Home › Engine / Hybrid System › 5L-E ENGINE MECHANICAL › CYLINDER HEAD › from 2016.01
RM3270E _51 Engine / Hybrid System _048650 5L-E ENGINE MECHANICAL _0231147 CYLINDER HEAD A

5L-E ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Thoroughly clean all parts to be assembled.

·

Before installing the parts, apply fresh engine oil to all sliding and rotating surfaces.

·

Replace all gaskets and oil seals with new ones.



PROCEDURE

Hide 1.INSTALL STUD BOLT

HINT:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Install the stud bolts to the cylinder head sub-assembly.

Torque:
for stud bolt A : 6.0 N*m (61 kgf*cm, 53 in.*lbf)
for stud bolt B : 12 N*m (122 kgf*cm, 9 ft.*lbf)
for stud bolt C : 26 N*m (265 kgf*cm, 19 ft.*lbf)

A378635C01
0.427,0.146 0.74,0.302 0.313,0.156 10 false *a 0.469,1.417 0.781,1.573 0.313,0.156 10 false *b 3.958,0.135 4.271,0.292 0.313,0.156 10 false *c 6.583,1 6.896,1.156 0.313,0.156 10 false A 2.979,0.792 3.292,0.948 0.313,0.156 10 false B 2.094,2.25 2.406,2.406 0.313,0.156 10 false C 1.469,3.354 1.74,3.615 0.271,0.26 10 false *d 1.458,4.135 1.771,4.292 0.313,0.156 10 false *e 2.281,3.667 2.594,3.823 0.313,0.156 10 false *f 3.677,3.479 3.896,3.76 0.219,0.281 10 false *g 3.677,4.156 3.99,4.313 0.313,0.156 10 false *h 4.479,3.802 4.792,3.958 0.313,0.156 10 false *I 5.896,3.74 6.208,3.896 0.313,0.156 10 false *j 6.677,3.948 6.99,4.104 0.313,0.156 10 false *k 1.052,0.792 1.365,0.948 0.313,0.156 10 false B 1.448,2.26 1.76,2.417 0.313,0.156 10 false C 5.917,4.177 6.229,4.333 0.313,0.156 10 false *j 5.615,4.438 5.927,4.594 0.313,0.156 10 false A 3.406,4.438 3.719,4.594 0.313,0.156 10 false B 1.219,4.438 1.531,4.594 0.313,0.156 10 false C 5.625,4.615 5.927,4.781 0.302,0.167 10 false M6 3.406,4.615 3.708,4.781 0.302,0.167 10 false M8 1.177,4.615 1.563,4.792 0.385,0.177 10 false M10
*a Intake Manifold Side *b Exhaust Manifold Side
*c Cylinder Head Cover Sub-assembly Side *d 23.5 mm (0.925 in.)
*e 12 mm (0.472 in.) *f 44.5 mm (1.75 in.)
*g 14 mm (0.551 in.) *h 11 mm (0.433 in.)
*i 36 mm (1.42 in.) *j 9 mm (0.354 in.)
*k 25 mm (0.984 in.) - -



Hide 11183 2.INSTALL SEMICIRCULAR PLUG

a.

Remove any old packing (FIPG material).


b.
A056910C02
2.583,0.594 2.448,0.167 2.448,0.167 2.271,0.167 true 2.094,0.063 2.375,0.313 0.281,0.25 10 false *a
*a Seal Packing


Apply seal packing to the semicircular plug as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

The semicircular plug must be installed within 3 minutes from the completion of applying the seal packing.

·

Prevent seal packing from being stuck to the camshaft thrust groove.




c.

Install the semicircular plug to the cylinder head sub-assembly.


Hide 11106 3.INSTALL COMBUSTION CHAMBER SUB-ASSEMBLY

a.
A378636C01
1.292,1.115 1.542,0.656 1.542,0.656 1.688,0.656 true 0.375,0.615 0.771,0.615 true 0.448,0.167 0.615,0.167 0.615,0.167 0.896,0.604 true 1.396,0.135 1.25,0.135 1.25,0.135 1,0.594 true 1.594,0.302 1.448,0.302 1.448,0.302 1.115,0.615 true 0.167,1.573 0.479,1.729 0.313,0.156 10 false *a 0.198,0.531 0.51,0.688 0.313,0.156 10 false *b 0.281,0.083 0.594,0.24 0.313,0.156 10 false *c 1.458,0.052 1.771,0.208 0.313,0.156 10 false *d 1.635,0.229 1.948,0.385 0.313,0.156 10 false *e 1.75,0.573 2.063,0.729 0.313,0.156 10 false *f
*a Front
*b No. 1 Combustion Chamber
*c No. 2 Combustion Chamber
*d No. 3 Combustion Chamber
*e No. 4 Combustion Chamber
*f Mark 1, 2 or 3


Select the number of shim, according to the table below.

Select a New Combustion Chamber:
Item Specified Condition
Mark 1 5.91 to 5.94 mm (0.2327 to 0.2338 in.)
Mark 2 5.94 to 5.97 mm (0.234 to 0.235 in.)
Mark 3 5.97 to 6.0 mm (0.235 to 0.236 in.)



b.
A057261C02
0.635,0.792 0.417,1.323 0.417,1.323 0.281,1.323 true 0.104,1.229 0.354,1.438 0.25,0.208 10 false *a
*a Chamber Knock Pin


Align the combustion chamber knock pin with the cylinder head sub-assembly notch.


c.

Using a plastic-faced hammer, tap in the combustion chamber sub-assembly.


d.
A057260

Using a dial indicator, check the combustion chamber protrusion.

Combustion chamber protrusion:

-0.03 to 0.03 mm (-0.00118 to 0.00118 in.)


If the protrusion is less than the specification, adjust with shims.

If the protrusion is more than the specification, replace the combustion chamber sub-assembly and recheck the protrusion.


Hide 13711E 4.INSTALL INTAKE VALVE STEM OIL SEAL

a.
A059919E02
1.375,0.177 2.406,0.844 true 1.052,0.094 1.396,0.25 0.344,0.156 10 false SST

Using SST, push in a new intake valve stem oil seal to the intake valve guide bush.

SST
09201-41020  


Hide 13715A 5.INSTALL EXHAUST VALVE STEM OIL SEAL

a.
A379225N01
2.26,1.177 2.708,1.635 2.708,1.635 2.917,1.635 true 2.969,1.521 3.427,1.719 0.458,0.198 10 true SST

Using SST, push in a new exhaust valve stem oil seal to the exhaust valve guide bush.

SST
09201-41020  


Hide 13711 6.INSTALL INTAKE VALVE

a.
A255584C10
2.408,0.397 2.586,0.563 0.178,0.167 10 *a
*a 30 mm (1.18 in.) or more


Apply a sufficient coat of engine oil to the tip area of the intake valve shown in the illustration.


b.
A056915E03
1.979,0.344 2.563,0.146 false 2.604,0.031 3.083,0.271 0.479,0.24 10 false SST

Install the intake valve, valve spring seat, inner compression spring and valve spring retainer to the cylinder head sub-assembly.


c.

Using SST, compress the inner compression spring and install the 2 valve spring retainer locks to the valve stem.

SST
09202-70020  (09202-00030)


d.
A122913C02
1.823,1.927 1.677,1.927 1.677,1.927 1,1.229 true 1.885,1.823 2.167,2.01 0.281,0.188 10 false *a
*a 5 mm Pin Punch


Using a 5 mm pin punch and plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the valve stem tip.



Hide 13715 7.INSTALL EXHAUST VALVE

a.
A255584C10
2.408,0.397 2.586,0.563 0.178,0.167 10 *a
*a 30 mm (1.18 in.) or more


Apply a sufficient coat of engine oil to the tip area of the exhaust valve shown in the illustration.


b.
A056916E03
1.719,0.438 2.49,0.125 false 2.531,0.021 3.021,0.313 0.49,0.292 10 true SST

Install the exhaust valve, valve spring seat, inner compression spring and valve spring retainer.


c.

Using SST, compress the inner compression spring and install the 2 valve spring retainer locks to the valve stem to the cylinder head sub-assembly.

SST
09202-70020  (09202-00030)


d.
A122914C02
0.302,1.854 0.448,1.854 0.448,1.854 0.917,1.219 true 0.125,1.771 0.385,2.01 0.26,0.24 10 false *a
*a 5 mm Pin Punch


Using a 5 mm pin punch and plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the valve stem tip.



Hide 13751 8.INSTALL VALVE LIFTER

a.

Install the valve lifter and shim.


b.

Check that the valve lifter rotates smoothly by hand.