Home › Power Source / Network › 1GR-FE BATTERY / CHARGING › GENERATOR(for 100A Type) › from 2016.01
RM3270E _57 Power Source / Network _048962 1GR-FE BATTERY / CHARGING _0239224 GENERATOR(for 100A Type) A

1GR-FE BATTERY / CHARGING  GENERATOR(for 100A Type)  DISASSEMBLY  


PROCEDURE

Hide 27411 1.REMOVE GENERATOR PULLEY

a.

Mount the generator assembly in the vise between aluminum plates.


b.
A360335C01
2.25,0.146 2.417,0.146 2.417,0.146 3.031,0.375 true 2.906,1.177 2.906,0.885 2.906,0.885 3.208,0.583 true 2.313,1.979 2.563,2.167 0.25,0.188 10 true *a 1.688,0.063 2.76,0.26 1.073,0.198 10 false SST 1-B 2.635,1.198 3.365,1.417 0.729,0.219 10 false SST 1-A
*a Hold
V100135

Turn


Install SST 1-A to the pulley shaft.

SST
09820-63011  (09820-06010, 09820-06021)

SST 1-A and B 09820-06010
SST 2 09820-06021


c.

Install SST 1-B to SST 1-A.


d.

Hold SST 1-A with a torque wrench and turn SST 1-B clockwise with the specified torque.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:

Make sure that SST is secured to the generator rotor shaft.



e.
A346990C01
2.583,0.75 2.75,0.417 2.75,0.417 2.833,0.417 false 2,0.781 2.25,0.198 2.25,0.198 2.333,0.198 false 2.906,0.333 3.406,0.583 0.5,0.25 10 false SST 2 2.385,0.115 3.167,0.333 0.781,0.219 10 false SST 1-A
V100135

Insert


Install SST 2 and attach it to the pulley nut.


f.
A360336C01
2.052,0.771 2.167,0.417 2.167,0.417 2.25,0.417 false 1.833,0.76 2,0.167 2,0.167 2.083,0.167 false 1.531,1.635 1.844,1.792 0.313,0.156 10 true *a 2.302,0.323 3.052,0.521 0.75,0.198 10 false SST 1-A 2.167,0.073 2.917,0.271 0.75,0.198 10 false SST 2
*a Hold
V100135

Turn


To loosen the pulley nut, turn SST 1-A as shown in the illustration.

NOTICE:

To prevent damage to the generator rotor shaft, do not loosen the pulley nut more than one-half of a turn.



g.

Remove SST 2 from the generator assembly.


h.
A360337C01
2.323,0.188 2.49,0.188 2.49,0.188 3.052,0.375 true 2.948,1.188 2.948,0.875 2.948,0.875 3.198,0.594 true 2.563,1.615 2.875,1.771 0.313,0.156 10 false *a 1.76,0.094 2.833,0.292 1.073,0.198 10 false SST 1-B 2.656,1.219 3.406,1.448 0.75,0.229 10 false SST 1-A
*a Hold
V100135

Turn


Turn SST 1-B as shown in the illustration and remove SST 1-A and B.


i.

Remove the pulley nut and generator pulley.


j.

Remove the generator assembly from the vise.


Hide 27039 2.REMOVE GENERATOR REAR END COVER

a.
A346993

Place the generator assembly on the generator pulley.


b.

Remove the 3 bolts and generator rear end cover from the generator coil assembly.


Hide 27387 3.REMOVE TERMINAL INSULATOR

a.
A346994

Remove the terminal insulator from the generator coil assembly.


Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A346995

Remove the 2 screws and generator brush holder assembly from the generator coil assembly.


Hide 27360 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A346996

Remove the 4 through bolts.


b.
A346997C01
2.01,0.906 2.5,0.646 2.5,0.646 2.594,0.646 true 0.573,1.573 1.375,2 1.375,2 1.469,2 true 0.573,0.542 0.885,0.698 0.313,0.156 10 false *a 2.656,0.552 3.115,0.75 0.458,0.198 10 false SST 1.542,1.906 2,2.104 0.458,0.198 10 false SST
*a Hold
V100135

Turn


Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


Hide 27444 6.REMOVE GENERATOR BEARING COVER PACKING

a.
A284548

Remove the generator bearing cover packing.

NOTICE:

If the generator bearing cover packing breaks, remove all broken pieces.


HINT:

The generator bearing cover packing may be installed on the generator rotor assembly.



Hide 27330 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.

Remove the generator rotor assembly from the generator drive end frame.


Hide 27310B 8.INSPECT GENERATOR DRIVE END FRAME BEARING

A346999

a.

Check that the generator drive end frame bearing is not rough or worn and that it rotates smoothly.

If necessary, replace the generator drive end frame bearing.


Hide 27310B 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A347000

Remove the 4 screws and retainer plate from the generator drive end frame.


b.
A347001N01
2.51,0.938 1.896,0.292 1.896,0.292 2.646,0.573 true 1.563,0.198 2.021,0.396 0.458,0.198 10 false SST

Using SST and a hammer, tap out the generator drive end frame bearing from the generator drive end frame.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)