Home › Power Source / Network › 1KD-FTV BATTERY / CHARGING › GENERATOR › from 2016.01
RM3270E _57 Power Source / Network _048963 1KD-FTV BATTERY / CHARGING _0239227 GENERATOR A

1KD-FTV BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27415 1.REMOVE GENERATOR WITH CLUTCH PULLEY

a.

Mount the generator assembly in the vise between aluminum plates.


b.
A343823C01
1.74,1.031 1.948,0.24 1.948,0.24 3.052,0.688 true 1.844,0.24 1.948,0.24 false 1.24,1.208 1.792,1.792 1.792,1.792 1.917,1.792 true 2.177,1.375 2.177,0.865 true 2.104,1.354 2.417,1.51 0.313,0.156 10 false *a 1.365,0.135 2.135,0.333 0.771,0.198 10 false SST A 1.969,1.688 2.74,1.885 0.771,0.198 10 false SST B
*a Generator Rotor Shaft


Install SST A and B to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  (09821-63011, 09821-63020)

NOTICE:

Securely attach SST to the generator pulley with clutch and generator rotor shaft.



c.
A343824C01
1.958,0.615 2.458,0.156 2.458,0.156 2.552,0.156 true 2.219,0.813 2.531,0.813 true 1.99,1.969 2.302,2.125 0.313,0.156 10 false *a 2.604,0.719 3.375,0.917 0.771,0.198 10 false SST A 2.615,0.063 3.385,0.26 0.771,0.198 10 false SST B
*a Hold
V100135

Turn


Using a wrench to hold SST A, turn SST B counterclockwise to loosen the generator pulley with clutch.

NOTICE:

Be careful as the generator pulley with clutch or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.



d.

Remove SST from the generator assembly.


e.

Remove the generator pulley with clutch from the generator rotor shaft.


f.

Remove the generator assembly from the vise.


Hide 27039 2.REMOVE GENERATOR REAR END COVER

a.

Place the generator assembly on the generator pulley with clutch.


b.
A343825

Remove the 3 bolts and generator rear end cover from the generator coil assembly.


Hide 27387 3.REMOVE TERMINAL INSULATOR

a.
A343826

Remove the terminal insulator from the generator coil assembly.


Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A343827

Remove the 2 screws and generator brush holder assembly from the generator coil assembly.


Hide 27360 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A343828

Remove the 4 through bolts.


b.
A343800C01
2.052,1.177 2.646,0.781 2.646,0.781 2.74,0.781 true 0.542,1.688 1.021,2.063 1.021,2.063 1.156,2.063 true 0.438,0.625 0.75,0.781 0.313,0.156 10 false *a 2.792,0.698 3.25,0.896 0.458,0.198 10 false SST 1.198,1.958 1.656,2.156 0.458,0.198 10 false SST
*a Hold
V100135

Turn


Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


Hide 27444 6.REMOVE GENERATOR BEARING COVER PACKING

a.
A341809

Remove the generator bearing cover packing.

NOTICE:

If the generator bearing cover packing breaks, remove all broken pieces.


HINT:

The generator bearing cover packing may be installed on the generator rotor assembly.



Hide 27330 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.

Remove the generator rotor assembly from the generator drive end frame.


Hide 27310B 8.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A343831

Check that the generator drive end frame bearing is not rough or worn and that it rotates smoothly.

If necessary, replace the generator drive end frame bearing.


Hide 27310B 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A343832

Remove the 4 screws and retainer plate from the generator drive end frame.


b.
A343833N01
2.49,0.854 2.042,0.281 2.042,0.281 2.656,0.542 true 1.708,0.167 2.167,0.365 0.458,0.198 10 false SST

Using SST and a hammer, tap out the generator drive end frame bearing from generator drive end frame.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)