Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048922 2GD-FTV ENGINE CONTROL _0236344 ECD SYSTEM C

2GD-FTV ENGINE CONTROL  ECD SYSTEM  P0116  Engine Coolant Temperature Circuit Range / Performance  


DESCRIPTION

A thermistor is built into the engine coolant temperature sensor and it changes its resistance value according to the engine coolant temperature.

The structure of the sensor and connection to the ECM is the same as that of the intake air temperature sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0116 Engine Coolant Temperature Circuit Range / Performance Condition 1:
·

The engine coolant temperature is between -40°C (-40°F) and 60°C (140°F) at engine start, and conditions (a) and (b) are met (2 trip detection logic):

1.

Vehicle is driven at varying speeds (accelerating and decelerating) for 600 seconds.

2.

Engine coolant temperature remains within 3°C (5.4°F) of the engine starting temperature.



Condition 2:
·

The engine coolant temperature is higher than 60°C (140°F) at engine start, and conditions (a) and (b) are met (6 trip detection logic):

1.

Vehicle is driven at varying speeds (accelerating and decelerating) for 600 seconds.

2.

Engine coolant temperature remains within 1°C (1.8°F) of the engine starting temperature.



·

Thermostat

·

Engine coolant temperature sensor


Comes on DTC stored

Related Data List
DTC No. Data List
P0116 Coolant Temp

HINT:

If DTC P0116 is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0116 Condition 1:
City driving for 10 minutes or more after engine start with engine coolant temperature between -40°C (-40°F) and 60°C (140°F)
Condition 2:
City driving for 10 minutes or more after engine start with engine coolant temperature higher than 60°C (140°F)

MONITOR DESCRIPTION

The engine coolant temperature sensor is used to monitor the engine coolant temperature. The engine coolant temperature sensor has a thermistor that varies its resistance depending on the temperature of the engine coolant. When the coolant temperature is low, the resistance of the thermistor increases.

When the sensor voltage output varies slightly, the ECM interprets this as afault in the engine coolant temperature sensor and sets a DTC.

Examples:

1.

Upon starting the engine, the engine coolant temperature is between -40°C (-40°F) and 60°C (140°F). If, after driving for a few minutes, the engine coolant temperature still remains within 3°C (5.4°F) of the starting temperature, a DTC is stored (2 trip detection logic).

2.

Upon starting the engine, the engine coolant temperature is more than 60°C (140°F). If, after driving for a few minutes, the engine coolant temperature still remains within 1°C (1.8°F) of the starting temperature, a DTC is stored (6 trip detection logic).


CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0116)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
P0116 is output A
P0116 and other DTCs are output B




A

2.INSPECT THERMOSTAT

B

2.INSPECT THERMOSTAT
a.

b.

Measure the valve opening temperature of the thermostat.

Standard opening temperature:

80 to 84°C (176 to 183°F)


HINT:

In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.




Result:
Proceed to
OK
NG



OK

3.REPLACE ENGINE COOLANT TEMPERATURE SENSOR

NG

5.REPLACE THERMOSTAT
3.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Replace the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

d.

Check that the engine coolant temperature is 60°C (140°F) or less.


e.

Start the engine.


f.

Drive the vehicle for a total of 10 minutes or more.


g.

Check that the engine coolant temperature changes by 1°C (1.8°F) or more.


Result:
Proceed to
NEXT



NEXT

END

5.REPLACE THERMOSTAT
a.

Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED