Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT PROPELLER SHAFT ASSEMBLY(except TSAM Made)
RM3270E _52 Drivetrain _041685 DRIVE SHAFT / PROPELLER SHAFT _0217830 FRONT PROPELLER SHAFT ASSEMBLY(except TSAM Made) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT PROPELLER SHAFT ASSEMBLY(except TSAM Made)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 1.REMOVE SPIDER BEARING

HINT:

Use the same procedure for both spiders.


a.
C162215C01
1.531,0.917 0.906,0.49 0.906,0.49 1.813,0.656 true 0.698,0.375 1.01,0.573 0.313,0.198 10 false *a
*a Matchmark


Place matchmarks on the flange yoke and propeller shaft.


b.
C307728

Using a brass bar and hammer, slightly tap in the spider bearing outer races.


c.

Using 2 screwdrivers, remove the 4 snap rings from the grooves.


d.
C307744C01
1.167,1 1.167,0.417 1.167,0.417 1.25,0.417 true 2.5,1.333 2.865,1.323 true 1.323,1.573 1.635,1.771 0.313,0.198 10 false *a 0.979,0.125 1.292,0.323 0.313,0.198 10 false *b 1.292,0.333 1.75,0.531 0.458,0.198 10 false SST 2.948,1.25 3.167,1.469 0.219,0.219 10 false A
*a Turn
*b Hold


Using SST, push out the spider bearing from the front propeller shaft assembly.

SST
09332-25010  

HINT:

Before installing SST, sufficiently raise the part labeled A. If the part labeled A is too low, it may be difficult to install SST.



e.
C307729C01
2.719,1.146 2.313,0.719 true 2.771,1.104 3.083,1.302 0.313,0.198 10 false *a
*a Hammering Point


Tap off the spider bearing with a hammer.

NOTICE:

Do not tap the shaft.


HINT:

Remove the spider bearing on the opposite side using the same procedure.



f.

Remove the flange yoke from the front propeller shaft assembly.


g.
C307746C01
2.125,1.146 2.5,1.146 true 0.573,1.188 0.948,1.188 true 1.656,0.604 1.969,0.802 0.313,0.198 10 false *a 0.438,0.177 0.781,0.385 0.344,0.208 10 false *b 1.948,1.083 2.156,1.313 0.208,0.229 10 false A 0.26,1.115 0.656,1.313 0.396,0.198 10 false SST
*a Turn
*b Hold


Install the 2 removed spider bearing outer races to the spider.


h.

Using SST, push out the spider bearing from the flange yoke.

SST
09332-25010  

HINT:

Before installing SST, sufficiently raise the part labeled A. If the part labeled A is too low, it may be difficult to install SST.



i.
C258224C01
1.396,0.313 1.823,0.313 1.823,0.313 2.417,0.604 true 1.188,0.219 1.406,0.417 0.219,0.198 10 *a
*a Hammering Point


Tap off the spider bearing with a hammer.


j.

Remove the spider.