Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048922 2GD-FTV ENGINE CONTROL _0236344 ECD SYSTEM C

2GD-FTV ENGINE CONTROL  ECD SYSTEM  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  


DESCRIPTION

The throttle position sensor is mounted on the diesel throttle body assembly and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.

When the throttle valve is fully closed, a voltage of approximately 0.4 to 1.0 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.6 to 4.2 V when the throttle valve is fully opened.

The ECM determines the vehicle driving conditions from the signals input to its VLU terminal. The data is one of the pieces of information used for EGR control, etc.

A298509E02
2.073,2.635 2.323,2.635 2.323,2.635 2.74,2.365 true 2.396,0.51 2.563,0.51 2.563,0.51 2.729,1.156 true 3.281,0.406 3.063,0.406 3.063,0.406 2.875,1.677 true 4.698,2.771 5.156,2.969 0.458,0.198 10 false ECM 3.844,2.177 4.302,2.375 0.458,0.198 10 false EVLU 3.927,1.563 4.385,1.76 0.458,0.198 10 false VLU 3.833,0.948 4.292,1.146 0.458,0.198 10 false VCVL 3.49,0.948 3.948,1.146 0.458,0.198 10 false VC 3.49,1.563 3.948,1.76 0.458,0.198 10 false VTA 3.49,2.167 3.948,2.365 0.458,0.198 10 false E2 1.563,2.552 2.135,2.781 0.573,0.229 10 false Magnet 1.885,0.417 2.458,0.646 0.573,0.229 10 false Magnet 3.344,0.323 3.917,0.552 0.573,0.229 10 false Hall IC 4.729,0.885 5.302,1.115 0.573,0.229 10 false 5 V 2.052,2.792 3.604,3.073 1.552,0.281 10 false Throttle Position Sensor

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input Throttle position sensor output (VLU) is below 0.2 V for 3 seconds (1 trip detection logic).
·

Throttle position sensor

·

Open or short in VLU circuit

·

Open in VC circuit

·

ECM


Comes on DTC stored
P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input Throttle position sensor output (VLU) is higher than 4.8 V for 3 seconds (1 trip detection logic).
·

Throttle position sensor

·

Open in E2 circuit

·

VC and VLU circuits are short-circuited

·

ECM


Comes on DTC stored

HINT:

If DTC P0122 and/or P0123 is stored, the following symptoms may appear:


- Intake booming noise

- Black smoke

- Lack of power

- Vibration at engine stop

- Turbo overspeed, turbo damage


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0122 Ignition switch ON for 3 seconds or more
P0123

MONITOR DESCRIPTION

When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

A302636E02
2.104,1.167 2.313,1.052 false 2.094,2.74 2.302,2.625 false 3.313,1 3.469,0.417 3.469,0.417 3.615,0.417 false 4.604,2.656 4.719,3.031 4.719,3.031 4.823,3.031 false 0.146,1.365 1.635,1.781 1.49,0.417 10 false Throttle Position Sensor Output Voltage (V) 2.042,0.625 2.563,0.844 0.521,0.219 10 false Closed 1.99,0.885 2.333,1.063 0.344,0.177 10 false 5.00 1.802,1.115 2.146,1.292 0.344,0.177 10 false 4.80 2,1.365 2.396,1.542 0.396,0.177 10 false 4.13 2,2.406 2.344,2.583 0.344,0.177 10 false 0.69 1.844,2.75 2.188,2.927 0.344,0.177 10 false 0.20 2.677,2.729 3.917,2.948 1.24,0.219 10 false Range of Operation 3.656,0.333 4.552,0.573 0.896,0.24 10 false Stores P0123 3.938,0.604 4.458,0.823 0.521,0.219 10 false Open 4.865,2.948 5.823,3.177 0.958,0.229 10 false Stores P0122 2.281,3.177 2.438,3.344 0.156,0.167 10 false 0 4.083,3.177 4.396,3.344 0.313,0.167 10 false 86° 2.656,3.385 4.531,3.635 1.875,0.25 10 false Throttle Valve Opening Angle

WIRING DIAGRAM

A348534E02
5.063,1.917 5.521,2.115 0.458,0.198 10 false C40 5.073,2.438 5.531,2.635 0.458,0.198 10 false C41 5.073,2.958 5.531,3.156 0.458,0.198 10 false C41 5.052,0.875 5.51,1.073 0.458,0.198 10 false C40 5.063,1.385 5.521,1.583 0.458,0.198 10 false C40 5.406,0.99 6.094,1.188 0.688,0.198 10 false VCVL 5.406,1.51 5.865,1.708 0.458,0.198 10 false VLU 5.406,2.042 5.865,2.24 0.458,0.198 10 false EVLU 5.135,2.24 5.344,2.469 0.208,0.229 10 false 6 2.167,1 2.625,1.198 0.458,0.198 10 false 5 1.906,2.969 2.365,3.167 0.458,0.198 10 false M- 1.875,2.448 2.333,2.646 0.458,0.198 10 false M+ 1.885,2.042 2.167,2.271 0.281,0.229 10 false E2 1.802,1.51 2.26,1.708 0.458,0.198 10 false VTA 1.885,0.969 2.177,1.188 0.292,0.219 10 false VC 0.604,3.667 1.063,3.865 0.458,0.198 10 false Y1 0.594,3.896 2.75,4.125 2.156,0.229 10 false Diesel Throttle Body Assembly 5.792,3.781 6.25,3.979 0.458,0.198 10 false ECM 5.406,2.958 5.865,3.156 0.458,0.198 10 false M- 5.406,2.448 5.865,2.646 0.458,0.198 10 false M+ 2.167,2.052 2.375,2.281 0.208,0.229 10 false 3 2.177,2.573 2.385,2.802 0.208,0.229 10 false 2 2.167,3.104 2.375,3.333 0.208,0.229 10 false 1 2.167,1.521 2.375,1.75 0.208,0.229 10 false 6 5.146,2.76 5.604,2.958 0.458,0.198 10 false 5 5.094,0.656 5.552,0.854 0.458,0.198 10 false 29 5.104,1.188 5.563,1.385 0.458,0.198 10 false 21 5.104,1.708 5.563,1.906 0.458,0.198 10 false 20

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ECM (POWER SOURCE OF THROTTLE POSITION SENSOR)
a.
A257437C15
1.281,0.875 1.677,1.125 0.396,0.25 1.99,2.313 1.625,1.698 true 1.375,2.313 1.573,1.646 true 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 1.354,0.917 1.729,1.125 0.375,0.208 10 false C40 1.99,2.354 2.698,2.594 0.708,0.24 10 false 29 (VCVL) 0.823,2.354 1.656,2.563 0.833,0.208 10 false 20 (EVLU)
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C40-29 (VCVL) - C40-20 (EVLU) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

2.INSPECT THROTTLE POSITION SENSOR VOLTAGE (VLU VOLTAGE)

NG

11.REPLACE ECM
2.INSPECT THROTTLE POSITION SENSOR VOLTAGE (VLU VOLTAGE)
a.
A257437C16
1.281,0.875 1.688,1.115 0.406,0.24 1.354,2.302 1.531,1.635 true 1.844,2.281 1.573,1.635 true 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 1.365,0.906 1.823,1.177 0.458,0.271 10 false C40 0.854,2.323 1.677,2.573 0.823,0.25 10 false 21 (VLU) 1.802,2.313 2.615,2.521 0.813,0.208 10 false 20 (EVLU)
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C40-21 (VLU) - C40-20 (EVLU) Ignition switch ON 3.6 to 4.2 V



Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT

NG

4.CHECK HARNESS AND CONNECTOR
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON for 3 seconds or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTCs are not output A
DTC P0122 or P0123 is output B




A

B

4.CHECK HARNESS AND CONNECTOR
a.
A275086C06
0.51,1.063 0.906,1.365 0.396,0.302 1.927,1.417 2.375,1.771 true 1.198,1.833 1.615,1.417 true 0.333,0.438 0.646,0.594 0.313,0.156 10 false *a 0.615,1.135 0.927,1.333 0.313,0.198 10 false Y1 2.427,1.813 2.74,2.01 0.313,0.198 10 false VC 1.01,1.854 1.323,2.052 0.313,0.198 10 false E2
*a Front view of wire harness connector
(to Diesel Throttle Body Assembly)


Disconnect the diesel throttle body assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Y1-5 (VC) - Y1-3 (E2) Ignition switch ON 4.5 to 5.5 V



c.

Reconnect the throttle position sensor connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the diesel throttle body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y1-6 (VTA) - C40-21 (VLU) Always Below 1 Ω
Y1-3 (E2) - C40-20 (EVLU) Always Below 1 Ω
Y1-6 (VTA) or C40-21 (VLU) - Body ground and other terminals Always 10 kΩ or higher
Y1-3 (E2) or C40-20 (EVLU) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the diesel throttle body assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

6.CHECK ECM (CHECK RESISTANCE)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK ECM (CHECK RESISTANCE)
a.

Disconnect the diesel throttle body assembly connector.


b.
A275086C08
0.51,1.063 0.906,1.365 0.396,0.302 1.927,1.417 1.76,1.844 true 1.198,1.833 1.615,1.417 true 2.052,1.427 2.292,1.833 true 0.333,0.438 0.646,0.594 0.313,0.156 10 false *a 0.615,1.135 0.927,1.333 0.313,0.198 10 false Y1 1.646,1.865 1.958,2.063 0.313,0.198 10 false VC 1.01,1.854 1.323,2.052 0.313,0.198 10 false E2 2.292,1.865 2.823,2.063 0.531,0.198 10 false VTA
*a Front view of wire harness connector
(to Diesel Throttle Body Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
Y1-5 (VC) - Y1-6 (VTA) Ignition switch off No short or open circuit
Y1-6 (VTA) - Y1-3 (E2)



c.

Reconnect the diesel throttle body assembly connector.


Result:
Proceed to
OK
NG



OK

7.REPLACE DIESEL THROTTLE BODY ASSEMBLY

NG

8.REPLACE ECM
7.REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Replace the diesel throttle body assembly.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>DIESEL THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON for 3 seconds or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED