Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2016.01
RM3270E _54 Brake _041691 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0237426 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C146E  Open in ABS Solenoid Relay Circuit  C146F  Short in ABS Solenoid Relay Circuit  


DESCRIPTION

The ABS solenoid relay supplies power to the ABS solenoid.

The solenoid relay is turned on 1.5 seconds after the ignition switch is turned to ON, and is turned off if an open or short in the solenoid is detected by the self diagnosis performed when the engine starts running.

The ABS solenoid relay is housed in the skid control ECU in the actuator assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
C146E Open in ABS Solenoid Relay Circuit When either of the following is detected:
1.

Both of the following conditions continue for 0.22 seconds or more.

·

The IG1 terminal voltage is 9.5 V or more.

·

The solenoid relay contact is open when the relay is ON.


2.

Both of the following conditions continue for 0.22 seconds or more.

·

The IG1 terminal voltage drops below 9.5 V when the relay is turned on.

·

The relay contact remains open.



·

ABS NO. 2 fuse

·

Solenoid relay circuit

·

Brake actuator assembly (Solenoid relay)


C146F Short in ABS Solenoid Relay Circuit Immediately after the ignition switch is turned to ON, the solenoid relay contact is closed for 4.5 seconds when the relay is turned off.
·

Solenoid relay circuit

·

Brake actuator assembly (Solenoid relay)



WIRING DIAGRAM

C284389E04
1.604,1.385 2.396,1.583 0.792,0.198 10 false ABS NO. 2 3.229,1.094 3.542,1.292 0.313,0.198 10 false 12 3.51,1.104 3.969,1.302 0.458,0.198 10 false +BS 4.563,0.75 5.521,0.958 0.958,0.208 10 false Solenoid Relay 5.927,1.583 6.542,1.781 0.615,0.198 10 false SFRH 5.958,2.135 6.573,2.333 0.615,0.198 10 false SFLH 5.979,2.646 6.594,2.844 0.615,0.198 10 false SRRH 6,3.135 6.615,3.333 0.615,0.198 10 false SRLH 5.958,3.635 6.573,3.833 0.615,0.198 10 false SFRR 5.958,4.135 6.573,4.333 0.615,0.198 10 false SFLR 5.958,4.635 6.573,4.833 0.615,0.198 10 false SRRR 5.969,5.135 6.583,5.333 0.615,0.198 10 false SRLR 3.323,4.969 3.479,5.167 0.156,0.198 10 false 1 3.563,5.083 4.177,5.281 0.615,0.198 10 false GND1 3.76,7.917 4.219,8.115 0.458,0.198 10 false A68 4.479,4.198 5.594,4.385 1.115,0.188 10 false Skid Control ECU 3.781,8.083 5.448,8.281 1.667,0.198 10 false Brake Actuator Assembly 0.177,1.198 1.01,1.396 0.833,0.198 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform Test Mode (Signal Check) to acquire the rear differential lock identification information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When C1241 is output together with C146E and/or C146F, inspect and repair the trouble areas indicated by C1241 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1241


PROCEDURE

1.CHECK TERMINAL VOLTAGE (+BS TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A68 skid control ECU (brake actuator assembly) connector.


d.
C260095C50
0.208,0.948 0.531,1.271 0.323,0.323 2.49,0.823 2.677,0.271 true 0.063,0.042 0.375,0.198 0.313,0.156 10 false *a 0.25,1.021 0.563,1.219 0.313,0.198 10 false A68 2.708,0.146 3.167,0.344 0.458,0.198 10 false +BS
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A68-12 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C260095C46
0.219,0.927 0.563,1.156 0.344,0.229 1.115,0.833 1.26,0.146 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.26,0.958 0.573,1.156 0.313,0.198 10 false A68 1.292,0.063 1.906,0.26 0.615,0.198 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A68-1 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

3.RECONFIRM DTC
HINT:

These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).

The solenoid circuits are in the skid control ECU (brake actuator assembly).

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed.

Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).


a.

Reconnect the A68 skid control ECU (brake actuator assembly) connector.



Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC C146E and/or C146F are not output
DTC C146E and C146F are output


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch to ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness from the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.




DTC C146E and/or C146F are not output

DTC C146E and C146F are output