The circuit is used to send TRC and VSC control information from the skid control ECU (brake actuator assembly) to the ECM, and engine control information from the ECM to the skid control ECU (brake actuator assembly) through the CAN communication system.
for 4WD or w/ Rear Differential Lock:
The rear differential lock identification signal is sent from the 4 wheel drive control ECU to the skid control ECU (brake actuator assembly) via the CAN communication system.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1203 | ECM Communication Circuit Malfunction | Either of the following is detected:
1.
Engine model information sent from the ECM does not match the information stored in the skid control ECU. 2.
The rear differential lock identification signal sent from the 4 wheel drive control ECU does not match the information stored in the skid control ECU.* 3.
No system information stored in the skid control ECU. 4.
Incorrect installation of the skid control ECU, 4 wheel drive control ECU* or ECM. |
·
ECM malfunction or ECM with incorrect part number installed ·
4 wheel drive control ECU malfunction or 4 wheel drive control ECU with incorrect part number installed* ·
Skid control ECU (Brake actuator assembly) |
*: for 4WD or w/ Rear Differential Lock
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
When DTC U0114 is output together with DTC C1203, inspect and repair the trouble areas indicated by DTC U0114 first.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073
Check that the proper ECM is installed.
| Result | Proceed to |
|---|---|
| Proper ECM is installed (for 4WD or w/ Rear Differential Lock) | A |
| Proper ECM is installed (except 4WD or w/o Rear Differential Lock) | B |
| Proper ECM are not installed | C |
A
B
C
for 1GD-FTV: Click herePower Source / Network>1GD-FTV BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for 1GR-FE: Click herePower Source / Network>1GR-FE BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for 1KD-FTV: Click herePower Source / Network>1KD-FTV BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for 2GD-FTV: Click herePower Source / Network>2GD-FTV BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for 2TR-FE: Click herePower Source / Network>2TR-FE BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION
Check that a proper 4 wheel drive control ECU is installed.
| Proceed to |
|---|
| Proper 4 wheel drive control ECU is installed |
| Proper 4 wheel drive control ECU are not installed |
Proper 4 wheel drive control ECU is installed
Proper 4 wheel drive control ECU are not installed
Check if the brake actuator assembly had been replaced before the DTC was recorded.
| Proceed to |
|---|
| The brake actuator assembly is not replaced |
| The brake actuator assembly is replaced |
The brake actuator assembly is not replaced
The brake actuator assembly is replaced
Clear the DTC.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC C1203 is not output |
| DTC C1203 is output |
DTC C1203 is not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTC C1203 is output
Perform initialization and calibration.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTC.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC C1203 is not output |
| DTC C1203 is output |
DTC C1203 is not output
DTC C1203 is output