Refer to DTCs C1271, C1272, C1401 and C1402.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1271
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| C1405 | Open or Short in Front Speed Sensor RH Circuit | Either of the following is detected:
1.
An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2.
With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more. |
·
Front speed sensor RH ·
Skid control ECU (Brake actuator assembly) ·
Wire harness or connector |
- |
| C1406 | Open or Short in Front Speed Sensor LH Circuit | Either of the following is detected:
1.
An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2.
With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more. |
·
Front speed sensor LH ·
Skid control ECU (Brake actuator assembly) ·
Wire harness or connector |
- |
When replacing the skid control ECU (brake actuator assembly), perform Test Mode (Signal Check) to acquire the rear differential lock identification information.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE
Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Speed Open | Front speed sensor RH open detection | Normal or Error | Normal | Error: Momentary interruption |
| FL Speed Open | Front speed sensor LH open detection | Normal or Error | Normal | Error: Momentary interruption |
| Tester Display |
|---|
| FR Speed Open |
| FL Speed Open |
Normal (There are no momentary interruptions.)
Perform the above inspection before removing the sensor and connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| FR Wheel Speed |
| FL Wheel Speed |
Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.
Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK
The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the engine switch off.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
Turn the engine switch off.
Start the engine.
Perform a road test
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTCs C1405 and C1406 are not output |
| DTCs C1405 and/or C1406 are output |
DTCs C1405 and C1406 are not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTCs C1405 and/or C1406 are output
Turn the engine switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the A68 skid control ECU (brake actuator assembly) connector and the A6 and/or A7 front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A68-7 (FR+) - A6-2 (FR+) | Always | Below 1 Ω |
| A68-6 (FR-) - A6-1 (FR-) | Always | Below 1 Ω |
| A68-7 (FR+) or A6-2 (FR+) - Body ground | Always | 10 kΩ or higher |
| A68-6 (FR-) or A6-1 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A68-19 (FL+) - A7-2 (FL+) | Always | Below 1 Ω |
| A68-18 (FL-) - A7-1 (FL-) | Always | Below 1 Ω |
| A68-19 (FL+) or A7-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| A68-18 (FL-) or A7-1 (FL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for RH |
| *B | for LH |
| *a | Front view of wire harness connector
(to Front Speed Sensor) |
Reconnect the A68 skid control ECU (brake actuator assembly) connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A6-2 (FR+) - Body ground | Engine switch on (IG) | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A7-2 (FL+) - Body ground | Engine switch on (IG) | 8 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR(for 4WD and Pre-Runner)>REMOVAL
NG