Home › Drivetrain › CLUTCH › CLUTCH UNIT(for R151) › from 2016.01
RM3270E _52 Drivetrain _041682 CLUTCH _0235336 CLUTCH UNIT(for R151) G

CLUTCH  CLUTCH UNIT(for R151)  INSPECTION  


CAUTION / NOTICE / HINT

HINT:

The illustrations in the procedures show a representative example of the shape of the part.


PROCEDURE

Hide 31250 1.INSPECT CLUTCH DISC ASSEMBLY

a.
C322136

Using a vernier caliper, measure the rivet head depth.

Minimum rivet head depth:

0.3 mm (0.0118 in.)


If the depth is less than the minimum, replace the clutch disc assembly.


b.
C322137

Using a dial indicator, check the disc runout.

Maximum runout:

0.8 mm (0.0314 in.)


NOTICE:

Be sure to measure on the correct side of the clutch disc.


If the runout is more than the maximum, replace the clutch disc assembly.


Hide 31210 2.INSPECT CLUTCH COVER ASSEMBLY

a.
C215533C06
1.104,0.271 1.396,0.521 0.292,0.25 10 false *a 0.604,0.948 0.885,1.177 0.281,0.229 10 false *b
*a Width
*b Depth


Using a vernier caliper, measure the depth and width of the worn areas of the diaphragm spring.

Maximum width:

6.0 mm (0.236 in.)


Maximum depth:

0.35 mm (0.0137 in.)


If the depth or width is more than the maximum, replace the clutch cover assembly.


Hide 13405 3.INSPECT FLYWHEEL SUB-ASSEMBLY

a.
Q007250

Using a dial indicator, measure the flywheel runout.

Maximum runout:

0.1 mm (0.00393 in.)


If the runout is more than the maximum, replace the flywheel sub-assembly.


Hide 31230 4.INSPECT CLUTCH RELEASE BEARING ASSEMBLY

a.
N000414

Turn the bearing by hand while applying force in the axial direction and check that the bearing rotates smoothly.

If the bearing sticks or a considerable amount of resistance is felt, replace the release bearing.

HINT:

The bearing is permanently lubricated and requires no cleaning or lubrication.



Hide 33311A 5.INSPECT INPUT SHAFT FRONT BEARING

a.
C322148

Turn the bearing by hand while applying rotational force and check that the bearing rotates smoothly.

If the bearing sticks or a considerable amount of resistance is felt, replace the input shaft front bearing.

HINT:

The bearing is permanently lubricated and requires no cleaning or lubrication.



Hide 33311A 6.REPLACE INPUT SHAFT FRONT BEARING

a.

Remove any 2 diametrically opposite bolts.


b.
C322149N01
1.052,0.917 1.385,0.354 true 1.385,0.167 1.844,0.365 0.458,0.198 10 false SST

Using SST, remove the input shaft front bearing.

SST
09303-35011  


c.
C322150N01
1.167,0.948 1.375,0.344 true 1.375,0.135 1.833,0.333 0.458,0.198 10 false SST

Using SST and a hammer, tap in a new input shaft front bearing.

SST
09304-12012  

HINT:

After installing the bearing to the crankshaft, make sure that it rotates smoothly.



d.

for TR Engine:

i.

Install the new 2 bolts.

Torque:
26.5 N*m (270 kgf*cm, 20 ft.*lbf)

HINT:

The mounting bolts are tightened in 2 progressive steps.



ii.
C284477C02
0.5,1.865 0.813,2.021 0.313,0.156 10 false *a 2.979,0.271 3.292,0.427 0.313,0.156 10 false *b
*a Paint Mark
*b 90°


Mark the mounting bolts with paint.


iii.

Retighten the mounting bolts by 90°.


iv.

Check that the paint marks are now at a 90° angle to the original marked position.



e.

for 5L-E:

i.

Apply adhesive to 2 or 3 threads of each of the bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



ii.

Install 2 bolts.

Torque:
122.5 N*m (1249 kgf*cm, 90 ft.*lbf)