Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _041671 1GD-FTV ENGINE CONTROL _0236339 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P2610  ECM / PCM Internal Engine Off Timer Performance  


DESCRIPTION

The soak timer operates after the engine switch is turned off. When a certain amount of time has elapsed after turning the engine switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.

A359718E01
3.146,1.302 4.688,1.677 1.542,0.375 10 false Certification ECU (Smart Key ECU Assembly) 3.625,0.896 4.042,1.104 0.417,0.208 10 false IG1D 5.063,0.594 6.156,0.792 1.094,0.198 10 false Soak Timer IC 4.865,1.875 5.958,2.073 1.094,0.198 10 false IGSW 2.26,2.344 3.354,2.542 1.094,0.198 10 false IG2 0.698,2.156 1.792,2.354 1.094,0.198 10 false AM2 NO. 2 4.865,2.385 5.313,2.573 0.448,0.188 10 false +B3 4.875,2.813 5.323,3 0.448,0.188 10 false +B2 4.885,3.208 5.333,3.396 0.448,0.188 10 false +B 5.469,2.542 6.615,2.74 1.146,0.198 10 false Power Source IC 1.896,3.51 3.042,3.708 1.146,0.198 10 false EFI-MAIN NO. 1 2.875,4.531 4.021,4.729 1.146,0.198 10 false EFI-MAIN NO. 1 1.969,5.031 4.042,5.25 2.073,0.219 10 false Instrument Panel Junction Block 5.052,3.854 6.531,4.042 1.479,0.188 10 false Main Relay Control IC 4.385,4.094 5.479,4.292 1.094,0.198 10 false MREL 5.75,4.938 6.219,5.146 0.469,0.208 10 false ECM 0.427,3.76 0.896,3.969 0.469,0.208 10 false J/B-B 0.427,4.375 1.385,4.583 0.958,0.208 10 false FL MAIN 3.0W 0.604,5.031 1.563,5.24 0.958,0.208 10 false Battery 3.448,2.167 4.542,2.365 1.094,0.198 10 false IG2 NO. 1

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2610 ECM / PCM Internal Engine Off Timer Performance ECM internal malfunction (2 trip detection logic). ECM Comes on DTC stored

MONITOR DESCRIPTION

·

While the engine is running, the ECM monitors the synchronization of the soak timer and the CPU clock. If these two are not synchronized, the ECM interprets this as a malfunction, illuminates the MIL and stores the DTC.

·

If the soak timer activates the ECM even though only a short amount of time has elapsed since the engine switch was turned off, or if the soak timer does not activate the ECM even though a considerable amount of time has elapsed since the engine switch was turned off, the ECM determines that the soak timer is malfunctioning, illuminates the MIL and stores a DTC the next time the engine switch is turned to on (IG).


CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:
·

DTC P2610 is stored if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is necessary.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

2.CHECK WHETHER DTC OUTPUT RECURS
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the engine switch off for 30 seconds or more.


f.

Start the engine and wait for 10 minutes or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

If no pending DTC is output, the repair has been successfully completed.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END