Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048922 2GD-FTV ENGINE CONTROL _0236344 ECD SYSTEM C

2GD-FTV ENGINE CONTROL  ECD SYSTEM  P0489  Exhaust Gas Recirculation Control Circuit Low  P0490  Exhaust Gas Recirculation Control Circuit High  


DESCRIPTION

The EGR actuator is operated by the ECM and opens and closes the EGR valve using gears. The opening angle of the EGR valve is detected by the EGR position sensor, which is mounted on the electric EGR control valve assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0489 Exhaust Gas Recirculation Control Circuit Low Both of the following conditions are met for 2.0 seconds (1 trip detectionlogic):
·

The EGR actuator duty cycle is 80% or higher.

·

EGR actuator current is below 0.5 A.


·

Open or short in EGR actuator circuit

·

Electric EGR control valve assembly

·

ECM


Comes on DTC stored
P0490 Exhaust Gas Recirculation Control Circuit High An EGR actuator current of 8 A or higher or the ECM internal circuit temperature of 150 to 160°C (302 to 320°F) or higher is detected.
(1 trip detection logic):
·

Open or short in EGR actuator assembly circuit

·

Electric EGR control valve assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0489
·

Actual EGR Valve Pos

·

Target EGR Valve Pos


P0490

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0489 Idle the engine for 5 seconds or more
P0490

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY (RESISTANCE OF EGR ACTUATOR)
a.

Remove the electric EGR control valve assembly.

Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>EGR VALVE>REMOVAL


b.
A351114C01
1.323,1.156 1.5,1.729 1.5,1.729 1.604,1.729 true 0.938,1.156 0.854,1.729 0.854,1.729 0.719,1.729 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.667,1.646 1.979,1.844 0.313,0.198 10 false M+ 0.531,1.656 0.844,1.854 0.313,0.198 10 false M-
*a Component without harness connectoted
(Electric EGR Control Valve Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (M-) - 4 (M+) Always No short or open circuit



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ELECTRIC EGR CONTROL VALVE ASSEMBLY - ECM)

NG

6.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (ELECTRIC EGR CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the electric EGR control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C37-4 (M+) - C40-6 (EGM+) Always Below 1 Ω
C37-5 (M-) - C40-7 (EGM-) Always Below 1 Ω
C37-4 (M+) or C40-6 (EGM+) - Body ground and other terminals Always 10 kΩ or higher
C37-5 (M-) or C40-7 (EGM-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the electric EGR control valve assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

Idle the engine for 5 seconds or more


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

6.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly.

Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>EGR VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED