Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP(for 5L-E) › from 2016.01
RM3270E _55 Steering _041696 POWER ASSIST SYSTEMS _0233645 VANE PUMP(for 5L-E) A

POWER ASSIST SYSTEMS  VANE PUMP(for 5L-E)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 44302A 1.INSTALL VANE PUMP HOUSING OIL SEAL

a.

Coat the lip of a new vane pump housing oil seal with power steering fluid.


b.
C106283N01
1.521,0.719 0.979,0.521 0.979,0.521 1.594,0.563 false 0.667,0.427 1.125,0.625 0.458,0.198 10 false SST

Using SST and a press, press in the vane pump housing oil seal to the front vane pump housing.

SST
09950-60010  (09951-00280)
09950-70010  (09951-07100)

NOTICE:

Make sure that the vane pump housing oil seal is installed in the correct direction as shown in the illustration.



Hide 44312 2.INSTALL VANE PUMP SHAFT

a.
C106284C01
1.5,1.25 0.896,0.563 0.896,0.563 1.875,1.094 true 0.656,0.448 0.969,0.604 0.313,0.156 10 false *a
*a Power Steering Fluid


Coat the inside surface of the bushing in the front vane pump housing with power steering fluid.


b.

Gradually insert the vane pump shaft from the pulley side.


Hide 3.INSTALL VANE PUMP ROTOR

a.
C106285

Install the vane pump rotor.

HINT:

The vane pump rotor has no specific direction.



b.

Using a snap ring expander, install a new vane pump shaft snap ring to the vane pump shaft.


c.

Coat all 10 vane pump plate with power steering fluid.


d.
D030335C01
0.719,0.646 1.219,0.99 true 0.646,1.438 0.958,1.594 0.313,0.156 10 false *a 2.531,0.49 2.844,0.646 0.313,0.156 10 false *b 0.49,0.521 0.802,0.677 0.313,0.156 10 false *c
*a Round End
*b Inward
*c Outward


Install the vane pump plates with the round end facing outward.

NOTICE:

Make sure that the vane pump plate are installed in the correct direction.



Hide 4.INSTALL VANE PUMP CAM RING

a.
C106286C01
1.656,0.115 2.385,0.365 true 2.438,0.292 2.75,0.49 0.313,0.198 10 false *a
*a Inscribed Mark


Align the holes of the vane pump cam ring withe the 2 straight pins, and install the vane pump cam ring with the inscribed mark facing upward.

NOTICE:

Make sure that the cam ring is installed in the correct direction.



Hide 44341 5.INSTALL FRONT VANE PUMP SIDE PLATE

a.
C101969

Coat a new O-ring with power steering fluid and install it onto the rear vane pump side plate.


b.
C106287

Align the groove of the cam ring with that of the rear vane pump side plate, and install the rear vane pump side plate.


c.
C106288

Install the wave washer so that its protrusions fit into the slots in the rear vane pump side plate.


Hide 6.INSTALL REAR VANE PUMP HOUSING

a.

Install a new gasket.


b.

Coat a new O-ring with power steering fluid and install it to the rear vane pump housing.


c.
C106279

Install the rear vane pump housing with the 4 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 7.INSPECT ROTATING TORQUE

a.
C106289

Check that pump rotates smoothly without abnormal noise.


b.

Temporarily install the vane pump pulley set nut to the vane pump shaft.


c.

Using a torque wrench, measure the rotating torque.

Standard rotating torque:

0.27 N*m (3 kgf*cm, 2 in.*lbf) or less


If the rotating torque is not as specified, check the installation of the vane pump housing oil seal.


Hide 8.INSTALL FLOW CONTROL VALVE

a.

Coat the compression spring and flow control valve with power steering fluid.


b.
C106278

Install the compression spring and flow control valve.


c.

Coat a new O-ring with power steering fluid and install it onto the pressure port union.


d.

Install the pressure port union to the front vane pump housing.

Torque:
83 N*m (846 kgf*cm, 61 ft.*lbf)


Hide 44337 9.INSTALL POWER STEERING SUCTION PORT UNION

a.

Coat a new O-ring with power steering fluid and install on to the suction port union.


b.
C121998

Install the suction port union to the front vane pump housing with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)