Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2016.01
RM3270E _54 Brake _041691 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0237426 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1427  Motor Malfunction  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C1427 Motor Malfunction Actuator pump motor does not operate properly.
·

Brake actuator assembly (Ground circuit)

·

Brake actuator assembly (Motor circuit)

·

Wire harness or connector



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform Test Mode (Signal Check) to acquire the rear differential lock identification information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (MOTOR RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


e.

According to the display on the GTS, perform the Active Test.


Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Motor Relay Motor relay Relay ON / OFF Operating sound of motor can be heard.
Vehicle condition: Vehicle stopped
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Motor Relay
50004 105 2
f.

Check the operating sound of the motor relay when operating it with the GTS.


Result:
Proceed to
The operating sound is not heard
The operating sound is heard



The operating sound is not heard

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

The operating sound is heard

3.RECONFIRM DTC
2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A68 skid control ECU (brake actuator assembly) connector.


d.
C260095C48
0.177,0.917 0.51,1.177 0.333,0.26 0.615,1.844 0.615,1.74 0.615,1.74 1.042,1.302 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.219,0.969 0.531,1.167 0.313,0.198 10 false A68 0.438,1.844 0.865,2.052 0.427,0.208 10 false GND2
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A68-13 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)

3.RECONFIRM DTC
HINT:

This code is detected when a problem is identified in the brake actuator assembly.

The motor relay is in the brake actuator assembly.

Therefore, motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.


a.

Turn the ignition switch off.


b.

Reconnect the A68 skid control ECU (brake actuator assembly) connector.



Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
d.

Turn the ignition switch off.


e.

Start the engine.


f.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch to ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (no trouble codes are output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.



Result:
Proceed to
DTC C1427 is not output
DTC C1427 is output



DTC C1427 is not output

DTC C1427 is output