Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _049378 1KD-FTV ENGINE CONTROL _0236318 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0500  Vehicle Speed Sensor  


DESCRIPTION

Vehicles which are equipped with a manual transmission detect the vehicle speed using the speed sensor. The speed sensor transmits a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. The 4-pulse signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter. The signal is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A115899E46
0.594,1.042 1.479,1.438 0.885,0.396 10 false from Wheel Speed Sensor 1.792,1.958 3.01,2.208 1.219,0.25 10 false Skid Control ECU 3.469,1.958 5.344,2.208 1.875,0.25 10 false Combination Meter Assembly 3.115,0.604 3.698,0.813 0.583,0.208 10 false 4-Pulse 5.042,0.604 5.667,0.823 0.625,0.219 10 false 4-Pulse 6.042,1.323 6.448,1.521 0.406,0.198 10 false ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor "A" Conditions (a), (b) and (c) are met for 8 seconds or more (2 trip detection logic):
(a) Engine coolant temperature is higher than 70°C (158°F).
(b) Injection volume is 29.73 mm3/st or more.
(c) No speed signal is input to the ECM.
Conditions (a) and (b) are met for 5 seconds or more (2 trip detection logic):
(a) The fuel-cut operation is being performed.
(b) No speed signal is input to the ECM.
·

Open or short in speedometer circuit

·

Speedometer assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0500 Vehicle Speed

CONFIRMATION DRIVING PATTERN

P0500
DTC Detection Drive Pattern Drive the vehicle at 10 km/h (6.3 mph) or more

WIRING DIAGRAM

A379267E01
0.406,2.313 1.771,2.51 1.365,0.198 10 false Combination Meter 0.406,2.135 0.677,2.302 0.271,0.167 10 false G8 1.156,0.896 1.458,1.083 0.302,0.188 10 false +S 1.438,0.781 1.74,0.969 0.302,0.188 10 false 19 5.01,0.688 5.313,0.875 0.302,0.188 10 false 17 4.938,0.896 5.375,1.104 0.438,0.208 10 false G140 4.958,1.5 5.396,1.708 0.438,0.208 10 false C115 5.073,1.292 5.375,1.479 0.302,0.188 10 false 7 5.396,1.5 5.698,1.688 0.302,0.188 10 false E1 5.365,0.792 5.75,0.958 0.385,0.167 10 false SPD 5.823,2.125 6.219,2.313 0.396,0.188 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Vehicle Speed
50003 234 10

e.

Drive the vehicle.


f.

Read the value displayed on the GTS.


Result:
Result Proceed to
Values displayed on GTS and speedometer display not equal A
Values displayed on GTS and speedometer display equal B



A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-19 (+S) - G140-17 (SPD) Always Below 1 Ω
G8-19 (+S) or G140-17 (SPD) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the combination meter assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.CHECK COMBINATION METER SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - JUNCTION CONNECTOR)

3.CHECK COMBINATION METER SYSTEM
a.

Check the circuits that send vehicle speed signals to this system in the combination meter system.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit


Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at 10 km/h (6.3 mph) or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

g.

Confirm that the pending DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END