Refer to DTC P0335.
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>P0335
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0337 | Crankshaft Position Sensor "A" Circuit Low Input | Output voltage of crankshaft position sensor is less than 0.3 V for 4 seconds (1 trip detection logic). | ·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
ECM |
Comes on | DTC stored |
| P0338 | Crankshaft Position Sensor "A" Circuit High Input | Output voltage of crankshaft position sensor is higher than 4.7 V for 4 seconds (1 trip detection logic). | ·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
ECM |
Comes on | DTC stored |
If DTC P0337 or P0338 is stored, the following symptoms may appear:
Difficulty starting
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
Reference: Inspection using an oscilloscope.
The correct waveform is as shown.
| ECM Terminal Name | Between G2+ and G2-
Between NE+ and NE- |
| Tester Range | 2 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
When the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V, the ECM stores a DTC.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0337 | Ignition switch ON for 4 seconds or more |
| P0338 |
Refer to DTC P0335.
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>P0335
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Record any output DTC(s).
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Disconnect the crankshaft position sensor connector.
Turn the ignition switch to ON for 4 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Check whether the DTC changes when the connector is disconnected and connected.
| Result | Proceed to |
|---|---|
| DTC does not change | A |
| DTC changes | B |
A
B
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C14-20 (VCNE) - C41-19 (NE-) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z1-1 (NE+) - C41-28 (NE+) | Always | Below 1 Ω |
| Z1-2 (NE-) - C41-19 (NE-) | Always | Below 1 Ω |
| Z1-1 (NE+) or C41-28 (NE+) - Body ground and other terminals | Always | 10 kΩ or higher |
| Z1-2 (NE-) or C41-19 (NE-) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the crankshaft position sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the crankshaft position sensor connector.
| *a | Component with harness connected
(ECM) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C41-20 (VCNE) - C41-28 (NE+) | Ignition switch off | No short or open circuit |
| C41-28 (NE+) - C41-19 (NE-) | Ignition switch off | No short or open circuit |
Reconnect the crankshaft position sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the crankshaft position sensor.
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON for 4 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output.
| Proceed to |
|---|
| NEXT |
NEXT