Home › Power Source / Network › 2KD-FTV BATTERY / CHARGING › GENERATOR › from 2016.01
RM3270E _57 Power Source / Network _048965 2KD-FTV BATTERY / CHARGING _0239235 GENERATOR A

2KD-FTV BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A343834N01
2.302,0.844 1.844,0.219 1.844,0.219 2.438,0.51 true 1.542,0.125 2,0.323 0.458,0.198 10 false SST

Using SST and a press, press in a new generator drive end frame bearing.

SST
09950-60010  (09951-00520)
09950-70010  (09951-07100)


b.
A343835C01
1.896,0.156 1.969,0.156 1.969,0.156 2.75,0.792 true 1.969,2 2.042,2 2.042,2 2.75,1.208 true 1.688,0.063 2,0.219 0.313,0.156 10 false *a 1.771,1.896 2.083,2.052 0.313,0.156 10 false *b
*a Tab
*b Cutout


Fit the tabs on the retainer plate into the cutouts on the generator drive end frame.


c.

Install the retainer plate with the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Place the generator drive end frame on the generator pulley with clutch.


b.

Install the generator rotor assembly to the generator drive end frame.


Hide 27444 3.INSTALL GENERATOR BEARING COVER PACKING

NOTICE:

A new generator coil assembly comes with a generator bearing cover packing. Therefore, it is not necessary to install a new generator bearing cover packing when installing a new generator coil assembly.


a.
A314531C08
1.938,0.5 2.448,0.5 true 1.927,1.448 2.438,1.448 true 2.49,0.417 2.802,0.573 0.313,0.156 10 false *a 2.479,1.385 2.792,1.542 0.313,0.156 10 false *b
*a Protrusion
*b Groove


Install a new generator bearing cover packing to the generator coil assembly.

NOTICE:

Align the protrusion of the generator bearing cover packing with the groove of the generator coil assembly when installing.



Hide 27360 4.INSTALL GENERATOR COIL ASSEMBLY

a.
A343806C01
0.583,0.292 0.667,0.292 0.667,0.292 1.219,0.708 true 1.896,0.271 2,0.271 2,0.271 2.542,0.698 true 1.75,0.167 2.063,0.323 0.313,0.156 10 false *a 0.427,0.188 0.74,0.344 0.313,0.156 10 false *a
*a 21 mm Deep Socket Wrench


Using a 21 mm deep socket wrench and press, slowly press on the generator coil assembly.


b.

Install the generator coil assembly with the 4 through bolts.

Torque:
5.6 N*m (57 kgf*cm, 50 in.*lbf)


Hide 27370 5.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A113845C09
0.99,0.531 1.219,0.344 1.219,0.344 1.313,0.344 false 1.375,0.25 1.604,0.396 0.229,0.146 10 false *a
*a Pin


While pushing the 2 brushes into the generator brush holder assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.


b.
A343827C01
0.844,1.875 0.948,1.875 0.948,1.875 1.521,0.948 true 0.635,1.771 0.948,1.927 0.313,0.156 10 false *a
*a Pin


Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the generator brush holder assembly.


Hide 27387 6.INSTALL TERMINAL INSULATOR

a.
A343837

Install the terminal insulator to the generator coil assembly.

NOTICE:

Make sure that the terminal insulator is installed with the correct orientation.



Hide 27039 7.INSTALL GENERATOR REAR END COVER

a.

Install the generator rear end cover to the generator coil assembly with the 3 bolts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 27415 8.INSTALL GENERATOR WITH CLUTCH PULLEY

a.

Mount the generator assembly in the vise between aluminum plates.


b.

Temporarily install the generator pulley with clutch by hand.


c.
A343838C01
0.51,0.677 1.542,0.167 1.542,0.167 1.792,0.906 true 1.542,0.167 1.656,0.167 false 1.521,1.75 1.635,1.75 1.635,1.75 2.344,1.115 true 1.323,0.885 1.323,1.396 true 1.75,0.083 2.208,0.281 0.458,0.198 10 false SST A 1.052,1.635 1.51,1.833 0.458,0.198 10 false SST B 1.26,1.365 1.573,1.521 0.313,0.156 10 false *a
*a Generator Rotor Shaft


Install SST A and B to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  

NOTICE:

Securely attach SST to the generator pulley with clutch and generator rotor shaft.



d.
A343839C01
0.771,0.323 0.885,0.323 0.885,0.323 1.156,0.906 true 0.542,1.583 0.656,1.583 0.656,1.583 0.885,1.156 true 0.833,2.719 1.146,2.875 0.313,0.156 10 false *a 1.99,2.344 2.302,2.5 0.313,0.156 10 false *b 1.385,4.115 1.698,4.271 0.313,0.156 10 false *c 0.083,1.479 0.854,1.677 0.771,0.198 10 false SST A 0.302,0.229 1.073,0.427 0.771,0.198 10 false SST B
*a Hold
*b Torque Wrench Fulcrum Length
*c SST Fulcrum Length
V100135

Turn


Using a wrench to hold SST A, turn SST B clockwise to tighten the generator pulley with clutch.

Torque:
Specified tightening torque : 110.5 N*m (1127 kgf*cm, 81 ft.*lbf)

NOTICE:

Be careful as the generator pulley with clutch or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 100 mm (3.94 in.)) + torque wrench (fulcrum length of 400 mm (15.8 in.)):

88.4 N*m (901 kgf*cm, 65 ft.*lbf)




e.

Remove SST from the generator assembly.


f.

Check that the generator pulley with clutch rotates smoothly.


g.

Remove the generator assembly from the vise.