Home › Drivetrain › AC60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE) › from 2016.01
RM3270E _52 Drivetrain _041680 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0239143 AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE) C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE)  P2757  Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU)  


SYSTEM DESCRIPTION

The ECM uses the signals from the throttle position sensor, air-flow meter, input turbine speed sensor, output shaft speed sensor and crankshaft position sensor to monitor the engagement condition of the lock-up clutch.

C318299E01
1.656,0.292 1.854,0.292 1.854,0.292 2.229,0.771 true 1.656,1.25 1.854,1.25 1.854,1.25 2.292,0.938 true 3.771,0.292 3.583,0.292 3.583,0.292 3.271,0.771 true 0.885,0.208 2.573,0.406 1.688,0.198 10 false Spool Valve 1.208,1.156 2.125,1.354 0.917,0.198 10 false Sleeve 3.833,0.219 5.063,0.417 1.229,0.198 10 false Solenoid 4.51,0.615 5.104,1.052 0.594,0.438 10 false Hydraulic Pressure 5.823,1.438 6.896,1.635 1.073,0.198 10 false Current

The ECM compares the engagement condition of the lock-up clutch with the lock-up schedule in the ECM memory to detect shift solenoid valve SLU, transmission valve body assembly and torque converter assembly mechanical problems.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2757 Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU)
Both conditions are met (2 trip detection logic):
·

Lock-up does not occur when requested.

·

Lock-up occurs when shift solenoid valve SLU is requested to turn on in the lock-up range.


·

Shift solenoid valve SLU remains open or closed

·

Transmission valve body assembly is blocked

·

Torque converter assembly

·

Automatic transmission assembly (clutch, brake or gear, etc.)

·

Line pressure is too low


Comes on DTC stored

MONITOR DESCRIPTION

Torque converter lock-up is controlled by the ECM based on the transmission revolution sensor (NT), transmission revolution sensor (SP2), engine speed, engine load, engine temperature, vehicle speed, transmission fluid temperature and gear selection. The ECM determines the lock-up status of the torque converter by comparing the engine speed (NE) to the input turbine speed (NT). The ECM calculates the actual transmission gear by comparing the input turbine speed (NT) to the output shaft speed (SP2).

When conditions are appropriate, the ECM requests "lock-up" by applying control voltage to shift solenoid valve SLU. When shift solenoid valve SLU is turned on, it applies pressure to the lock-up relay valve and locks the torque converter.

If the ECM detects no lock-up after lock-up has been requested or if it detects lock-up when it is not requested, the ECM interprets this as a fault in shift solenoid valve SLU or lock-up system performance.

The ECM will illuminate the MIL and store the DTC.

HINT:

Example:

When any of the following is met, the system judges it as a malfunction.

·

There is a difference in rotation speed between the input side (engine speed) and output side (input turbine speed) of the torque converter when the ECM commands lock-up. (Engine speed is at least 70 rpm more than the input turbine speed.)

·

There is no difference in rotation speed between the input side (engine speed) and output side (input turbine speed) of the torque converter when the ECM commands lock-up off. (The difference between engine speed and input turbine speed is less than 35 rpm.)



CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE)>INITIALIZATION


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

2.

Turn the ignition switch off.

3.

Perform step (*1) again.



ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the GTS, perform the Active Test.

Powertrain > Engine > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the Lock Up Controls the shift solenoid valves SLU and SL to set the automatic transmission to the lock-up condition ON/OFF Can be used to check shift solenoid valves SLU and SL operation.
[Vehicle Condition]
·

Throttle valve opening angle: Less than 30%

·

Vehicle speed: 80 km/h (50 mph) or more


Powertrain > Engine > Active Test
Tester Display
Activate the Lock Up
50004 234 115
HINT:

This test can be conducted when the vehicle speed is 80 km/h (50 mph) or more.




h.

Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.

HINT:
·

When changing the accelerator pedal opening angle while driving, if the engine speed does not change, lock-up is on.

·

Slowly release the accelerator pedal in order to decelerate, but do not fully release the pedal. (Fully releasing the pedal will close the throttle valve and lock-up may be turned off.)



C159073E07
4.542,2.219 5.521,1.99 5.521,1.99 5.583,1.99 false 5.167,2.24 5.51,2.625 5.51,2.625 5.573,2.625 false 0.792,2.677 1.844,2.927 1.052,0.25 10 Engine Speed 0.708,1.708 1.865,2.104 1.156,0.396 10 Accelerator Pedal Fully Released 0.708,1.042 1.844,1.448 1.135,0.406 10 Accelerator Pedal Opening Angle 5.01,3.156 5.5,3.385 0.49,0.229 10 Time 5.708,1.917 6.708,2.177 1.0,0.26 10 Lock-up OFF 5.677,2.542 6.708,2.823 1.031,0.281 10 Lock-up ON



PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2757)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

e.

Read the DTCs using the GTS.

Result:
Result Proceed to
Only DTC P2757 is output A
P2757 and other DTCs are output B


HINT:

If any DTCs other than P2757 are output, perform troubleshooting for those DTCs first.




A

2.INSPECT SHIFT SOLENOID VALVE SLU

B

2.INSPECT SHIFT SOLENOID VALVE SLU
a.
C201747C15
1.49,0.875 0.635,0.646 false 1.781,0.865 2.479,0.625 false 1.49,3.125 0.635,2.896 false 1.781,3.125 2.479,2.885 false 2.542,0.552 2.719,0.75 0.177,0.198 10 false 1 0.51,0.563 0.688,0.76 0.177,0.198 10 false 2 1.177,4.198 1.385,4.406 0.208,0.208 10 false (-) 1.917,4.208 2.146,4.406 0.229,0.198 10 false (+) 2.563,2.792 2.74,2.99 0.177,0.198 10 false 1 0.49,2.813 0.667,3.01 0.177,0.198 10 false 2 0.135,0.135 0.354,0.344 0.219,0.208 10 false *1
*1 Shift Solenoid Valve SLU


Remove shift solenoid valve SLU.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY

OK:

There is no foreign matter on each valve and they operate smoothly.



Result:
Proceed to
OK
NG



OK

4.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

4.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Check the torque converter assembly.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION

OK:

The torque converter assembly operates normally.



Result:
Proceed to
OK
NG



OK

NG