 false SST

Using SST and a press, press the adjust shim and rear drive pinion rear tapered roller bearing (outer) into the differential carrier.

SST
09316-60011  (09316-00011)
09951-01000  

HINT:

First, install an adjust shim that has the same thickness as the removed adjust shim. After checking the tooth contact pattern, replace the adjust shim with one of a different thickness if necessary.



Hide 41201A 13.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C326245N01
0.938,1.177 1.531,1.177 false 0.969,2.063 1.563,2.063 false 0.604,1.094 1.063,1.292 0.458,0.198 10 false SST 0.646,1.979 1.104,2.177 0.458,0.198 10 false SST

Using SST and a press, press the rear drive pinion rear tapered roller bearing (inner) onto the differential drive pinion.

SST
09309-37010  
09630-24014  (09620-24051)


Hide 14.ADJUST DIFFERENTIAL DRIVE PINION PRELOAD

a.
C326173N01
2.063,2.073 2.49,2.073 false 1.917,2.688 2.448,2.688 false 1.969,0.406 2.385,0.406 false 1.75,2.01 2.208,2.208 0.458,0.198 10 false SST 1.615,2.615 2.073,2.813 0.458,0.198 10 false SST 1.667,0.344 2,0.552 0.333,0.208 10 false SST

Install the differential drive pinion, rear drive pinion tapered roller bearing (inner).

SST
09316-60011  (09316-00011, 09316-00041)
09608-04031  

HINT:

Install the spacer and oil seal after adjusting the gear contact pattern.



b.
C325765

Install the rear differential drive pinion oil slinger.


c.
C326885C01
0.875,0.708 1.479,0.708 false 0.563,0.625 1.021,0.823 0.458,0.198 10 false SST 2.979,0.688 3.292,0.885 0.313,0.198 10 false *a 0.458,1.583 0.771,1.781 0.313,0.198 10 false *b
*a Turn
*b Hold


Using SST, install the rear drive pinion companion flange sub-assembly with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



d.

Adjust the drive pinion preload by tightening the rear drive pinion nut.


e.
C326886N01
1.792,0.479 2.083,0.208 2.083,0.208 2.396,0.208 false 2.469,0.125 2.927,0.323 0.458,0.198 10 false SST

Using SST to hold the rear drive pinion companion flange sub-assembly with dust deflector in place, slowly tighten the rear drive pinion nut within the drive pinion preload adjustment range so that it reaches the specified drive pinion preload (at Starting).

SST
09330-00021  (09330-00030)

Limit torque value:

457 N*m (4660 kgf*cm, 337 ft.*lbf) or less


NOTICE:
·

As there is no spacer, tighten a little at a time. Be careful not to overtighten the nut.

·

Apply hypoid gear oil LSD to the drive pinion thread and nut seat face.




f.

Using a torque wrench, measure the preload.

Standard Drive Pinion Preload (Starting Torque):
Bearing Preload
New bearing 1.51 to 3.48 N*m (16 to 35 kgf*cm, 14 to 30 in.*lbf)
Reused bearing 1.53 to 3.34 N*m (16 to 34 kgf*cm, 14 to 29 in.*lbf)


NOTICE:
·

For a more accurate measurement, rotate the bearing forward and backward several times before measuring.

·

Record the differential drive pinion preload for the total preload measurement.




Hide 41303E 15.INSTALL ELECTRONIC DIFFERENTIAL LOCK CASE SUB-ASSEMBLY

a.
C325526

Place the 2 rear differential case bearings (outer) to their respective bearings.

HINT:

Make sure the right and left races are not interchanged.



Hide 16.ADJUST DIFFERENTIAL RING GEAR BACKLASH

a.
C326170

Install the plate washer to the RH side (differential lock coil side).

NOTICE:

Make sure that the differential ring gear has backlash.



b.
C325518

Using a dial indicator, while holding the rear drive pinion companion flange sub-assembly with dust deflector, measure the ring gear backlash.

Standard backlash (reference):

0.10 to 0.20 mm (0.00394 to 0.00787 in.)



c.
C326170

Refer to the backlash when selecting a plate washer for the RH side (differential lock coil side).


d.
C326171

Select a plate washer for the LH side (ring gear side) so that there is no gap between the rear differential case bearing (outer) and differential case.


e.

Using a plastic-faced hammer, install the plate washer to the LH side (ring gear side).


f.
C325518

Using a dial indicator, adjust the ring gear backlash until it is within the specification.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


HINT:

If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the plate washers on both sides by an equal amount.


NOTICE:
·

There should be no clearance between the plate washer and case.

·

Make sure that there is ring gear backlash.




Hide 17.ADJUST SIDE BEARING PRELOAD

a.
C327531

After adjusting the backlash of the differential ring gear, remove the plate washer from the LH side (ring gear side).


b.
C124163

Using a micrometer, measure the thickness of the plate washer.


c.

Using the backlash as a reference, select a new plate washer that is 0.05 to 0.20 mm (0.00197 to 0.00787 in.) thicker than the removed plate washer and, using a plastic-faced hammer, tap it in so that it fits against the bearing.

HINT:

Select a plate washer which can be pressed in 2/3 of the full amount with your finger.



d.
C325518

Recheck the ring gear backlash.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.

HINT:

An approximately 0.02 mm (0.000787 in.) change in each plate washer results in a 0.03 mm (0.00118 in.) change in the backlash.


Standard Washer LH (Ring Gear Side):
Part No. Thickness mm (in.) Part No. Thickness mm (in.)
90564-59044 2.07 to 2.09 (0.0815 to 0.0822) 90564-59060 2.39 to 2.41 (0.0941 to 0.0948)
90564-59045 2.09 to 2.11 (0.0823 to 0.0830) 90564-59061 2.41 to 2.43 (0.0949 to 0.0956)
90564-59046 2.11 to 2.13 (0.0831 to 0.0838) 90564-59062 2.43 to 2.45 (0.0957 to 0.0964)
90564-59047 2.13 to 2.15 (0.0839 to 0.0846) 90564-59063 2.45 to 2.47 (0.0965 to 0.0972)
90564-59048 2.15 to 2.17 (0.0847 to 0.0854) 90564-59064 2.47 to 2.49 (0.0973 to 0.0980)
90564-59049 2.17 to 2.19 (0.0855 to 0.0862) 90564-59065 2.49 to 2.51 (0.0981 to 0.0988)
90564-59050 2.19 to 2.21 (0.0863 to 0.0870) 90564-59066 2.51 to 2.53 (0.0989 to 0.0996)
90564-59051 2.21 to 2.23 (0.0871 to 0.0877) 90564-59067 2.53 to 2.55 (0.0997 to 0.1003)
90564-59052 2.23 to 2.25 (0.0878 to 0.0885) 90564-59068 2.55 to 2.57 (0.1004 to 0.1011)
90564-59053 2.25 to 2.27 (0.0886 to 0.0893) 90564-59069 2.57 to 2.59 (0.1012 to 0.1019)
90564-59054 2.27 to 2.29 (0.0894 to 0.0901) 90564-59070 2.59 to 2.61 (0.1020 to 0.1027)
90564-59055 2.29 to 2.31 (0.0902 to 0.0909) 90564-59071 2.61 to 2.63 (0.1028 to 0.1035)
90564-59056 2.31 to 2.33 (0.0910 to 0.0917) 90564-59072 2.63 to 2.65 (0.1036 to 0.1043)
90564-59057 2.33 to 2.35 (0.0918 to 0.0925) 90564-59073 2.65 to 2.67 (0.1044 to 0.1051)
90564-59058 2.35 to 2.37 (0.0926 to 0.0933) 90564-59074 2.67 to 2.69 (0.1052 to 0.1059)
90564-59059 2.37 to 2.39 (0.0934 to 0.0940) - -


Standard Washer RH (Differential Lock Coil Side):
Part No. Thickness mm (in.) Part No. Thickness mm (in.)
90564-59075 2.05 to 2.07 (0.0807 to 0.0814) 90564-59091 2.37 to 2.39 (0.0934 to 0.0940)
90564-59076 2.07 to 2.09 (0.0815 to 0.0822) 90564-59092 2.39 to 2.41 (0.0941 to 0.0948)
90564-59077 2.09 to 2.11 (0.0823 to 0.0830) 90564-59093 2.41 to 2.43 (0.0949 to 0.0956)
90564-59078 2.11 to 2.13 (0.0831 to 0.0838) 90564-59094 2.43 to 2.45 (0.0957 to 0.0964)
90564-59079 2.13 to 2.15 (0.0839 to 0.0846) 90564-59095 2.45 to 2.47 (0.0965 to 0.0972)
90564-59080 2.15 to 2.17 (0.0847 to 0.0854) 90564-59096 2.47 to 2.49 (0.0973 to 0.0980)
90564-59081 2.17 to 2.19 (0.0855 to 0.0862) 90564-59097 2.49 to 2.51 (0.0981 to 0.0988)
90564-59082 2.19 to 2.21 (0.0863 to 0.0870) 90564-59098 2.51 to 2.53 (0.0989 to 0.0996)
90564-59083 2.21 to 2.23 (0.0871 to 0.0877) 90564-59099 2.53 to 2.55 (0.0997 to 0.1003)
90564-59084 2.23 to 2.25 (0.0878 to 0.0885) 90564-59100 2.55 to 2.57 (0.1004 to 0.1011)
90564-59085 2.25 to 2.27 (0.0886 to 0.0893) 90564-59101 2.57 to 2.59 (0.1012 to 0.1019)
90564-59086 2.27 to 2.29 (0.0894 to 0.0901) 90564-59102 2.59 to 2.61 (0.1020 to 0.1027)
90564-59087 2.29 to 2.31 (0.0902 to 0.0909) 90564-59103 2.61 to 2.63 (0.1028 to 0.1035)
90564-59088 2.31 to 2.33 (0.0910 to 0.0917) 90564-59104 2.63 to 2.65 (0.1036 to 0.1043)
90564-59089 2.33 to 2.35 (0.0918 to 0.0925) 90564-59105 2.65 to 2.67 (0.1044 to 0.1051)
90564-59090 2.35 to 2.37 (0.0926 to 0.0933) 90564-59106 2.67 to 2.69 (0.1052 to 0.1059)



Hide 18.INSPECT TOTAL PRELOAD

a.
C326896

Using a torque wrench, measure the preload with the teeth of the differential drive pinion and differential ring gear in contact.

Standard Total Preload:
Reduction Ratio Item Specified Condition
3.583 New bearing 1.80 to 4.10 N*m (19 to 41 kgf*cm, 16 to 36 in.*lbf)
Reused bearing 1.82 to 3.92 N*m (19 to 39 kgf*cm, 17 to 34 in.*lbf)
3.909 New bearing 1.77 to 4.05 N*m (19 to 41 kgf*cm, 16 to 35 in.*lbf)
Reused bearing 1.80 to 3.87 N*m (19 to 39 kgf*cm, 16 to 34 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 19.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

C326169

a.

Coat 3 or 4 teeth at 3 different positions on the differential ring gear with Prussian blue.


b.

Hold the companion flange firmly in place and rotate the differential ring gear in both directions.


c.

Inspect the tooth contact pattern.

C222533C02
1.49,1.177 1.906,1.427 0.417,0.25 10 false *a 2.479,0.313 2.865,0.521 0.385,0.208 12 false *A 3.115,0.708 3.51,0.948 0.396,0.24 10 false *b 5.146,0.708 5.521,0.948 0.375,0.24 10 false *c 4.417,1.531 4.99,1.917 0.573,0.385 10 false *d 3.167,2.531 3.677,2.865 0.51,0.333 10 false *e 5.198,2.552 5.573,2.865 0.375,0.313 10 false *f 4.479,3.354 4.896,3.771 0.417,0.417 10 false *g 2.469,4.51 3.052,4.833 0.583,0.323 12 false *B 3.208,5.104 3.615,5.406 0.406,0.302 10 false *h 5.198,5.115 5.5,5.365 0.302,0.25 10 false *i 3.198,7.042 3.604,7.406 0.406,0.365 10 false *j 5.167,7.052 5.656,7.427 0.49,0.375 10 false *k 4.49,5.969 4.958,6.333 0.469,0.365 10 false *d 4.469,7.906 4.906,8.396 0.438,0.49 10 false *g
*A Drive Side *B Coast Side
*a Proper Contact *b Toe Contact
*c Face Contact *d Select an adjusting washer that will shift the drive pinion closer to the ring gear.
*e Heel Contact *f Flank Contact
*g Select an adjusting washer that will shift the drive pinion away from the ring gear. *h Heel Contact
*i Flank Contact *j Toe Contact
*k Face Contact - -


C217047C04
2.01,1.625 1.469,1.625 1.469,1.625 1.469,1.354 false 1.042,1.896 0.75,1.896 0.75,1.896 0.75,1.51 false 1.104,1.813 1.417,2.01 0.313,0.198 10 false *1 2.052,1.563 2.365,1.76 0.313,0.198 10 false *2
*1 Adjust Shim
*2 Rear Drive Pinion Rear Tapered Roller Bearing (Outer)


If the teeth are not contacting properly, use the following chart to select a adjust shim.


Standard Adjust Shim Thickness:
Part No. Thickness mm (in.) Part No. Thickness mm (in.)
90564-78001 1.71 to 1.73 (0.0674 to 0.0681) 90564-78013 1.95 to 1.97 (0.0768 to 0.0775)
90564-78002 1.73 to 1.75 (0.0682 to 0.0688) 90564-78014 1.97 to 1.99 (0.0776 to 0.0783)
90564-78003 1.75 to 1.77 (0.0689 to 0.0696) 90564-78015 1.99 to 2.01 (0.0784 to 0.0791)
90564-78004 1.77 to 1.79 (0.0697 to 0.0704) 90564-78016 2.01 to 2.03 (0.0792 to 0.0799)
90564-78005 1.79 to 1.81 (0.0705 to 0.0712) 90564-78017 2.03 to 2.05 (0.0780 to 0.0807)
90564-78006 1.81 to 1.83 (0.0713 to 0.0720) 90564-78018 2.05 to 2.07 (0.0808 to 0.0814)
90564-78007 1.83 to 1.85 (0.0721 to 0.0728) 90564-78019 2.07 to 2.09 (0.0815 to 0.0822)
90564-78008 1.85 to 1.87 (0.0729 to 0.0736) 90564-78020 2.09 to 2.11 (0.0823 to 0.0830)
90564-78009 1.87 to 1.89 (0.0737 to 0.0744) 90564-78021 2.11 to 2.13 (0.0831 to 0.0838)
90564-78010 1.89 to 1.91 (0.0745 to 0.0751) 90564-78022 2.13 to 2.15 (0.0839 to 0.0846)
90564-78011 1.91 to 1.93 (0.0752 to 0.0759) 90564-78023 2.15 to 2.17 (0.0847 to 0.0854)
90564-78012 1.93 to 1.95 (0.0760 to 0.0767) 90564-78024 2.17 to 2.19 (0.0855 to 0.0862)



Hide 41204 21.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 41214 22.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41303E 24.REMOVE ELECTRONIC DIFFERENTIAL LOCK CASE SUB-ASSEMBLY

Hide 41201B 26.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

Hide 41231 27.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

Hide 41201B 28.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

Hide 41115 29.REMOVE DIFFERENTIAL OIL STORAGE RING

Hide 41201A 30.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

Hide 41201A 31.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C326898C01
0.865,0.635 1.427,0.635 false 0.906,1.406 1.375,1.406 true 1.854,1.531 2.427,1.531 true 0.552,0.552 1.01,0.75 0.458,0.198 10 false SST 0.583,1.323 1.042,1.521 0.458,0.198 10 false SST 2.49,1.448 2.802,1.646 0.313,0.198 10 false *1
*1 Rear Drive Pinion Rear Tapered Roller Bearing (Outer)


Using SST and a press, press the adjust shim and rear drive pinion rear tapered roller bearing (outer) into the differential carrier.

SST
09316-60011  (09316-00011)
09951-01000  


Hide 41115 32.INSTALL DIFFERENTIAL OIL STORAGE RING

a.
C326884C01
0.969,1.75 1.5,1.75 false 0.885,2.708 1.563,2.708 true 2.042,2.823 2.427,2.917 2.427,2.917 2.833,2.917 true 0.656,1.677 1.115,1.875 0.458,0.198 10 false SST 0.583,2.625 1.042,2.823 0.458,0.198 10 false SST 2.896,2.833 3.208,3.031 0.313,0.198 10 false *1
*1 Differential Oil Storage Ring


Using SST and a hammer, tap in a new differential oil storage ring.

SST
09316-60011  (09316-00011)

NOTICE:

Be careful not to damage the differential oil storage ring.



Hide 41201B 33.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C326897C01
0.979,0.49 1.563,0.49 false 0.948,0.865 1.625,0.865 true 1.927,1.021 2.448,1.021 true 0.667,0.406 1.125,0.604 0.458,0.198 10 false SST 0.646,0.781 1.104,0.979 0.458,0.198 10 false SST 2.521,0.927 2.833,1.125 0.313,0.198 10 false *1
*1 Rear Drive Pinion Front Tapered Roller Bearing (Outer)


Using SST and a press, press the rear drive pinion front tapered roller bearing (outer) into the differential carrier.

SST
09316-60011  (09316-00011, 09316-00031)


Hide 41231 34.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C325767

Install a new rear differential drive pinion bearing spacer.


Hide 41201B 35.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C326404

Install the rear drive pinion front tapered roller bearing (inner) to the drive pinion.


Hide 36.INSTALL DIFFERENTIAL DRIVE PINION

a.
C326173N01
2.063,2.073 2.49,2.073 false 1.917,2.688 2.448,2.688 false 1.969,0.406 2.385,0.406 false 1.75,2.01 2.208,2.208 0.458,0.198 10 false SST 1.615,2.615 2.073,2.813 0.458,0.198 10 false SST 1.667,0.344 2,0.552 0.333,0.208 10 false SST

Using SST and a press, install the differential drive pinion.

SST
09316-60011  (09316-00011, 09316-00041)
09608-04031  


Hide 84222 37.INSTALL NO. 1 TRANSFER INDICATOR SWITCH (REAR DIFFERENTIAL LOCK POSITION SWITCH)

a.
C337670

Install a new No. 1 transfer indicator switch (rear differential lock position switch) with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 41303E 38.INSTALL ELECTRONIC DIFFERENTIAL LOCK CASE SUB-ASSEMBLY

a.
C325526

Place the 2 new bearing outer races to their respective bearings.


Hide 39.INSTALL WIRING HARNESS CONNECTOR

a.
C337669

Install a new wiring harness connector with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


b.
C326172

Connect the connector.


Hide 40.INSTALL DIFFERENTIAL BEARING CAP

a.

Install the 2 plate washers.


b.
C325524C01
0.406,1.208 1.583,1.208 true 0.563,1.208 0.563,0.854 0.563,0.854 1.167,0.854 true 0.24,1.115 0.552,1.313 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks on the differential bearing cap and differential carrier.


c.

Install the right and left differential bearing caps with the 4 bolts.

Torque:
113 N*m (1152 kgf*cm, 83 ft.*lbf)


Hide 41214 41.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C325765

Install the rear differential drive pinion oil slinger to the differential drive pinion.


Hide 41201C 42.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

Hide 41204 43.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

a.
C326885C01
0.875,0.708 1.479,0.708 false 0.563,0.625 1.021,0.823 0.458,0.198 10 false SST 2.979,0.688 3.292,0.885 0.313,0.198 10 false *a 0.458,1.583 0.771,1.781 0.313,0.198 10 false *b
*a Turn
*b Hold


Using SST, install the rear drive pinion companion flange sub-assembly with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



b.

Apply hypoid gear oil LSD to the drive pinion thread and nut seat face.


c.
C326916C01
0.427,0.677 0.604,0.677 0.604,0.677 0.76,0.865 false 3.115,1.167 3.427,1.365 0.313,0.198 10 false *a 0.208,1.385 0.521,1.583 0.313,0.198 10 false *b 0.115,0.615 0.573,0.813 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST to hold the companion flange in place, install a new nut.

SST
09330-00021  (09330-00030)

Limit torque value:

457 N*m (4660 kgf*cm, 337 ft.*lbf) or less



Hide 44.INSPECT TOTAL PRELOAD

a.

Using a torque wrench, measure the preload with the teeth of the differential drive pinion and differential ring gear in contact.


b.
C326896

Using a torque wrench, measure the total preload.

Standard Total Preload:
Reduction Ratio Bearing Preload
3.583 New bearing 1.90 to 4.2 N*m (20 to 42 kgf*cm, 17 to 37 in.*lbf)
Reused bearing 1.92 to 4.02 N*m (20 to 40 kgf*cm, 17 to 35 in.*lbf)
3.909 New bearing 1.87 to 4.15 N*m (20 to 42 kgf*cm, 17 to 36 in.*lbf)
Reused bearing 1.90 to 3.97 N*m (20 to 40 kgf*cm, 17 to 35 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 45.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C325518

Using a dial indicator, check the backlash of the differential ring gear.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


If the backlash is not as specified, adjust the side bearing preload or perform repairs as necessary.

HINT:

Perform the measurement at 3 or more positions around the circumference of the differential ring gear.



Hide 41204 46.INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C325516C01
2.573,1.906 2.885,2.104 0.313,0.198 10 false *a
*a 30 mm (1.18 in.)


Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Maximum Runout:
Runout Maximum
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)



Hide 47.STAKE DRIVE PINION NUT

a.
C327037

Using a chisel and hammer, stake the drive pinion nut.