Home › Engine / Hybrid System › 5L-E ENGINE MECHANICAL › CYLINDER BLOCK › from 2016.01
RM3270E _51 Engine / Hybrid System _048650 5L-E ENGINE MECHANICAL _0231150 CYLINDER BLOCK A

5L-E ENGINE MECHANICAL  CYLINDER BLOCK  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE TIGHT PLUG

HINT:

If coolant leaks from a tight plug or a plug is corroded, replace it.


a.

Remove the tight plugs.


b.

Apply adhesive to new tight plugs.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Do not start the engine for 1 hour after installation.



c.

Using SST and a hammer, tap in the tight plugs as shown in the illustration.

Position A

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)

Position B

SST
09950-60010  (09951-00350)
09950-70010  (09951-07100)

Position C

SST
09950-60010  (09951-00500)
09950-70010  (09951-07100)

A118124C02
4.156,0.219 4.354,0.427 0.198,0.208 10 false *b 6.313,3.479 6.521,3.698 0.208,0.219 10 false *d 0.604,0.198 0.792,0.417 0.188,0.219 10 false *a 0.646,2.5 0.813,2.708 0.167,0.208 10 false *c 1.74,1.354 1.896,1.563 0.156,0.208 10 true A 0.948,3.854 1.094,4.083 0.146,0.229 10 true B 5.115,1.542 5.281,1.823 0.167,0.281 10 true C 1.521,3.854 1.667,4.083 0.146,0.229 10 true B 2.115,3.854 2.26,4.083 0.146,0.229 10 true B 2.667,3.854 2.813,4.083 0.146,0.229 10 true B 2.323,1.365 2.458,1.573 0.135,0.208 10 true A
*a RH Side *b Rear Side
*c LH Side *d Stops



Hide 2.REPLACE STRAIGHT PIN

HINT:

It is not necessary to remove a straight pin unless it is being replaced.


a.

Remove the straight pins.


b.

Using a plastic-faced hammer, tap in new straight pins to the cylinder block sub-assembly.

Standard protrusion height:

14.5 mm (0.571 in.) or less


A378642C01
0.865,0.083 1.177,0.24 0.313,0.156 10 false *a 3.823,0.875 4.135,1.031 0.313,0.156 10 false *b 4.281,0.25 4.594,0.406 0.313,0.156 10 false *c 5.865,0.948 6.177,1.104 0.313,0.156 10 false *d
*a Rear Side *b 22 mm (0.866 in.)
*c 10 mm (0.394 in.) *d Protrusion Height



Hide 3.REPLACE RING PIN

HINT:

It is not necessary to remove the ring pin unless it is being replaced.


a.

Remove the ring pins.


b.

Using a plastic-faced hammer, tap in new ring pins to the cylinder block sub-assembly.

Standard protrusion height:

4.5 mm (0.177 in.) or less


A378643C02
0.844,0.042 1.156,0.198 0.313,0.156 10 false *a 0.479,1.906 0.792,2.063 0.313,0.156 10 false *b 4.052,0.063 4.365,0.219 0.313,0.156 10 false *c 2.938,2.729 3.25,2.885 0.313,0.156 10 false *d 3.49,3.063 3.802,3.219 0.313,0.156 10 false *e 4.323,2.708 4.635,2.865 0.313,0.156 10 false *f 4.74,3.042 5.073,3.292 0.333,0.25 10 false *g 6.135,3.104 6.448,3.26 0.313,0.156 10 false *h 4.146,1.76 4.302,1.958 0.156,0.198 10 true B 6.438,1.771 6.594,1.969 0.156,0.198 10 true B 3.5,2.448 3.656,2.646 0.156,0.198 10 true B 4.781,2.427 4.938,2.625 0.156,0.198 10 true A 1.052,3.625 1.26,3.802 0.208,0.177 10 true A 1.896,3.625 2.104,3.802 0.208,0.177 10 true A 2.063,1.854 2.271,2.031 0.208,0.177 10 true A 1.073,1.865 1.281,2.042 0.208,0.177 10 true A
*a Front Side *b Rear Side
*c Cylinder Head Sub-assembly Side *d 7 mm (0.276 in.)
*e 14.5 mm (0.571 in.) *f 8 mm (0.315 in.)
*g 11 mm (0.433 in.) *h Protrusion Height



Hide 11432A 4.REPLACE NO. 1 TAPER SCREW PLUG

HINT:

If a No. 1 taper screw plug is deformed or its threads are damaged, replace it.


a.
A225169

Remove the No. 1 taper screw plug.


b.

Clean the cylinder block sub-assembly side hole and new No. 1 taper screw plug with non-residue solvent.


c.

Apply adhesive to 2 or 3 threads of the No. 1 taper screw plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the No. 1 taper screw plug.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 13201A 5.REPLACE CONNECTING ROD SMALL END BUSH

a.
A057244E03
1.271,1.656 1.51,1.656 false 2.344,1.656 1.885,1.656 false 2.406,0.594 1.969,0.594 false 1.229,0.594 1.594,0.594 false 1.635,0.5 2.031,0.771 0.396,0.271 10 false SST 1.552,1.573 1.948,1.844 0.396,0.271 10 false SST

Using SST and a press, press out the connecting rod small end bush.

SST
09222-54011  (09222-03016, 09222-03026, 09222-03021)


b.
A056739

Using a round file, lightly file off any roughness from the small end of the connecting rod sub-assembly.


c.
A057240C02
1.969,0.615 2.354,0.615 true 1.969,1.24 2.365,1.24 true 2.052,1.708 2.365,1.708 false 2.385,0.521 2.635,0.74 0.25,0.219 10 false *a 2.385,1.146 2.646,1.344 0.26,0.198 10 false *b 2.417,1.625 2.802,1.875 0.385,0.25 10 false SST
*a Oil Hole
*b Ball


Attach a new connecting rod small end bush to SST with the ball of SST inside the oil hole of the connecting rod small end bush.

SST
09222-54011  (09222-03021)


d.
A056722C02
2,0.5 2.604,0.99 2.604,0.99 2.083,1.688 true 2.646,0.875 2.948,1.094 0.302,0.219 10 false *a
*a Oil Hole


Align the oil holes of the connecting rod small end bush and connecting rod sub-assembly.


e.
A057245C01
0.875,0.781 0.667,0.781 false 1.125,0.24 1.5,0.24 false 2.375,0.594 1.917,0.25 false 1.135,1.021 1.5,0.833 false 2.49,1.135 1.917,0.823 true 1.177,1.865 1.5,1.688 false 2.323,1.698 1.938,1.698 false 1.563,0.146 1.927,0.396 0.365,0.25 10 false SST 1.563,1.573 1.927,1.823 0.365,0.25 10 false SST 1.563,0.74 1.927,0.99 0.365,0.25 10 false SST 0.438,0.708 0.604,0.896 0.167,0.188 10 false *1
*1 Connecting Rod Small End Bush


Using SST and a press, press in the connecting rod small end bush.

SST
09222-54011  (09222-03016, 09222-03026, 09222-03021)


f.
A057241

Using a pin hole grinder, hone the connecting rod small end bush to obtain the specified clearance between the connecting rod small end bush and piston pin.

Standard oil clearance:

0.004 to 0.012 mm (0.0002 to 0.0005 in.)



g.
A057242

Check that the piston pin fits at normal room temperature.


h.

Coat the piston pin with engine oil, and push it into the connecting rod with your thumb.