Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048930 2KD-FTV ENGINE CONTROL _0236329 ECD SYSTEM D

2KD-FTV ENGINE CONTROL  ECD SYSTEM  FREEZE FRAME DATA  


DESCRIPTION


The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.

HINT:

If it is impossible to duplicate the problem even though a DTC is stored, confirm the freeze frame data.



A301856E12
2.24,0.938 3.083,1.167 0.844,0.229 10 false 0.5 seconds 0.344,0.938 1.188,1.167 0.844,0.229 10 false 0.5 seconds 1.323,0.927 2.167,1.156 0.844,0.229 10 false 0.5 seconds 0.406,2.813 2.844,3.083 2.438,0.271 10 false Freeze frame data recorded 2.375,0.302 3.26,0.563 0.885,0.26 10 false DTC is stored

The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using an GTS, 5 separate sets of freeze frame data can be checked.

·

3 data sets from before the DTC was stored

·

1 data set from when the DTC was stored

·

1 data set from after the DTC was stored


These data sets can be used to simulate the condition of the vehicle from around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.




LIST OF FREEZE FRAME DATA


Powertrain > Engine
Tester Display
Vehicle Speed
Target Idle Engine Speed
Engine Speed
Calculate Load
Atmosphere Pressure
MAP
Coolant Temp
Intake Air
Engine Run Time
Initial Engine Coolant Temp
Initial Intake Air Temp
Battery Voltage
Alternate Duty Ratio
Glow Relay Request
Glow Indicator Supported
Glow Indicator
Accel Position
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
Target Throttle Position Supported
Target Throttle Position
Target Throttle Position #2 Supported
Target Throttle Position #2
Actual Throttle Position Supported
Actual Throttle Position
Actual Throttle Position #2 Supported
Actual Throttle Position #2
Throttle Motor DUTY
Throttle Close Learning Val.
Throttle Sensor Volt %
Injection Volume
Inj. FB Vol. for Idle
Inj Vol Feedback Learning
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Pilot 1 Injection Period
Pilot 2 Injection Period
Main Injection Period
After Injection Period
Pilot 1 Injection Timing
Pilot 2 Injection Timing
Main Injection Timing
After Injection Timing
Pilot Quantity Learning
Injector Pilot Quantity Learning
Actuator Pilot Quantity Learning
Temperature Pilot Quantity Learning
Catalyst Pilot Quantity Learning
Injection Pressure Correction
Injection EDU Relay Request
Target Common Rail Pressure Supported
Target Common Rail Pressure
Common Rail Pressure Supported
Common Rail Pressure
Fuel Temperature Supported
Fuel Temperature
Target Pump SCV Current
Pump SCV Learning Value
Pump SCV Status
Pump SCV Duty Request
Pressure Discharge Valve
Starter Signal
Clutch Switch
Clutch Start SW
Stop Light Switch
A/C Signal
Idle Up SW
Immobiliser Communication
TC Terminal
Time after DTC Cleared
Distance from DTC Cleared
Warmup Cycle Cleared DTC
Dist Batt Cable Disconnect
TC and TE1
Total Distance Traveled
Engine Speed (Starter Off)
Starter Count
Run Dist of Previous Trip
Electric Duty Feedback Value
A/C Duty Feedback Value
PS Duty Feedback Value
Idle Injection Volume (Min)
Engine Starting Time
Minimum Engine Speed
ACT VSV
Brake Override System