The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the diesel throttle body assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2141 | Diesel Throttle Motor Circuit Low | Both of the following conditions are met for 2.0 seconds (1 trip detectionlogic):
·
The throttle actuator duty cycle is 80% or higher. ·
The throttle actuator current is less than 0.5 A. |
·
Open or short in throttle actuator circuit ·
Diesel throttle body assembly ·
ECM |
Comes on | DTC stored |
| P2142 | Diesel Throttle Motor Circuit High | A throttle actuator current of 8 A or higher or the ECM internal circuit temperature of 150 to 160°C (302 to 320°F) or higher is detected.
(1 trip detection logic). |
·
Open or short in throttle actuator circuit ·
Diesel throttle body assembly ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P2141 | Throttle Motor DUTY |
| P2142 |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P2141 | Idle the engine for 5 seconds or more |
| P2142 |
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Remove the electric diesel throttle body assembly.
Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>DIESEL THROTTLE BODY>REMOVAL
| *a | Component without harness connected
(Diesel throttle body assembly) |
Measure the resistance according to the value(s) inthe table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (M+) - 1 (M-) | Always | No short or open circuit |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the diesel throttle body assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Y1-2 (M+) - C41-6 (M+) | Always | Below 1 Ω |
| Y1-1 (M-) - C41-5 (M-) | Always | Below 1 Ω |
| Y1-2 (M+) or C41-6 (M+) - Body ground and other terminals | Always | 10 kΩ or higher |
| Y1-1 (M-) or C41-5 (M-) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the diesel throttle body assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for 30 seconds.
Start the engine.
Idle the engine for 5 seconds or more.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the diesel throttle body assembly.
Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>DIESEL THROTTLE BODY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT