Home › Engine / Hybrid System › 5L-E ENGINE MECHANICAL › CYLINDER BLOCK › from 2016.01
RM3270E _51 Engine / Hybrid System _048650 5L-E ENGINE MECHANICAL _0231150 CYLINDER BLOCK G

5L-E ENGINE MECHANICAL  CYLINDER BLOCK  INSPECTION  


PROCEDURE

Hide 11448 1.INSPECT CYLINDER BLOCK OIL ORIFICE

a.

Check the cylinder block oil orifice for damage or clogging.

If necessary, replace the cylinder block oil orifice.


Hide 15605 2.INSPECT OIL CHECK VALVE SUB-ASSEMBLY

a.
A118168C01
1.813,0.958 1.979,0.313 1.979,0.313 2.167,0.313 true 2.219,0.208 2.531,0.365 0.313,0.156 10 false *a
*a Ball
V100135

Push


Push the ball of the oil check valve sub-assembly with a wooden stick to check if it is stuck.

If the ball of the oil check valve sub-assembly is stuck, replace the oil check valve sub-assembly.


Hide 15708 3.INSPECT NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.

Check the No. 1 oil nozzle sub-assembly for damage or clogging.

If necessary, replace the No. 1 oil nozzle sub-assembly.


Hide 11401 4.CLEAN CYLINDER BLOCK SUB-ASSEMBLY

a.

Using a gasket scraper, remove all the gasket material from the top surface of the cylinder block sub-assembly.


b.

Using a soft brush and solvent, thoroughly clean the cylinder block sub-assembly.


Hide 11401 5.INSPECT CYLINDER BLOCK SUB-ASSEMBLY

a.
A056744

Using a precision straightedge and feeler gauge, measure the surface of the cylinder block sub-assembly that contacts the cylinder head sub-assembly for warpage.

Maximum warpage:

0.2 mm (0.00787 in.)


If the warpage is more than the maximum, replace the cylinder block sub-assembly.


b.

Visually check the cylinders for vertical scratches.

If deep scratches are present, rebore all 4 cylinders. If necessary, replace the cylinder block sub-assembly.


Hide 6.INSPECT CYLINDER BORE

a.
A378641C01
0.49,0.615 0.625,0.615 0.625,0.615 1.188,1.375 true 1.135,0.448 1.271,0.448 1.271,0.448 1.833,1.208 true 1.75,0.281 1.885,0.281 1.885,0.281 2.448,1.042 true 2.302,0.146 2.438,0.146 2.438,0.146 3,0.906 true 3.01,2.333 3.01,0.927 true 0.813,2.771 0.948,2.771 0.948,2.771 1.51,3.094 true 0.917,2.531 1.052,2.531 1.052,2.531 1.604,3.063 true 2.083,2.49 1.958,2.49 1.958,2.49 1.729,3.01 true 2.24,2.688 2.115,2.688 2.115,2.688 1.875,3 true 2.552,3.302 2.406,3.302 2.406,3.302 1.865,3.031 true 0.302,0.521 0.615,0.677 0.313,0.156 10 false *a 0.948,0.354 1.26,0.51 0.313,0.156 10 false *b 1.563,0.188 1.875,0.344 0.313,0.156 10 false *c 2.125,0.052 2.438,0.208 0.313,0.156 10 false *d 2.948,2.354 3.26,2.51 0.313,0.156 10 false *e 0.625,2.688 0.938,2.844 0.313,0.156 10 false *a 0.729,2.438 1.042,2.594 0.313,0.156 10 false *b 2.135,2.396 2.448,2.552 0.313,0.156 10 false *c 2.292,2.594 2.604,2.75 0.313,0.156 10 false *d 2.594,3.208 2.906,3.365 0.313,0.156 10 false *e
*a No. 1
*b No. 2
*c No. 3
*d No. 4
*e Mark 1, 2 or 3


Inspect the cylinder bore diameter.

HINT:

There are 3 sizes of the standard cylinder bore diameter, marked "1", "2" and "3" accordingly. The mark is stamped on the lower left rear of the cylinder block.


i.
A303249C08
1.198,2.427 1.323,2.427 1.323,2.427 1.604,2.844 true 2.198,2.396 2.063,2.396 2.063,2.396 1.719,2.698 true 1.01,2.323 1.208,2.5 0.198,0.177 10 false *a 2.229,2.292 2.448,2.469 0.219,0.177 10 false *b 0.969,3.813 1.188,3.99 0.219,0.177 10 false *c 1.688,3.5 2,3.698 0.313,0.198 10 false A 2.417,3.469 2.635,3.635 0.219,0.167 10 false *d 1.708,4.146 2.021,4.344 0.313,0.198 10 false C 1.698,3.813 2.01,4.01 0.313,0.198 10 false B 2.417,4.167 2.635,4.333 0.219,0.167 10 false *d
*a Axial Direction
*b Thrust Direction
*c Center
*d 10 mm (0.394 in.)
V100135

Front


Using a cylinder gauge, measure the cylinder bore diameter at positions A, B and C in the thrust and axial directions.

Standard Diameter:
Item Specified Condition
Mark 1 99.50 to 99.51 mm (3.9173 to 3.9177 in.)
Mark 2 99.51 to 99.52 mm (3.9177 to 3.9181 in.)
Mark 3 99.52 to 99.53 mm (3.9181 to 3.9185 in.)


Maximum Diameter:
Item Specified Condition
STD 99.73 mm (3.93 in.)
O/S 0.50 100.23 mm (3.95 in.)


If the diameter is more than the maximum, rebore all 4 cylinders. If necessary, replace the cylinder block sub-assembly.



b.
A056740C02
0.417,1.688 0.563,1.688 0.563,1.688 0.875,1.354 true 0.24,1.583 0.552,1.813 0.313,0.229 10 false *a
*a Ridge Reamer


Inspect the cylinder ridge.

If the wear is less than 0.2 mm (0.00787 in.), using a ridge reamer, grind the top of the cylinder.


Hide 13101 7.CLEAN PISTON

a.

Using a gasket scraper, remove the carbon from the piston top.


b.

Using a groove cleaning tool or broken ring, clean the piston ring grooves.


c.

Using solvent and a brush, thoroughly clean the piston.

NOTICE:

Do not use a wire brush.



Hide 13101 8.INSPECT PISTON WITH PIN SUB-ASSEMBLY

HINT:

When replacing the piston sub-assembly (w/ pin) with a supply part, there are a number of piston diameter sizes to choose from, but there is only one size of piston pin diameter.


a.
A057046C03
2.344,0.615 2.469,0.219 2.469,0.219 2.583,0.219 true 1.917,0.458 1.729,0.135 1.729,0.135 1.531,0.135 true 2.708,1.406 2.958,1.615 0.25,0.208 10 false *c 2.604,0.125 2.854,0.344 0.25,0.219 10 false *b 1.365,0.052 1.521,0.208 0.156,0.156 10 false *a
*a Front Mark
*b Size Mark
*c Distance


Using a micrometer, measure the piston diameter at right angles to the piston center line where the distance from the piston head is as specified.

Distance:

61.27 to 61.33 mm (2.41 to 2.42 in.)


Standard Piston Diameter:
Item Specified Condition
Mark 1 99.45 to 99.46 mm (3.9153 to 3.9157 in.)
Mark 2 99.46 to 99.47 mm (3.9157 to 3.9161 in.)
Mark 3 99.47 to 99.48 mm (3.9161 to 3.9165 in.)
O/S 0.50 99.95 to 99.98 mm (3.935 to 3.936 in.)



b.
A054725

Using a micrometer, measure the piston pin diameter.

Standard Piston Pin Diameter:
Item Specified Condition
Mark A 29.000 to 29.004 mm (1.1417 to 1.1419 in.)
Mark B 29.004 to 29.008 mm (1.1419 to 1.1420 in.)
Mark C 29.008 to 29.012 mm (1.1420 to 1.1422 in.)



c.
A056600

Inspect the piston pin fit.

i.

At 60°C (140°F), check that the piston pin can be pushed into the piston pin hole with your thumb.

If the pin can be installed at a lower temperature, replace the piston with pin sub-assembly.



Hide 9.INSPECT PISTON OIL CLEARANCE

a.

Measure the cylinder bore diameter in the thrust direction.


b.

Subtract the piston diameter measurement from the cylinder bore diameter measurement.

Standard oil clearance:

0.04 to 0.06 mm (0.00157 to 0.00236 in.)


Maximum oil clearance:

0.13 mm (0.00512 in.)


If the oil clearance is more than the maximum, replace all the piston with pin sub-assemblies. If necessary, replace the cylinder block sub-assembly.


Hide 10.INSPECT RING GROOVE CLEARANCE

a.

Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.

Standard Groove Clearance:
Item Specified Condition
No. 1 piston ring 0.057 to 0.101 mm (0.00224 to 0.00398 in.)
No. 2 piston ring 0.06 to 0.10 mm (0.00236 to 0.00394 in.)
Oil ring 0.03 to 0.07 mm (0.00118 to 0.00276 in.)


Maximum groove clearance:

0.2 mm (0.00787 in.)


If the clearance is more than the maximum, replace the piston.


Hide 11.INSPECT PISTON RING END GAP

a.

Insert the piston ring into the cylinder bore.


b.

Using a piston, push the piston ring a little beyond the bottom of the ring travel, 140 mm (5.15 in.) from the top of the cylinder block.


c.

Using a feeler gauge, measure the end gap.

Standard End Gap:
Item Specified Condition
No. 1 piston ring 0.35 to 0.47 mm (0.0138 to 0.0185 in.)
No. 2 piston ring 0.47 to 0.60 mm (0.0185 to 0.0236 in.)
Oil ring 0.2 to 0.4 mm (0.00787 to 0.0157 in.)


Maximum End Gap:
Item Specified Condition
No. 1 piston ring 1.29 mm (0.0508 in.)
No. 2 piston ring 1.42 mm (0.0559 in.)
Oil ring 1.22 mm (0.0480 in.)


If the end gap is more than the maximum, replace the piston ring.

If the end gap is more than the maximum even with a new piston ring, rebore all 4 cylinders or replace the cylinder block sub-assembly.


Hide 12.INSPECT PISTON PIN OIL CLEARANCE

a.
A149774C07
1.625,2.25 1.135,2.427 1.135,2.427 1.042,2.427 true 2.042,1.865 2.708,1.313 2.708,1.313 2.802,1.313 true 2.833,1.219 3.021,1.385 0.188,0.167 10 false *a 0.833,2.333 1.042,2.521 0.208,0.188 10 false *b
*a Front Mark
*b Connecting Rod Bush Inside Diameter Mark A, B or C


Using a caliper gauge, measure the inside diameter of the connecting rod bush.

Standard Bush Inside Diameter:
Item Specified Condition
Mark A 29.008 to 29.012 mm (1.1420 to 1.1422 in.)
Mark B 29.012 to 29.016 mm (1.1422 to 1.1424 in.)
Mark C 29.016 to 29.020 mm (1.1424 to 1.1425 in.)



b.

Subtract the piston pin diameter measurement from the connecting rod bush inside diameter measurement.

Standard oil clearance:

0.004 to 0.012 mm (0.000157 to 0.000472 in.)


Maximum oil clearance:

0.05 mm (0.00197 in.)


If the oil clearance is more than the maximum, replace the connecting rod sub-assembly.

If necessary, replace the piston with pin sub-assembly.


Hide 13201 13.INSPECT CONNECTING ROD SUB-ASSEMBLY

a.

Using a rod aligner and feeler gauge, check the connecting rod alignment.

i.
A057235

Check if the connecting rod sub-assembly is bent.

Maximum bend:

0.05 mm (0.00196 in.) per 100 mm (3.94 in.)


If the bend is more than the maximum, replace the connecting rod sub-assembly.


ii.
A057236

Check if the connecting rod sub-assembly is twisted.

Maximum twist:

0.15 mm (0.00591 in.) per 100 mm (3.94 in.)


If the twist is more than the maximum, replace the connecting rod sub-assembly.



Hide 13265 14.INSPECT CONNECTING ROD BOLT

a.
A057237C02
0.552,0.25 0.719,0.458 0.167,0.208 10 false *a
*a Compressed Bolt


Using a vernier caliper, measure the diameter of the tension portion of the connecting rod bolt.

Standard diameter:

8.4 to 8.6 mm (0.331 to 0.339 in.)


Minimum diameter:

8.2 mm (0.323 in.)


If the diameter is less than the minimum, replace the connecting rod bolt.


Hide 13411 15.INSPECT CRANKSHAFT

a.

Inspect for circle runout.

i.

Place the crankshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.06 mm (0.00236 in.)


If the circle runout is more than the maximum, replace the crankshaft.



b.
A057239

Inspect the main journals and crank pins.

i.

Using a micrometer, measure the diameter of each main journal and crank pin.

Standard main journal diameter:

61.985 to 62.000 mm (2.4403 to 2.4409 in.)


Standard crank pin diameter:

54.988 to 55.000 mm (2.1649 to 2.1654 in.)


If the diameter is not as specified, check the connecting rod oil clearance (Click hereEngine / Hybrid System>5L-E ENGINE MECHANICAL>CYLINDER BLOCK>DISASSEMBLY) and crankshaft oil clearance (Click hereEngine / Hybrid System>5L-E ENGINE MECHANICAL>CYLINDER BLOCK>DISASSEMBLY). If necessary, grind or replace the crankshaft.


ii.

Check each main journal and crank pin for taper and out of round as shown in the illustration.

Maximum taper and out of round:

0.02 mm (0.000787 in.)


If the taper and out of round is more than the maximum, replace the crankshaft.



c.

If necessary, grind and hone the main journals and/or crank pins.

i.

Grind and hone the main journals and/or crank pins to the finished undersized diameter.


ii.

Install new main journal and/or crankshaft pin undersized bearing.