Home › Drivetrain › AC60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE) › from 2016.01
RM3270E _52 Drivetrain _041680 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0239143 AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE) C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE)  P2716  Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)  


DESCRIPTION

Refer to the system description for DTC P2714.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE)>P2714

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip detection logic).
·

Open or short in shift solenoid valve SLT circuit

·

Shift solenoid valve SLT

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the ECM interprets this as a fault. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C352693E08
5.75,0.781 6.208,0.979 0.458,0.198 10 false 12 V 5.167,1.146 5.625,1.344 0.458,0.198 10 false SLT+ 4.958,1.146 5.417,1.344 0.458,0.198 10 false 5 5.167,2.115 5.625,2.313 0.458,0.198 10 false SLT- 5.521,3.042 5.979,3.24 0.458,0.198 10 false C148 5.521,3.219 5.979,3.417 0.458,0.198 10 false ECM 4.969,2.115 5.427,2.313 0.458,0.198 10 false 4 3.885,2.115 4.344,2.313 0.458,0.198 10 false 14 3.885,1.146 4.344,1.344 0.458,0.198 10 false 13 3.479,1.146 3.938,1.344 0.458,0.198 10 false SLT+ 3.49,2.115 3.948,2.313 0.458,0.198 10 false SLT- 1.438,1.729 3.104,1.969 1.667,0.24 10 false Shift Solenoid Valve SLT 1.25,1.333 1.708,1.531 0.458,0.198 10 false 1 1.271,2.115 1.729,2.313 0.458,0.198 10 false 2 1.719,2.667 2.167,2.823 0.448,0.156 10 false C31 1.719,2.844 3.354,3.115 1.635,0.271 10 false Transmission Wire

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE)>INITIALIZATION


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)
a.
C319326C13
1.823,1.76 1.969,1.177 true 2.448,1.74 2.188,1.177 true 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 1.656,1.823 2.125,2.021 0.469,0.198 10 false SLT- 2.354,1.813 2.771,2 0.417,0.188 10 false SLT+
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (SLT+) - 14 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
13 (SLT+) - Body ground Always 10 kΩ or higher
14 (SLT-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLT
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C325711C26
1.552,0.198 1.906,0.427 0.354,0.229 2.333,2.74 1.74,1.635 true 1.271,2.74 1.656,1.635 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 1.563,0.229 1.906,0.427 0.344,0.198 10 false C148 2.125,2.792 2.813,2.979 0.688,0.188 10 false 4 (SLT-) 0.979,2.781 1.729,2.979 0.75,0.198 10 false 5 (SLT+)
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C148-5 (SLT+) - C148-4 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
C148-5 (SLT+) - Body ground Always 10 kΩ or higher
C148-4 (SLT-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SLT
a.
C201747C15
1.49,0.875 0.635,0.646 false 1.781,0.865 2.479,0.625 false 1.49,3.125 0.635,2.896 false 1.781,3.125 2.479,2.885 false 2.542,0.552 2.719,0.75 0.177,0.198 10 false 1 0.51,0.563 0.688,0.76 0.177,0.198 10 false 2 1.177,4.198 1.385,4.406 0.208,0.208 10 false (-) 1.917,4.208 2.146,4.406 0.229,0.198 10 false (+) 2.563,2.792 2.74,2.99 0.177,0.198 10 false 1 0.49,2.813 0.667,3.01 0.177,0.198 10 false 2 0.135,0.135 0.354,0.344 0.219,0.208 10 false *1
*1 Shift Solenoid Valve SLT


Remove shift solenoid valve SLT.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG