Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048922 2GD-FTV ENGINE CONTROL _0236344 ECD SYSTEM C

2GD-FTV ENGINE CONTROL  ECD SYSTEM  P062F  Internal Control Module EEPROM Error  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P062F Internal Control Module EEPROM Error When any condition below is met (1 trip detection logic):
·

Injector compensation code is not registered.

·

Wrong injector compensation code is registered.

·

Injector pilot quantity learning value is not registered.

·

Crank Time Compensation Learning value is not registered.*


*: When this malfunction occurs, the MIL does not illuminate.
·

Injector compensation code

·

Injector pilot quantity learning value

·

Crank time compensation learning value

·

ECM


Comes on DTC stored

NOTICE:
·

When an injector assembly is replaced, the new injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM.

·

Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly. If an incorrect injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

·

When an injector assembly is replaced, perform pilot quantity learning. When the ECM is replaced, all of the existing pilot quantity learning values must be input into the new ECM.



HINT:

When replacing the ECM with a new one, if the injector compensation code and pilot quantity learning value are not entered, DTC P062F will be stored.


When replacing the ECM with a new one, input all learning values and codes into the new ECM as follows:


a.

Prior to replacing the ECM, use the GTS to read and save each learning value and code from the original ECM (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION).


b.

After installing a new ECM, input the saved learning values and codes into the new ECM using the GTS (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION).


c.

Turn the ignition switch off and turn the GTS off.


d.

Wait for at least 30 seconds.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Clear DTC P062F stored in the ECM using the GTS.

Powertrain > Engine and ECT > Clear DTCs
50002 234
HINT:
·

Each injector assembly has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the injector compensation codes to balance the different fuel injections between each injector assembly.

·

When you first turn ON the ignition switch after replacing the ECM and other component(s), DTC P062F is stored. Manually clear the DTC upon completion of compensation code registration.

Replacement Part Utility Item
ECM
·

Learning Values Save (Click here (Click here))

·

Learning Values Write (Click here (Click here))


Injector Assembly
·

Input Injector Compensation Code (Click here (Click here))

·

Pilot Quantity Learning (Click here (Click here))







CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P062F Ignition switch ON for 1 second or more

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.LEARNING VALUES CONFIRMATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values confirmation.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Learning Values Confirmation
50005 234 242
Result:
Result Proceed to
The injector compensation codes are not input A
The injector compensation codes registered in the ECM are different than the codes imprinted on the injectors B
The pilot quantity learning values are set to the default values C
Except above D


HINT:

When the pilot quantity learning values are set to the default values, "7FFF" is displayed.




A

2.PERFORM LEARNING VALUES SAVE

B

9.REGISTER INJECTOR COMPENSATION CODE

C

10.PERFORM PILOT QUANTITY LEARNING

D

4.CHECK DTC OUTPUT
2.PERFORM LEARNING VALUES SAVE
HINT:

When replacing the ECM, after performing "Learning Values Save" to save the learned values from the old ECM using the GTS and replacing the old ECM with a new one, "Learning Values Write" was not performed using the GTS causing this DTC to be output.


a.

Install the old ECM.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Save.


e.

Perform the Learning Values Save.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Learning Values Save
50005 234 240

Result:
Result Proceed to
Learning Values Save is complete A
Learning Values Save is fail B



A

3.PERFORM LEARNING VALUES WRITE

B

1.LEARNING VALUES CONFIRMATION
3.PERFORM LEARNING VALUES WRITE
a.

Remove the old ECM.


b.

Install a new ECM.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Write.


e.

Perform the Learning Values Write.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Learning Values Write
50005 234 241

Result:
Result Proceed to
Learning Values Save is complete A
Learning Values Save is fail B



A

4.CHECK DTC OUTPUT

B

7.PERFORM LEARNING VALUES SAVE
4.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off and leave the vehicle for 30 seconds or more.


d.

Turn the ignition switch to ON for 1 second.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
No DTC is output A
P062F is output B




A

END

B

5.REPLACE ECM
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off and leave the vehicle for 30 seconds or more.


d.

Turn the ignition switch to ON for 1 second.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

7.PERFORM LEARNING VALUES SAVE
a.

Remove the new ECM.


b.

Install the old ECM.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Save.


e.

Perform the Learning Values Save.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Learning Values Save
50005 234 240

Result:
Proceed to
NEXT



NEXT

8.PERFORM LEARNING VALUES WRITE
8.PERFORM LEARNING VALUES WRITE
a.

Remove the old ECM.


b.

Install a new ECM.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Write.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Learning Values Write
50005 234 241

Result:
Result Proceed to
Learning Values Save is complete A
Learning Values Save is fail B



A

4.CHECK DTC OUTPUT

B

9.REGISTER INJECTOR COMPENSATION CODE
9.REGISTER INJECTOR COMPENSATION CODE
a.

Register the injector compensation code.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Injector Compensation
50005 234 239

Result:
Proceed to
NEXT



NEXT

10.PERFORM PILOT QUANTITY LEARNING
10.PERFORM PILOT QUANTITY LEARNING
a.

Perform the pilot quantity learning.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Pilot Quantity Learning
50005 234 235

Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT