Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048922 2GD-FTV ENGINE CONTROL _0236344 ECD SYSTEM C

2GD-FTV ENGINE CONTROL  ECD SYSTEM  P052F  Glow Plug Control Module System Voltage  P0683  Glow Plug Control Module to PCM Communication Circuit  


DESCRIPTION

The glow system consists of the glow plug controller, glow plugs and ECM. The glow plug controller turns on the glow plug of each cylinder according to the duty command signal from the ECM in order to maintain optimal engine temperatures. The glow plugs can be controlled according to the engine coolant temperature at engine start by using duty signals. This helps induce ignition under low temperatures and prevent rough idle after starting the engine.

The glow plug controller contains a self-diagnosis function. When the glow plug controller detects an internal malfunction, it sends a signal indicating the malfunction to the ECM. When the ECM receives this signal, it illuminates the MIL and stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P052F Glow Plug Control Module System Voltage The glow plug controller recognizes the battery voltage as being 18.4 V or higher 3 times or more when the glow plugs are on (2 trip detection logic). Glow plug controller Comes on DTC stored
P0683 Glow Plug Control Module to PCM Communication Circuit When the glow plugs are on, the ECM detects that there is no output from the glow plug control unit for 3 seconds even though the ECM outputs an SI signal ("ON" command signal) (2 trip detection logic).
·

Open or short circuit in ground wire

·

Open or short circuit in battery wire

·

Open in SI wire

·

SI wire short circuit to ground or battery

·

Open in DI wire

·

DI wire short circuit to ground or battery

·

Low battery voltage

·

Glow plug controller

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P052F Enter check mode
P0683

WIRING DIAGRAM

A348537E12
6.323,8.198 6.729,8.396 0.406,0.198 10 false ECM 5.802,0.521 6.094,0.688 0.292,0.167 10 false C39 5.802,0.938 6.094,1.104 0.292,0.167 10 false C39 5.792,4.292 6.083,4.458 0.292,0.167 10 false G49 5.792,7.594 6.083,7.76 0.292,0.167 10 false G49 5.833,0.344 6.031,0.51 0.198,0.167 10 false 11 5.833,0.76 6.031,0.927 0.198,0.167 10 false 10 5.833,4.125 6.031,4.292 0.198,0.167 10 false 15 5.844,7.417 6.042,7.583 0.198,0.167 10 false 14 1.604,0.521 1.896,0.688 0.292,0.167 10 false C46 1.604,0.927 1.896,1.094 0.292,0.167 10 false C46 1.604,1.354 1.896,1.521 0.292,0.167 10 false C45 1.604,1.771 1.896,1.938 0.292,0.167 10 false C45 1.604,2.188 1.896,2.354 0.292,0.167 10 false C44 1.604,2.604 1.896,2.771 0.292,0.167 10 false C44 1.604,3.49 1.896,3.656 0.292,0.167 10 false C46 1.604,3.948 1.896,4.115 0.292,0.167 10 false A44 1.594,4.406 1.885,4.573 0.292,0.167 10 false C46 0.563,4.813 1.823,5.01 1.26,0.198 10 false Glow Plug Controller 1.677,4.229 1.823,4.396 0.146,0.167 10 false 1 1.698,0.344 1.844,0.51 0.146,0.167 10 false 3 1.698,0.75 1.844,0.917 0.146,0.167 10 false 5 1.698,1.167 1.844,1.333 0.146,0.167 10 false 1 1.698,1.583 1.844,1.75 0.146,0.167 10 false 2 1.698,2.01 1.844,2.177 0.146,0.167 10 false 1 1.708,2.427 1.854,2.594 0.146,0.167 10 false 2 3.104,1.25 3.25,1.417 0.146,0.167 10 false 1 3.104,1.677 3.25,1.844 0.146,0.167 10 false 2 1.698,3.302 1.844,3.469 0.146,0.167 10 false 4 3.104,2.51 3.25,2.677 0.146,0.167 10 false 4 1.698,3.76 1.844,3.927 0.146,0.167 10 false 1 3.104,2.094 3.25,2.26 0.146,0.167 10 false 3 3.24,2.865 3.531,3.031 0.292,0.167 10 false C47 3.24,3.021 3.927,3.208 0.688,0.188 10 false Glow Plug 6.146,0.531 6.573,0.688 0.427,0.156 10 false GLDO 6.146,0.938 6.521,1.094 0.375,0.156 10 false GLDI 1.365,0.531 1.552,0.688 0.188,0.156 10 false SI 1.365,0.927 1.552,1.083 0.188,0.156 10 false DI 3.302,1.344 3.719,1.5 0.417,0.156 10 false GLW1 3.292,1.76 3.708,1.917 0.417,0.156 10 false GLW2 3.292,2.177 3.708,2.333 0.417,0.156 10 false GLW3 3.292,2.583 3.708,2.74 0.417,0.156 10 false GLW4 1.26,1.354 1.552,1.521 0.292,0.167 10 false GL1 1.26,1.771 1.552,1.938 0.292,0.167 10 false GL2 1.26,2.188 1.552,2.354 0.292,0.167 10 false GL3 1.26,2.604 1.552,2.771 0.292,0.167 10 false GL4 1.323,3.49 1.552,3.656 0.229,0.167 10 false +B 1.167,3.948 1.552,4.115 0.385,0.167 10 false BATT 1.229,4.406 1.552,4.573 0.323,0.167 10 false GND 3.167,4.604 3.635,4.771 0.469,0.167 10 false GLOW 2.979,3.854 3.125,4.021 0.146,0.167 10 false 3 2.979,4.208 3.125,4.375 0.146,0.167 10 false 1 3.75,3.854 3.896,4.021 0.146,0.167 10 false 5 3.75,4.208 3.896,4.375 0.146,0.167 10 false 2 6.146,4.302 6.563,4.458 0.417,0.156 10 false GREL 6.146,7.583 6.563,7.74 0.417,0.156 10 false MREL 1,5.594 1.469,5.76 0.469,0.167 10 false GLOW 1.031,5.323 1.177,5.49 0.146,0.167 10 false 1 1.333,5.323 1.479,5.49 0.146,0.167 10 false 2 1.01,6.25 1.375,6.417 0.365,0.167 10 false J/B-B 1.021,5.979 1.167,6.146 0.146,0.167 10 false 1 1.302,5.979 1.448,6.146 0.146,0.167 10 false 2 2.177,6.094 2.396,6.26 0.219,0.167 10 false 2B 2.188,6.458 2.406,6.625 0.219,0.167 10 false 2J 2.188,7.594 2.406,7.76 0.219,0.167 10 false 2K 5.167,6.094 5.385,6.26 0.219,0.167 10 false 2G 5.167,6.458 5.385,6.625 0.219,0.167 10 false 2P 5.167,7.229 5.385,7.396 0.219,0.167 10 false 2G 5.167,7.583 5.385,7.75 0.219,0.167 10 false 2P 2.198,5.927 2.344,6.094 0.146,0.167 10 false 1 2.219,6.292 2.365,6.458 0.146,0.167 10 false 5 2.24,7.417 2.385,7.583 0.146,0.167 10 false 3 5.208,5.927 5.354,6.094 0.146,0.167 10 false 3 5.219,6.292 5.365,6.458 0.146,0.167 10 false 9 5.219,7.063 5.365,7.229 0.146,0.167 10 false 7 5.208,7.417 5.354,7.583 0.146,0.167 10 false 8 3.052,5.979 3.198,6.146 0.146,0.167 10 false 1 3.323,5.979 3.469,6.146 0.146,0.167 10 false 2 4.583,5.979 4.729,6.146 0.146,0.167 10 false 1 4.854,5.979 5,6.146 0.146,0.167 10 false 2 3.052,7.115 3.198,7.281 0.146,0.167 10 false 1 3.323,7.115 3.469,7.281 0.146,0.167 10 false 2 4.469,6.229 5.125,6.396 0.656,0.167 10 false EFI NO. 1 3.635,6.76 4.688,6.917 1.052,0.156 10 false EFI-MAIN NO. 2 3.615,7.896 4.667,8.052 1.052,0.156 10 false EFI-MAIN NO. 1 2.729,6.24 3.906,6.438 1.177,0.198 10 false EFI-MAIN NO. 2 2.771,7.365 3.813,7.531 1.042,0.167 10 false EFI-MAIN NO. 1 2.792,8.219 4.802,8.406 2.01,0.188 10 false Instrument Panel Junction Block 0.49,6.948 1.094,7.115 0.604,0.167 10 false FL MAIN 0.698,7.854 1.302,8.021 0.604,0.167 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
P0683 is output A
P052F is output B




A

2.CHECK GLOW PLUG CONTROLLER (POWER SOURCE CIRCUIT)

B

12.REPLACE GLOW PLUG CONTROLLER
2.CHECK GLOW PLUG CONTROLLER (POWER SOURCE CIRCUIT)
a.
A241954C09
0.542,1 1.01,1.271 0.469,0.271 1.917,1.677 1.76,1.188 true 0.125,0.146 0.438,0.344 0.313,0.198 10 false *a 0.646,1.052 1,1.271 0.354,0.219 10 false C46 1.885,1.667 2.198,1.865 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Glow Plug Controller)


Disconnect the glow plug controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C46-4 (+B) - Body ground Ignition switch ON 11 to 14 V
C46-4 (+B) - Body ground Ignition switch off Below 0.5 V



c.

Reconnect the glow plug controller connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - BODY GROUND)

NG

9.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - INSTRUMENT PANEL JUNCTION BLOCK)
3.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - BODY GROUND)
a.

Disconnect the glow plug controller connector.


b.
A241954C13
0.542,1 1.01,1.271 0.469,0.271 1.302,1.646 1.49,1.188 true 0.125,0.146 0.438,0.344 0.313,0.198 10 false *a 0.625,1.052 0.979,1.271 0.354,0.219 10 false C46 1.146,1.667 1.635,1.875 0.49,0.208 10 false GND
*a Front view of wire harness connector
(to Glow Plug Controller)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C46-1 (GND) - Body ground Always Below 1 Ω



c.

Reconnect the glow plug controller connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - ECM)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - ECM)
a.

Disconnect the glow plug controller connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C46-3 (SI) - C39-11 (GLDO) Always Below 1 Ω
C46-5 (DI) - C39-10 (GLDI) Always Below 1 Ω
C46-3 (SI) or C39-11 (GLDO) - Body ground and other terminals Always 10 kΩ or higher
C46-5 (DI) or C39-10 (GLDI) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the glow plug controller connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE GLOW PLUG CONTROLLER

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE GLOW PLUG CONTROLLER
a.

Replace the glow plug controller.

Click hereEngine / Hybrid System>2GD-FTV STARTING>GLOW PLUG CONTROLLER>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode.

Powertrain > Engine and ECT > Utility
Tester Display
Check Mode
50005 234 1

g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Check for DTCs in check mode.



Result:
Proceed to
OK
NG



OK

END

NG

7.REPLACE ECM
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode.

Powertrain > Engine and ECT > Utility
Tester Display
Check Mode
50005 234 1

g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Check for DTCs in check mode.



Result:
Proceed to
NEXT



NEXT

END

9.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - INSTRUMENT PANEL JUNCTION BLOCK)
a.

Disconnect the glow plug controller connector.


b.

Remove the instrument panel junction block connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C46-4 (+B) - 2G-3 Always Below 1 Ω
C46-4 (+B) or 2G-3 - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the glow plug controller connector.


e.

Reinstall the instrument panel junction block connector.


Result:
Proceed to
OK
NG



OK

10.CHECK CHARGING SYSTEM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.CHECK CHARGING SYSTEM
a.

Check the charging system and perform repairs as necessary.

Click herePower Source / Network>2GD-FTV BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPLACE GLOW PLUG CONTROLLER
a.

Replace the glow plug controller.

Click hereEngine / Hybrid System>2GD-FTV STARTING>GLOW PLUG CONTROLLER>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode.

Powertrain > Engine and ECT > Utility
Tester Display
Check Mode
50005 234 1

g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Check for DTCs in check mode.



Result:
Proceed to
NEXT



NEXT

END