Home › Engine / Hybrid System › 5L-E ENGINE MECHANICAL › CYLINDER HEAD › from 2016.01
RM3270E _51 Engine / Hybrid System _048650 5L-E ENGINE MECHANICAL _0231147 CYLINDER HEAD A

5L-E ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Gradually heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).


b.
A057248N01
1.594,1.052 1.073,0.531 1.073,0.531 1.615,1.354 true 0.729,0.417 1.156,0.688 0.427,0.271 10 false SST

Using SST and a hammer, tap out the intake valve guide bush.

SST
09201-10000  (09201-01080)
09950-70010  (09951-07100)


c.

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head sub-assembly.


d.

Select a new intake valve guide bush.

New Guide Bush:
Item Specified Condition
Bush bore diameter 13.004 to 13.025 mm (0.512 to 0.513 in.) 13.054 to 13.075 mm (0.514 to 0.515 in.)
Bush to be used STD O/S 0.05


If the valve guide bush bore diameter of the cylinder head sub-assembly is more than 13.025 mm (0.513 in.), machine the valve guide bush bore diameter to between 13.054 and 13.075 mm (0.514 and 0.515 in.).

If the valve guide bush bore diameter of the cylinder head sub-assembly is more than 13.075 mm (0.515 in.), replace the cylinder head sub-assembly.


e.

Gradually heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).


f.
A070793N01
0.948,0.74 0.479,0.604 0.479,0.604 0.948,1.333 true 0.135,0.521 0.438,0.677 0.302,0.156 10 false SST 3.25,0.573 3.406,0.729 0.156,0.156 10 false H

Using SST and a hammer, tap in a new intake valve guide bush to the specified protrusion height.

SST
09950-70010  (09951-07100)
09201-10000  (09201-01070)

Standard protrusion height (H):

10.8 to 11.2 mm (0.425 to 0.441 in.)



g.
A056822C02
0.833,0.302 1,0.302 1,0.302 1.646,0.688 false 0.656,0.198 0.896,0.396 0.24,0.198 10 false *a
*a Sharp 8.0 mm Reamer


Using a sharp 8.0 mm reamer, ream the intake valve guide bush to obtain the standard clearance between the intake valve guide bush and valve stem.

Standard clearance:

0.02 to 0.055 mm (0.000787 to 0.00217 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Gradually heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).


b.
A057249N01
1.531,0.813 1.135,0.417 1.135,0.417 1.563,1.365 true 0.781,0.302 1.229,0.594 0.448,0.292 10 false SST

Using SST and a hammer, tap out the exhaust valve guide bush.

SST
09201-10000  (09201-01080)
09950-70010  (09951-07100)


c.

Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head sub-assembly.


d.

Select a new exhaust valve guide bush.

New Guide Bush:
Item Specified Condition
Bush bore diameter 13.004 to 13.025 mm (0.512 to 0.513 in.) 13.054 to 13.075 mm (0.514 to 0.515 in.)
Bush to be used STD O/S 0.05


If the valve guide bush bore diameter of the cylinder head sub-assembly is more than 13.025 mm (0.513 in.), machine the valve guide bush bore diameter to between 13.054 and 13.075 mm (0.514 and 0.515 in.).

If the valve guide bush bore diameter of the cylinder head sub-assembly is more than 13.075 mm (0.515 in.), replace the cylinder head sub-assembly.


e.

Gradually heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).


f.
A070794N01
0.833,0.823 0.469,0.635 0.469,0.635 0.854,1.406 true 0.156,0.531 0.583,0.792 0.427,0.26 10 false SST 3.156,0.521 3.417,0.719 0.26,0.198 10 false H

Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

SST
09950-70010  (09951-07100)
09201-10000  (09201-01070)

Standard protrusion height (H):

10.8 mm to 11.2 mm (0.425 to 0.441 in.)



g.
A056823C01
1.646,0.656 1.188,0.26 1.188,0.26 1.073,0.26 false 0.854,0.167 1.021,0.354 0.167,0.188 10 false *1
*a Sharp 8.0 mm Reamer


Using a sharp 8.0 mm reamer, ream the exhaust valve guide bush to obtain the standard clearance between the exhaust valve guide bush and valve stem.

Standard clearance:

0.035 to 0.07 mm (0.00138 to 0.00276 in.)



Hide 3.REPLACE TIGHT PLUG

HINT:

It is not necessary to remove a tight plug unless it is being replaced.


a.

Remove the tight plugs.


b.

Apply adhesive to new tight plugs.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.


NOTICE:

Do not start the engine for 1 hour after installation.



c.

Using SST and a hammer, tap in the tight plugs as shown in the illustration.

Position A

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)

Position B

SST
09950-60010  (09951-00300)
09950-70010  (09951-07100)

Position C

SST
09950-60010  (09951-00450)
09950-70010  (09951-07100)

A378633C01
0.677,0.333 0.99,0.49 0.313,0.156 10 false *a 3.229,0.083 3.542,0.24 0.313,0.156 10 false *b 0.698,1.656 1.01,1.813 0.313,0.156 10 false *c 3.229,1.729 3.542,1.885 0.313,0.156 10 false *d 5.427,3.708 5.74,3.865 0.313,0.156 10 false *e 5.708,0.979 6.021,1.135 0.313,0.156 10 false A 5.052,0.979 5.365,1.135 0.313,0.156 10 false A 4.406,0.979 4.719,1.135 0.313,0.156 10 false A 3.76,0.979 4.073,1.135 0.313,0.156 10 false A 4.313,2.854 4.625,3.01 0.313,0.156 10 false A 4.958,2.854 5.271,3.01 0.313,0.156 10 false A 5.604,2.854 5.917,3.01 0.313,0.156 10 false A 1.333,0.813 1.646,0.969 0.313,0.156 10 false C 1.542,2.542 1.854,2.698 0.313,0.156 10 false C 1.646,2.188 1.958,2.344 0.313,0.156 10 false B
*a Front Side *b Cylinder Head Cover Sub-assembly Side
*c Rear Side *d Intake Manifold Side
*e Stops - -



Hide 4.REPLACE RING PIN

HINT:

It is not necessary to remove a ring pin unless it is being replaced.


a.

Remove the ring pin from the cylinder head sub-assembly.


b.

Using a plastic-faced hammer, tap in a new ring pin to the cylinder head sub-assembly until the pin stops.

Standard protrusion:

Less than 5 mm (0.197 in.)


A378634C01
0.583,0.302 0.896,0.458 0.313,0.156 10 false *a 3.729,0.021 4.042,0.177 0.313,0.156 10 false *b 2.104,1.792 2.417,1.948 0.313,0.156 10 false *c 2.583,1.417 2.896,1.573 0.313,0.156 10 false *d 3.792,2.219 4.104,2.375 0.313,0.156 10 false *e
*a Front Side *b Cylinder Head Cover Sub-assembly Side
*c 8 mm (0.315 in.) *d 11 mm (0.433 in.)
*e Less than 5 mm (0.197 in.) - -