Refer to DTC P2120.
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>P2120
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2121 | Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance | Either of the following conditions is met (1 trip detection logic):
1.
Difference between VPA and VPA2 is less than 0.4 V, or higher than 1.2 V. (learned value of accelerator off position) 2.
Difference between VPA and VPA2 is greater than or equal to the specified value. |
·
Accelerator pedal sensor assembly ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P2121 | ·
Accel Position ·
Accel Sens. No.1 Volt % ·
Accel Sens. No.2 Volt % |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P2121 | Ignition switch ON for 5 seconds or more.
·
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt %, and Accel Sens. No.2 Volt %. ·
Slowly depress the accelerator pedal until Accel Sens. No.1 Volt % is approximately 30% and Accel Sens. No.2 Volt % is approximately 46%, then slowly release the accelerator pedal. |
Refer to DTC P2120.
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>P2120
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.
| Tester Display |
|---|
| Accel Sens. No.1 Volt % |
| Accel Sens. No.2 Volt % |
| *1 | Accelerator Pedal Assembly |
| *a | Depressed |
| *b | Released |
Read the values.
| Accelerator Pedal | Accel Sens. No.1 Volt % | Accel Sens. No.2 Volt % |
|---|---|---|
| Released | 10 to 22% | 24 to 40% |
| Depressed | 52 to 90% | 68 to 99% |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the accelerator pedal sensor assembly.
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Wait for 5 seconds after turning the ignition switch to ON.
Turn the GTS on.
Operate the accelerator pedal in accordance with the following procedure [B].
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Accel Sens. No.1 Volt %, and Accel Sens. No.2 Volt %.
Slowly depress the accelerator pedal until Accel Sens. No.1 Volt % is approximately 30% and Accel Sens. No.2 Volt % is approximately 46%, then slowly release the accelerator pedal.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P2121 is output | A |
| No DTC is output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Wait for 5 seconds after turning the ignition switch to ON.
Turn the GTS on.
Operate the accelerator pedal in accordance with the following procedure [B].
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Accel Sens. No.1 Volt %, and Accel Sens. No.2 Volt %.
Slowly depress the accelerator pedal until Accel Sens. No.1 Volt % is approximately 30% and Accel Sens. No.2 Volt % is approximately 46%, then slowly release the accelerator pedal.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT