Home › Drivetrain › AC60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE) › from 2016.01
RM3270E _52 Drivetrain _041680 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0239143 AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE) C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE)  P2810  Pressure Control Solenoid "G" Electrical (Shift Solenoid Valve SL4)  


DESCRIPTION

Changing from 1st to 6th is performed by the ECM turning shift solenoid valves SL1, SL2, SL3 and SL4 on and off. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE)>FAIL-SAFE CHART

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2810 Pressure Control Solenoid "G" Electrical (Shift Solenoid Valve SL4) An open or short circuit (output signal duty is 0% or 100%) is detected by the ECM in the shift solenoid valve SL4 circuit while driving and shifting gears (SL4 output signal duty is more than 0% and less than 100% under normal conditions) (1 trip detection logic).
·

Open or short in shift solenoid valve SL4 circuit

·

Shift solenoid valve SL4

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL4 circuit. The ECM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any of the shift solenoid valve circuits, the ECM detects the problem and illuminates the MIL and stores the DTC. The ECM also performs the fail-safe function and turns the other normal shift solenoid valves on or off. (In case of an open or short circuit, the ECM stops sending current to the circuit.)

While driving and shifting gears, if the ECM detects an open or short in the shift solenoid valve SL4 circuit, the ECM determines there is a malfunction.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE)>FAIL-SAFE CHART

WIRING DIAGRAM

C352693E10
5.75,0.781 6.208,0.979 0.458,0.198 10 false 12 V 5.167,1.146 5.625,1.344 0.458,0.198 10 false SL4+ 4.906,1.146 5.365,1.344 0.458,0.198 10 false 13 5.167,2.115 5.625,2.313 0.458,0.198 10 false SL4- 5.521,3.042 5.979,3.24 0.458,0.198 10 false C148 5.521,3.219 5.979,3.417 0.458,0.198 10 false ECM 4.917,2.115 5.375,2.313 0.458,0.198 10 false 12 3.885,2.115 4.344,2.313 0.458,0.198 10 false 24 3.885,1.146 4.344,1.344 0.458,0.198 10 false 23 3.479,1.146 3.938,1.344 0.458,0.198 10 false SL4+ 3.5,2.115 3.958,2.313 0.458,0.198 10 false SL4- 1.438,1.729 3.104,1.969 1.667,0.24 10 false Shift Solenoid Valve SL4 1.25,1.333 1.708,1.531 0.458,0.198 10 false 1 1.271,2.115 1.729,2.313 0.458,0.198 10 false 2 1.719,2.667 2.167,2.823 0.448,0.156 10 false C31 1.719,2.844 3.354,3.115 1.635,0.271 10 false Transmission Wire

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE)>INITIALIZATION


HINT:
·

The following table shows normal operation of the shift solenoid valve SL4 when the shift lever is in D:

ECM commanded gear 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve SL4 OFF OFF ON OFF ON OFF

·

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.




PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL4)
a.
C319326C10
1.75,1.74 1.969,1.365 true 2.385,1.708 2.188,1.375 true 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 1.521,1.771 1.99,1.969 0.469,0.198 10 false SL4- 2.24,1.771 2.708,2.031 0.469,0.26 10 false SL4+
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
23 (SL4+) - 24 (SL4-) 20°C (68°F) 5.0 to 5.6 Ω
23 (SL4+) - Body ground Always 10 kΩ or higher
24 (SL4-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SL4
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C325711C29
1.531,0.188 1.927,0.427 0.396,0.24 2.333,2.74 1.771,1.719 true 1.271,2.74 1.708,1.719 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 1.552,0.229 1.896,0.427 0.344,0.198 10 false C148 2.135,2.792 2.823,2.979 0.688,0.188 10 false 12 (SL4-) 0.927,2.781 1.677,2.979 0.75,0.198 10 false 13 (SL4+)
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C148-13 (SL4+) - C148-12 (SL4-) 20°C (68°F) 5.0 to 5.6 Ω
C148-13 (SL4+) - Body ground Always 10 kΩ or higher
C148-12 (SL4-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SL4
a.
C201747C15
1.49,0.875 0.635,0.646 false 1.781,0.865 2.479,0.625 false 1.49,3.125 0.635,2.896 false 1.781,3.125 2.479,2.885 false 2.542,0.552 2.719,0.75 0.177,0.198 10 false 1 0.51,0.563 0.688,0.76 0.177,0.198 10 false 2 1.177,4.198 1.385,4.406 0.208,0.208 10 false (-) 1.917,4.208 2.146,4.406 0.229,0.198 10 false (+) 2.563,2.792 2.74,2.99 0.177,0.198 10 false 1 0.49,2.813 0.667,3.01 0.177,0.198 10 false 2 0.135,0.135 0.354,0.344 0.219,0.208 10 false *1
*1 Shift Solenoid Valve SL4


Remove shift solenoid valve SL4.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG