Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP(for 5L-E) › from 2016.01
RM3270E _55 Steering _041696 POWER ASSIST SYSTEMS _0233645 VANE PUMP(for 5L-E) G

POWER ASSIST SYSTEMS  VANE PUMP(for 5L-E)  INSPECTION  


PROCEDURE

Hide 1.INSPECT CLEARANCE BETWEEN VANE PUMP SHAFT AND BUSHING IN FRONT HOUSING

C106282N01
3.063,0.99 3.219,1.188 0.156,0.198 10 false a 1,1.073 1.156,1.271 0.156,0.198 10 false b

a.

Using a micrometer, measure the diameter (a) of the vane pump shaft.


b.

Using a caliper gauge, measure the inside diameter (b) of the front housing.

NOTICE:

Do not damage the bushing in the front housing.



c.

Subtract (a) from (b) to calculate the oil clearance.

Maximum clearance:

0.07 mm (0.00276 in.) or less


If the clearance is more it is more than the maximum, replace the vane pump assembly.


Hide 2.INSPECT VANE PUMP ROTOR AND VANE PUMP PLATE

a.
C101978

Using a feeler gauge, measure the clearance between the side face of the vane pump rotor groove and the vane pump plates.

Maximum clearance:

0.03 mm (0.0012 in.)


HINT:

Refer to the following table to select an appropriate combination of vane pump rotor, vane pump cam ring and vane pump plates.


Combination of Vane Pump Rotor, Vane Pump Cam Ring and Vane Pump Plates:
Vane Pump Cam Ring Part No. Vane Pump Rotor Part No. Vane Pump Plate Part No.
44325-06110 44313-02160 44345-06060
44325-06120 44313-02170 44345-06070
44325-06130 44313-02180 44345-06080
44325-06140 44313-02190 44345-06090
44325-06150 44313-06200 44345-06100


If the clearance is more than the maximum, replace the vane pump plates, vane pump rotor and vane pump cam ring.


Hide 3.INSPECT FLOW CONTROL VALVE

a.
C324322C01
2.198,0.229 2.51,0.385 0.313,0.156 10 false *a
*a Compressed Air


C220817C07
0.75,0.802 0.75,0.333 0.75,0.333 2.052,0.333 true 1.563,1.375 1.563,0.333 true 2.146,0.26 2.677,0.719 0.531,0.458 10 false *a
*a Mark


Check the flow control valve for leakage. Close one of the holes and apply compressed air at 392 to 490 kPa (4.00 to 4.99 kgf/cm2, 56.9 to 71.0 psi) to the hole on the opposite side. Confirm that the air does not flow out of the end hole.

NOTICE:

Make sure to use clean and dry air.


If there is leakage, replace the flow control valve.

HINT:
·

Check the mark on the front housing and replace the flow control valve with one having the same mark as that of the front housing.

·

Refer to the following table to select an appropriate combination of front housing and flow control valve.



Combination of Front Housing and Flow Control Valve:
Front Housing Mark Flow Control Valve Part No. Flow Control Valve Mark
A 44330-0K130 A
B 44330-0K140 B
C 44330-0K150 C
D 44330-0K160 D
E 44330-0K170 E
F 44330-0K180 F



b.

Coat the flow control valve with power steering fluid.

NOTICE:

Make sure to use new power steering fluid.



c.

Insert the flow control valve into the flow control valve installation hole of the front housing, and check that the flow control valve enters smoothly under its own weight.

If the flow control valve does not enter the front housing smoothly, replace the flow control valve.


Hide 4.INSPECT FLOW CONTROL VALVE COMPRESSION SPRING

a.
C322716N01
1.635,0.26 1.792,0.458 0.156,0.198 10 false A

Using a vernier caliper, measure the free length of the flow control valve compression spring.

Minimum free length (A) (Reference):

33.24 mm (1.31 in.)


If the length is less than the minimum, replace the flow control valve compression spring.


Hide 5.INSPECT PRESSURE PORT UNION

a.

If the union seat in the pressure port union is severely damaged, replace the pressure port union.